Throttle Body For 2007-2016 Jeep Patriot 2007-2012 Dodge Caliber 1.8L 2.0L 2.4L
 
ONE YEAR WARRANTY
 
 
 
Specification: 
Modified Item: No
Material: Aluminum
Surface Finish: White
Bundle Listing: Yes
Size: Standard
Fitment Type: Direct Replacement
Mounting Hardware Included: Yes
 
 
Features:
100% brand new and high quality Throttle body
Interchange Part number: 04891735AC, 4891735AB, 4891735AA, 4891735
Replace for OEM number: 04891735AC, 4884551AA
The electronic throttle unit opens and closes the throttle blade based on input from various engine control sensors, including the accelerator pedal
 
Fitment:
2007-2016 JEEP PATRIOT WITH 1.8L 2.0L 2.4L
2007-2016 JEEP COMPASS WITH 1.8L 2.0L 2.4L
2007-2012 DODGE CALIBER WITH 1.8L 2.0L 2.4L
2008-2014 DODGE AVENGER WITH 1.8L 2.0L 2.4L
2009-2016 DODGE JOURNEY WITH 1.8L 2.0L 2.4L
2011-2016 CHRYSLER 200 WITH 1.8L 2.0L 2.4L
For exact years and models, please check compatibilities
 
 
Package includes:
1 x Throttle body
Hardware as shown in the picture above
 
 
Things you'll need
1. Common screwdriver
2. Set of ¼-inch sockets
3. ¼-inch ratchet
4. Needle nose pliers
 
 
Installation:
Step 1: Remove the air cleaner and duct hose assembly using the common screwdriver. Disconnect the electrical connector on the mass air flow by pulling out the plug. Disconnect the intake air temperature sensor found in the air duct.

Step 2: Disconnect the idle air control on the side of the throttle body by pulling the electrical connector out. Disconnect the throttle position sensor opposite the throttle cable levers.

Step 3: Disconnect the throttle cables by turning the throttle lever on the throttle body all the way open by hand and then removing the now slackened cables from the throttle lever.

Step 4: Remove the heated water hoses from the bottom of the throttle body if there are any (this is vehicle dependent). Use the needle nose pliers to remove the clamps by squeezing the clamps and pulling them off. Pull the hoses off. Not all vehicles have these, although there are a few that do.

Step 5: Remove the four bolts running through the throttle body and into the intake manifold. Use appropriate ¼-inch drive socket and ratchet. Lift the throttle body off the intake manifold. Protect the metal gasket that is in between the throttle body and intake. This gasket must be reused. Install the new throttle body and components in reverse order of removal.
 

· Shipping time: 1-6 business days in USA
· After shipping, the tracking No. available by message
· We ship to eBay address

  No returns are accepted without an RMA number.
· Refund is valid within 60 days after the date delivered
· Refund will be given as money back or replacement
· The money less the freight cost will be refunded due to their own fault
· Item must be returned in original packing same as reached
· Buyers are responsible for the return shipping cost.

· One Year Warranty after receiving
· Buyers pay return and replacement shipping cost
· We will not refund any labor cost

 

Throttle Body For 2007-2016 Jeep Patriot 2007-2012 Dodge Caliber 1.8L 2.0L 2.4L
 
ONE YEAR WARRANTY
 
 
 
Specification: 
Modified Item: No
Material: Aluminum
Surface Finish: White
Bundle Listing: Yes
Size: Standard
Fitment Type: Direct Replacement
Mounting Hardware Included: Yes
 
 
Features:
100% brand new and high quality Throttle body
Interchange Part number: 04891735AC, 4891735AB, 4891735AA, 4891735
Replace for OEM number: 04891735AC, 4884551AA
The electronic throttle unit opens and closes the throttle blade based on input from various engine control sensors, including the accelerator pedal
 
Fitment:
2007-2016 JEEP PATRIOT WITH 1.8L 2.0L 2.4L
2007-2016 JEEP COMPASS WITH 1.8L 2.0L 2.4L
2007-2012 DODGE CALIBER WITH 1.8L 2.0L 2.4L
2008-2014 DODGE AVENGER WITH 1.8L 2.0L 2.4L
2009-2016 DODGE JOURNEY WITH 1.8L 2.0L 2.4L
2011-2016 CHRYSLER 200 WITH 1.8L 2.0L 2.4L
For exact years and models, please check compatibilities
 
 
Package includes:
1 x Throttle body
Hardware as shown in the picture above
 
 
Things you'll need
1. Common screwdriver
2. Set of ¼-inch sockets
3. ¼-inch ratchet
4. Needle nose pliers
 
 
Installation:
Step 1: Remove the air cleaner and duct hose assembly using the common screwdriver. Disconnect the electrical connector on the mass air flow by pulling out the plug. Disconnect the intake air temperature sensor found in the air duct.

Step 2: Disconnect the idle air control on the side of the throttle body by pulling the electrical connector out. Disconnect the throttle position sensor opposite the throttle cable levers.

Step 3: Disconnect the throttle cables by turning the throttle lever on the throttle body all the way open by hand and then removing the now slackened cables from the throttle lever.

Step 4: Remove the heated water hoses from the bottom of the throttle body if there are any (this is vehicle dependent). Use the needle nose pliers to remove the clamps by squeezing the clamps and pulling them off. Pull the hoses off. Not all vehicles have these, although there are a few that do.

Step 5: Remove the four bolts running through the throttle body and into the intake manifold. Use appropriate ¼-inch drive socket and ratchet. Lift the throttle body off the intake manifold. Protect the metal gasket that is in between the throttle body and intake. This gasket must be reused. Install the new throttle body and components in reverse order of removal.
 

· Shipping time: 1-6 business days in USA
· After shipping, the tracking No. available by message
· We ship to eBay address

  No returns are accepted without an RMA number.
· Refund is valid within 60 days after the date delivered
· Refund will be given as money back or replacement
· The money less the freight cost will be refunded due to their own fault
· Item must be returned in original packing same as reached
· Buyers are responsible for the return shipping cost.

· Buyers pay return and replacement shipping cost
· We will not refund any labor cost

 

On May 15, 2023 at 02:28:40 PDT, seller added the following information:

DataCaciques