|
|
|
|
|
|
|
|
|
|
*Compatibility Chart
1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).
2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.
3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).
For Audi TT MKII TTS TTRS FWD Quattro 2007-2015
For Audi A3 S3 2009-2013
Important Fitment Notes(Must Read):
Models only For FWD, Equipped with Magnetic Ride Control
*Air Suspension Structure:
*Generation & Evolution:
Audi TT
MK1 First generation (Type 8N; 1998-2006)
MK2 Second generation (Type 8J; 2006-2014)
MK3 Third generation (Type FV /8S; 2014-2023)
Audi A3 S3
First generation (Type 8L; 1996-2003)
Second generation (Type 8P; 2003-2013)
Third generation (Type 8V; 2013-2020)
Fourth generation (Type 8Y; 2020–present)
*Removal Guideline:
Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
Consult your vehicle owner's manual,service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
Once the vehicle has been raised from the ground, put vehicle in neutral, and then back into park to release the tension on the drivetrain.
1.Raise vehicle.
2.Remove applicable rear wheel.
3.Inthetrunk, remove the spare wheel cover and applicable side trim.
4.Disconnect the struts electrical connection.
5.Using a wrench, disconnect the air line from the check valve.
6.Remove the air line fitting from the air hose and discard.
7.Removethe four (4) air strut mounting nuts.
8.Loosen and removethe lower sway bar end link nut then disconnect end link.
9.Detach the rear tie rod.
10.Removethe lower air strut mounting bolt.
11.Remove strut from vehicle.
12.Removal complete.
*Installation Guideline:
Tighten all nuts and bolts to manufacturer's specifications during the installation process.
Do not remove the air fitting from the air strut. Doing so may cause damage and/or void warranty. Remove the white shipping pin from the new air fitting and insert the air line until fully seated.
1.Prepare the air strut by removing the black threaded plastic plug from the valve on the air strut as demonstrated below.
2.Install strut into vehicle.
3.Install lower strut mounting bolt and tighten to manufacturer’s specifications.
4.Installtie rod bolt/nut andtightento manufacturer's specifications.
5.Install sway bar end link/nut andtightento manufacturer's specifications.
6.Lowerthe vehicleto appropriate height and reinstallthe four (4)top mount nuts. tightento manufacturer's specifications.
7.Install the air fitting provided in the kit to existing air hose using the figure below as an example.
8.Reconnect the struts electrical connection.
9.Reinstall all applicabletrunk lining and sparetire cover.
10.Reinstall applicable rear wheel.
11.Lowerthe vehicle.
12.Installation complete.
*Frequently Asked Questions:
How to prevent the damage of air springs/How to extend the service life of air springs/struts etc.?
An air strut with separable air springs
If your vehicle offers a separable air suspension (Audi Allroad A6 C5, Mercedes-Benz W164, BMW X5, etc.), you should regularly (about once a week) lift the car to the maximum position, and remove dirt with a high-pressure cleaner (keep the cleaner at a distance to the air spring about 30 cm/12 inches, otherwise water pressure can damage the air spring). The highest position may vary depending on your model and regulation options. Therefore, please test this by trying the different modes available to you (Sport, comfort, dynamic, off-road) and choose the one that sets your vehicle to the highest position. The dirt will most likely be found under the fold of the pneumatic chambers. If you find a frozen layer of bitumen on the piston guide (the part of a strut on which the air spring is installed), it is recommended to clean it as well. Whenever possible, avoid riding on fresh asphalt, as fresh bitumen mixed with sand immediately results in a build-up of abrasives on the piston and in turn contributes to accelerated wear and tear of the air spring.
A complete air suspension shock
Many cars such as Mercedes W220 or W211 are set up with a complete air strut - shock absorber and air spring visually form a complete spare part. In many cases, you can easily recognize these by the metal cups with which the air spring is tightly mounted. To best avoid any damage, we highly recommend to regularly check the condition of the dust protection seals of the air strut.
What is the difference between an air spring and an air strut?
The air spring is a part of the air strut. Some vehicles (e.g. Mercedes ML) allow you to change the air spring separately. At our online shop you have the opportunity to buy either the whole air strut or only the air spring. For some type of vehicles it is not possible to change the air spring separately. In this case the whole air strut should be replaced.
Which side of my car is the Right and Left?
