Item Description
  • Internal Circlip are the most common type of circlip for bores with grooves. The circlip has a large free diameter and gap width, consequently it fits more tightly into the groove and provides higher and more uniform thrust load capacity. Lugs with holes are provided for rapid fitting or removal with circlip pliers
  • Applications: They are often found in applications that require a part to turn, spin or pivot, and are used within electric motors, turbines, pistons, electronics and many other areas that require bearings. Circlips help to solve problems such as clearance diameter, tolerance take-up and thrust load capacities
  • Material / Coating: Stainless Steel G420 is a general purpose basic high hardenability martensitic steel with higher strength, hardness and wear resistance than G410. This is generally used for cutlery and surgical instruments, valves, gears, shafts, cams, shear blades, etc. Under hardened conditions, G420 steels are resistant to fresh water, alkalis, air, foods and mild acids. The corrosion resistance of G420; however, is lower than that of G410, G316 and G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
  • Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and�corrosion can occur if the material is installed or handled incorrectly.�The use of�tools and drills made from conventional steel�during the installation of�stainless steel fasteners�may also lead to problems. Even the hardest of tools can produce debris that�leaves minute steel particles on the stainless steel fastener surfaces�or in pre-drilled holes. It is these particles that�often�rust when exposed to moisture or oxygen and can result in a stained or tarnished finish�to the stainless steel material
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
  • Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
  • Photos: All photos are for illustration purpose only. Actual product or packaging may vary due to product enhancement
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Fastener Kits Online is not responsible for any loss, claim or damages arising therefrom. In developing this information, Fastener Kits Online has made a determined effort to present it accurately
  • Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
  • Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
  • Internal Circlip are the most common type of circlip for bores with grooves. The circlip has a large free diameter and gap width, consequently it fits more tightly into the groove and provides higher and more uniform thrust load capacity. Lugs with holes are provided for rapid fitting or removal with circlip pliers
  • Applications: They are often found in applications that require a part to turn, spin or pivot, and are used within electric motors, turbines, pistons, electronics and many other areas that require bearings. Circlips help to solve problems such as clearance diameter, tolerance take-up and thrust load capacities
  • Material / Coating: Stainless Steel G420 is a general purpose basic high hardenability martensitic steel with higher strength, hardness and wear resistance than G410. This is generally used for cutlery and surgical instruments, valves, gears, shafts, cams, shear blades, etc. Under hardened conditions, G420 steels are resistant to fresh water, alkalis, air, foods and mild acids. The corrosion resistance of G420; however, is lower than that of G410, G316 and G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
  • Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and�corrosion can occur if the material is installed or handled incorrectly.�The use of�tools and drills made from conventional steel�during the installation of�stainless steel fasteners�may also lead to problems. Even the hardest of tools can produce debris that�leaves minute steel particles on the stainless steel fastener surfaces�or in pre-drilled holes. It is these particles that�often�rust when exposed to moisture or oxygen and can result in a stained or tarnished finish�to the stainless steel material
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
  • Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
  • Photos: All photos are for illustration purpose only. Actual product or packaging may vary due to product enhancement
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Fastener Kits Online is not responsible for any loss, claim or damages arising therefrom. In developing this information, Fastener Kits Online has made a determined effort to present it accurately
  • Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
  • Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
Specification 
ProductInternal Circlip
Size42mm
Closest Size in Imperial1-5/8"
System of MeasurementMetric
Bore Diameter42.00mm
Groove Size G44.50mm
Groove Width1.90mm
Thickness T1.75mm
Circlip Outside Diameter D45.50mm
Hole Size Min D52.50mm
Lug Height Max A5.90mm
Max Ring Dia B4.10mm
MaterialStainless Steel
GradeG420
Corrosion Protection LevelVery Good
FinishStainless G420
StandardDIN 472
BrandInox World
Alternative BrandsBolt and Nut Australia
MPNICLA2M42
DeliveryFree Shipping
Number in Pack300
ebay listing template design by dZine-hub