100-2000 CCA Automotive Battery Load Tester Cranking Charging System Alternator Tester Battery Analyzer for Car Truck Motorcycle SUV ATV Boat
Features:
1.Wide battery coverage: Test 12V 24V batteries rated from 100 CCA to 2000 CCA.
2.Battery types:Regular flooded, AGM flat plate, AGM spiral, GEL and EFB.
3.Test Standards: CCA,BCI,CA,MCA,Slr,DIN,EN,SAE,IEC,GB.
4.Battery health check, cranking & charging system test
5.Support 5 languages: English, French, Spanish, German, Italian
6.Quick and accurate test result: Quick starter analysis without disabling the ignition, display in just 3 seconds, Accuracy up to 99.95%;
7.Compatible with Multiple Vehicle Types:Cars Trucks SUV ATV Boats Motorcycles Vehicle,etc.
8.Safe design of reverse connection protection:This auto battery tester will not work If you accidentally reverse the two wires.
9.Plug and play:enter the battery voltage and CCA on the battery analyzer to quickly test.
10.Support both in-vehicle and out-of-vehicle test, no need to remove the battery.
What Can Be Done with AUTOPHIX BAS100 Auto Battery Tester?
Battery Test:The car battery analyzer shows 5 different results: “GOOD BATTERY”, “GOOD-RECHARGE”,“REPLACE BATTERY”,“BAD CELL-REPLACE”, “CHARGE&RETEST”
Charging test:check the charging system status to avoid damaging the battery because of overcharge or incomplete
Cranking test: help you test and analyze the starting motor to check it works properly or not.
Why You Need A AUTOPHIX BAS100 Car Battery Tester?
You must have met one of following situations about car battery:
1. Spending a lot of money and time on car battery testing and try to keep the battery working normally;
2. Found a battery for replacement but concerned about the actual battery health condition;
3.Long-time unused batteries being vulnerable to damages.
AUTOPHIX BAS100 battery load tester is your best choice! All the battery-related tests can be conducted with a simple click. Providing overall analysis of battery’s health, help you know battery's status,save your time and money. Five Different Results of Battery Testing:
GOOD BATTERY : Return the battery to service
GOOD-RECHARGE : Fully charge the battery and return it to service
CHARGE&RETEST : Fully charge the battery and retest.Failure to fully charge the battery before retesting may cause inaccurate result.If CHARGE&RETEST appears again after you fully charge the battery,replace the battery.
REPLACEBATTERY : Replace the battery and retest.A REPLACE BATTERY result may also mean a poor connection between the battery cables and the battery.After disconnecting the battery cables,retest the battery using the out-of-vehicle test before replacing it.
BAD CELL-REPLACE : Replace the battery and retest.
Perfect Compatible with all 100-2000 CCA 12V 24V Car,Boat,Motorcycle Batteries
FAQ：
Q:Does this battery tester have power?
A: No, it can only be powered by the tested battery,
Q:Can BAS100 charge the battery?
A: No, it will not charge any batteries. But it can detect the battery.
Q:Can BAS100 get the battery life?
A: Yes. It will give you the health of the battery and a charge percentage.
Q: Why is the result of the BAS100 test inaccurate?
A: Maybe the parameter you set is wrong. Please input the correct data from the battery label.
|
|
|
|---|---|---|
Battery Health TestAfter you connect this automotive battery analyzer to battery, you’ll get the readings of internal resistance, state of charge,state of health and test result accurately and quickly.State of health (SoH) is a figure of merit of the condition of a battery (or a cell, or a battery pack), compared to its ideal conditions. State of charge (SoC) is the level of charge of an electric battery relative to its capacity, SoC is normally used when discussing the current state of a battery in use. | Charging TestIn the ignition state,test whether the generator module works normally through Ripple Test,Loaded test,Unload test. Before test:The engine must be ON during test in order to have results. Ensure all electrical accessories and devices remain in the OFF state. Turning ON/OFF any electrical accessories in the vehicle during the test will affect the accuracy of the test result. | Cranking TestCranking test of our AUTOPHIX BAS100 battery analyzer can help you analyze the starting motor including cranking voltage and the cranking time to check whether the starting motor works properly. before test:the engine and all other accessory loads must be OFF during test in order to have accurate results. |
|
|
|
|---|---|---|
Review DataThis automotive battery load tester has a humanized “Review Data” function,It can automatically record the most recent test result.you can get the previous data to avoid the retest from the scratch,Bring you a good battery test experience. | Safety FeaturesThis battery tester keep operation safe for every users,it has three protection functions: Against Reverse-Polarities---prevents damage if the battery clamps are connected to the wrong terminals; Against Overheating---automatically shut the tester off when reaching the temperature limit. Against Sparks----saving you from the possibility of a fire. | Fast & AccurateWith the powerful APM32 main chip,the speed of AUTOPHIX BAS100 12V automotive battery analyzer is much faster than others,you can get the testing result in 3 seconds and the accuracy is above 99.5%. |
 |  |  |
Support Multiple Languages Our car battery load tester support multiple languages:English,French, Spanish,German,Italian. Provide convenience for your test battery process. | Convenient Testing SituationSupport both in-vehicle and out-of-vehicle tests,no need to remove the battery from the vehicle.the best car battery tester will finish its testing job excellently. | Working TemperatureNo afraid of extreme weather, AUTOPHIX BAS100 vehicle battery tester working temperature: -20°C~65°C (-4°F~140°F), storage temperature: -20°C~70°C (-4°F~158°F). |