The right and left sides of an automobile are determined as if sitting in the car facing forward. Thus, the left side is on the left when sitting in the car facing forward, and the right side is on the right. For American cars, the driver’s side is on the left, and the passenger sits to the right of the driver. For cars in Japan, Britain, Ireland, the Bahamas and some other former British colonies -- where they drive on the left side of the road -- the passenger sits on the left side, and the driver (along with all the driving controls) is on the right.
*OEM Part Number:
8J0413029M, 8J0413029D, 8J0413029E, 8J0413029A, 8P0413029，8P0413029B
8J0413030M, 8J0413029L, 8J0413029G, 8J0413029N, 8P0413029C, 8J0413029F
8J0 513 025
8J0 513 025 A
8J0 513 025 B
8J0 513 025 E
8J0 513 025 F
8J0513025
8J0513025A
8J0513025B
8J0513025E
8J0513025F
8J0-513-025-E
*Item Specifications:
- Key Words: 4PCS Front Rear Shock Absorbers Magnetic For Audi TT TTS TTRS MKII 2007-15 A3 S3
- Package Includes:4PCS for Front Rear Shock Absorber Magnetic Ride
Notes: Please double confirm the compatibility as well as the OEM number before purchasing.
*Compatibility Chart
1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).
2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.
3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).
For Audi TT MKII TTS TTRS FWD Quattro 2007-2015
For Audi A3 S3 2009-2013
Important Fitment Notes(Must Read):
Models only For FWD, Equipped with Magnetic Ride Control
*Air Suspension Structure:
*Generation & Evolution:
Audi TT
MK1 First generation (Type 8N; 1998-2006)
MK2 Second generation (Type 8J; 2006-2014)
MK3 Third generation (Type FV /8S; 2014-2023)
Audi A3 S3
First generation (Type 8L; 1996-2003)
Second generation (Type 8P; 2003-2013)
Third generation (Type 8V; 2013-2020)
Fourth generation (Type 8Y; 2020–present)
*Removal Guideline:
Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
Consult your vehicle owner's manual,service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
Once the vehicle has been raised from the ground, put vehicle in neutral, and then back into park to release the tension on the drivetrain.
1.Raise vehicle.
2.Remove applicable rear wheel.
3.Inthetrunk, remove the spare wheel cover and applicable side trim.
4.Disconnect the struts electrical connection.
5.Using a wrench, disconnect the air line from the check valve.
6.Remove the air line fitting from the air hose and discard.
7.Removethe four (4) air strut mounting nuts.
8.Loosen and removethe lower sway bar end link nut then disconnect end link.
9.Detach the rear tie rod.
10.Removethe lower air strut mounting bolt.
11.Remove strut from vehicle.
12.Removal complete.
*Installation Guideline:
Tighten all nuts and bolts to manufacturer's specifications during the installation process.
Do not remove the air fitting from the air strut. Doing so may cause damage and/or void warranty. Remove the white shipping pin from the new air fitting and insert the air line until fully seated.
1.Prepare the air strut by removing the black threaded plastic plug from the valve on the air strut as demonstrated below.
2.Install strut into vehicle.
3.Install lower strut mounting bolt and tighten to manufacturer’s specifications.
4.Installtie rod bolt/nut andtightento manufacturer's specifications.
5.Install sway bar end link/nut andtightento manufacturer's specifications.
6.Lowerthe vehicleto appropriate height and reinstallthe four (4)top mount nuts. tightento manufacturer's specifications.
7.Install the air fitting provided in the kit to existing air hose using the figure below as an example.
8.Reconnect the struts electrical connection.
9.Reinstall all applicabletrunk lining and sparetire cover.
10.Reinstall applicable rear wheel.
11.Lowerthe vehicle.
12.Installation complete.
*Frequently Asked Questions:
How to prevent the damage of air springs/How to extend the service life of air springs/struts etc.?
An air strut with separable air springs
If your vehicle offers a separable air suspension (Audi Allroad A6 C5, Mercedes-Benz W164, BMW X5, etc.), you should regularly (about once a week) lift the car to the maximum position, and remove dirt with a high-pressure cleaner (keep the cleaner at a distance to the air spring about 30 cm/12 inches, otherwise water pressure can damage the air spring). The highest position may vary depending on your model and regulation options. Therefore, please test this by trying the different modes available to you (Sport, comfort, dynamic, off-road) and choose the one that sets your vehicle to the highest position. The dirt will most likely be found under the fold of the pneumatic chambers. If you find a frozen layer of bitumen on the piston guide (the part of a strut on which the air spring is installed), it is recommended to clean it as well. Whenever possible, avoid riding on fresh asphalt, as fresh bitumen mixed with sand immediately results in a build-up of abrasives on the piston and in turn contributes to accelerated wear and tear of the air spring.
A complete air suspension shock
Many cars such as Mercedes W220 or W211 are set up with a complete air strut - shock absorber and air spring visually form a complete spare part. In many cases, you can easily recognize these by the metal cups with which the air spring is tightly mounted. To best avoid any damage, we highly recommend to regularly check the condition of the dust protection seals of the air strut.
What is the difference between an air spring and an air strut?
The air spring is a part of the air strut. Some vehicles (e.g. Mercedes ML) allow you to change the air spring separately. At our online shop you have the opportunity to buy either the whole air strut or only the air spring. For some type of vehicles it is not possible to change the air spring separately. In this case the whole air strut should be replaced.
Which side of my car is the Right and Left?
The right and left sides of an automobile are determined as if sitting in the car facing forward. Thus, the left side is on the left when sitting in the car facing forward, and the right side is on the right. For American cars, the driver’s side is on the left, and the passenger sits to the right of the driver. For cars in Japan, Britain, Ireland, the Bahamas and some other former British colonies -- where they drive on the left side of the road -- the passenger sits on the left side, and the driver (along with all the driving controls) is on the right.
*OEM Part Number:
8J0413029M, 8J0413029D, 8J0413029E, 8J0413029A, 8P0413029，8P0413029B
8J0413030M, 8J0413029L, 8J0413029G, 8J0413029N, 8P0413029C, 8J0413029F
8J0 513 025
8J0 513 025 A
8J0 513 025 B
8J0 513 025 E
8J0 513 025 F
8J0513025
8J0513025A
8J0513025B
8J0513025E
8J0513025F
8J0-513-025-E
*Item Specifications:
- Key Words: 4PCS Front Rear Shock Absorbers Magnetic For Audi TT TTS TTRS MKII 2007-15 A3 S3
- Package Includes:4PCS for Front Rear Shock Absorber Magnetic Ride
Notes: Please double confirm the compatibility as well as the OEM number before purchasing.
| Item Specifics | |
|---|---|
| Brand | Scitoo |
| Placement on Vehicle | Front Rear Left Right |
| Manufacturer Warranty | 1 Years |
| Shock Absorber Type | Magnetic Ride control |
| Product Type | Magnetic Ride Shock Absorber |
| Fitment Type | Direct Replacement |
| Package Included | 4X Front Rear Left Right Shock absorbers Struts |
| Fitment 1 | Fit Audi TT TTS FWD Quattro |
| Fitment 2 | Fit Audi TT MKII TTRS |
| Operating Mode | Magnetic Ride |
| Part Type | Shock Absorber |
| Items Included | Shock |
| Type | Shock Set |
| Shock Absorber System | Double Pipe |
| Advantage 1 | Manufactured with OE Cores and Components |
| Advantage 2 | Equipped with Magnetic Ride Control |
| Features | 100% Accuracy of Fit Adjustable Easy to Replace Greasable |
| Superseded Part Number | 8J0413029M 8J0413029D 8J0413029E 8J0413029A 8J0413030M 8J0513030Q 8J0413029L 8J0413029G 8J0413029N 8P0413029C 8J0413029F 8P0413029 8P0413029B |
| OE/OEM Part Number | 8J0413029M 8J0413029D 8J0413029E 8J0413029A 8J0413030M 8J0513030Q 8J0413029L 8J0413029G 8J0413029N 8J0513025 |
| Interchange Part Number | 8J0513025 8J0513025A 8J0513025B 8J0513025E 8J0513025F |
| Number in Pack | 4PCS |
| Manufacturer Part Number | CB847003S01 |
| Adjustable | Yes |
| OE Spec or Performance/Custom | OE Spec |
| Greasable or Sealed | Sealed |
| Custom Bundle | yes |
| Drive Layout | FWD |
| Return Policy | 30 Days Free Return Or Exchange |
| Included Install Hardware | None |
| Handling Time | 1 days |
| Platform | MKII |
| Surface Finish | Rust Protected |
| Note | No Instruction Included |
| Kit or Single Part | KIT |
| Quantity Sold | Sold individually Or Wholesale |
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
1.We accept multiple payment methods, such as VISA, Master Card, etc..
2.Please do not use the note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as auction ended or order might be delayed.
We stand behind every product we sell.
All of our brand new items come with a 30-Days money-back or exchange guarantee.
Q: How do I pay for my purchase?
A: MY store accepts VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave a feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category New List Item
Hot Item
Warranty
|
Pair Front Shock Absorbers Magnetic Ride For Audi TT TTS TTRS Quattro 2007-2015
*Compatibility Chart 1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number). 2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits. 3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).
For Audi TT MKII TTS TTRS FWD Quattro 2007-2015
Important Fitment Notes(Must Read): Models only For FWD, Equipped with Magnetic Ride Control
*Air Suspension Structure:
*Generation & Evolution: Audi TT MK1 First generation (Type 8N; 1998-2006) MK2 Second generation (Type 8J; 2006-2014) MK3 Third generation (Type FV /8S; 2014-2023)
Audi A3 S3 First generation (Type 8L; 1996-2003) Second generation (Type 8P; 2003-2013) Third generation (Type 8V; 2013-2020) Fourth generation (Type 8Y; 2020–present)
*Removal Guideline: Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence. To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery. Consult your vehicle owner's manual,service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur. Once the vehicle has been raised from the ground, put vehicle in neutral, and then back into park to release the tension on the drivetrain. 1.Raise vehicle. 2.Remove applicable rear wheel. 3.Inthetrunk, remove the spare wheel cover and applicable side trim. 4.Disconnect the struts electrical connection. 5.Using a wrench, disconnect the air line from the check valve. 6.Remove the air line fitting from the air hose and discard. 7.Removethe four (4) air strut mounting nuts. 8.Loosen and removethe lower sway bar end link nut then disconnect end link. 9.Detach the rear tie rod. 10.Removethe lower air strut mounting bolt. 11.Remove strut from vehicle. 12.Removal complete.
*Installation Guideline: Tighten all nuts and bolts to manufacturer's specifications during the installation process. Do not remove the air fitting from the air strut. Doing so may cause damage and/or void warranty. Remove the white shipping pin from the new air fitting and insert the air line until fully seated. 1.Prepare the air strut by removing the black threaded plastic plug from the valve on the air strut as demonstrated below. 2.Install strut into vehicle. 3.Install lower strut mounting bolt and tighten to manufacturer’s specifications. 4.Installtie rod bolt/nut andtightento manufacturer's specifications. 5.Install sway bar end link/nut andtightento manufacturer's specifications. 6.Lowerthe vehicleto appropriate height and reinstallthe four (4)top mount nuts. tightento manufacturer's specifications. 7.Install the air fitting provided in the kit to existing air hose using the figure below as an example. 8.Reconnect the struts electrical connection. 9.Reinstall all applicabletrunk lining and sparetire cover. 10.Reinstall applicable rear wheel. 11.Lowerthe vehicle. 12.Installation complete.
*Frequently Asked Questions: A complete air suspension shock
What is the difference between an air spring and an air strut? The air spring is a part of the air strut. Some vehicles (e.g. Mercedes ML) allow you to change the air spring separately. At our online shop you have the opportunity to buy either the whole air strut or only the air spring. For some type of vehicles it is not possible to change the air spring separately. In this case the whole air strut should be replaced.
Which side of my car is the Right and Left? The right and left sides of an automobile are determined as if sitting in the car facing forward. Thus, the left side is on the left when sitting in the car facing forward, and the right side is on the right. For American cars, the driver’s side is on the left, and the passenger sits to the right of the driver. For cars in Japan, Britain, Ireland, the Bahamas and some other former British colonies -- where they drive on the left side of the road -- the passenger sits on the left side, and the driver (along with all the driving controls) is on the right.
*OEM Part Number: 8J0413029M, 8J0413029D, 8J0413029E, 8J0413029A, 8P0413029，8P0413029B
8J0 513 025
*Item Specifications:
Notes: Please double confirm the compatibility as well as the OEM number before purchasing. Shipping
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. Payment
1.We accept multiple payment methods, such as VISA, Master Card, etc.. 2.Please do not use the note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns
We stand behind every product we sell. Customer Services
Q: How do I pay for my purchase? Feedback
1. We will leave a feedback once we get your payment. Copyright of SCITOO-AutoParts . All rights reserved. |
