FCC ID: OUC6000066

MEMORY DRIVER #1 or #2 1 or 2 

Part #: IC: 580K-600066 THL-55 9U 9RU-0 0749

2008 2009 2010 2011 2012 2013 Cadillac CTS  -  without push button start and without remote start

2008 2009 2010 2011 Cadillac DTS Sedan

FCC ID: OUC6000066

 IC: 850K-6000066 

STRATTEC P/N: 5923878, 5923877

D3100066DC DOM31 5MHz 9A

See Item Specifications for more details

Compatible Vehicle’s

2008 2009 2010 2011 2012 2013 Cadillac CTS  -  without push button start and without remote start

2008 2009 2010 2011 Cadillac DTS Sedan

2008 2009 2010 2011 Cadillac STS Sedan

Programming

2008-2009

.........................................

Use this Procedure for Vehicles with Driver Information Center Buttons

....................................

This information is in your Owner’s Manual in the

Drivers Information Center Section.

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE  displays

4.  Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds.
A chime will sound indicating that the remote is programmed.

5.  To program additional remotes at this time repeat step 3.

 This vehicle can have a maximum of eight remotes programmed.

6.  To exit programming mode turn key off and remove key.

Test remote(s).

...................................

Use this Procedure for Vehicles without Drivers Information Center Buttons

...................................

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine)

1 Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2 Press and hold the trip odometer reset stem for three seconds. The message  REMOTE KEY LEARNING ACTIVE  will display

3.Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds.
A chime will sound indicating that the remote is programmed.

4.To program additional remotes at this time repeat step 3.

This vehicle can have a maximum of eight remotes programmed.

5.To exit programming mode turn key off and remove key.

 Test remote(s).

=======================================

2010 and Later Models

.............................

 You have one working remote and you want to add another.

............................

1. Vehicle must be off.

2. Place the working remote(s) in the cupholder. Have the new remote with you.

3. Insert the key into the key lock cylinder located on the outside of drivers door.

4.Turn the key to the unlock position five times with in five seconds.

5. The (DIC) Driver Information Center displays Ready to Learn Electronic key #2, 3 or 4

6. Place the new remote into the transmitter pocket with the buttons facing the front of the vehicle.
(The transmitter pocket is inside the center console between the driver and front passanger seats).

7. A beep sounds once the remote is programmed. The DIC displays Ready to Learn
Electronoic Key #3 or 4, Or Maximum # Electronic Keys Learned.

8. Press the ignition control knob to exit programming mode.

9. Remove the remote from the transmitter pocket and press unlock to the remote two times.

10. To program additional remotes, repeat Steps 6 through 9.

...................

IF you have no working remotes.

.........................

1. The vehicle must be off.

2. Place the new remote into the transmitter pocket with the buttons facing the front of the vehicle.
(The transmitter pocket is inside the center console between the driver and front passanger seats).

3. Insert the key into the key lock cylinder located on the outside of drivers door.

4.Turn the key to the unlock position five times with in five seconds.

5. The (DIC) Driver Information Center displays Ready to Learn Keys.

6. Press the ignition switch in.

7. The DIC reads Learn Delay Active Wait XX Min and counts down to zero.

8. The DIC displays Press Start Control To Learn Keys again.

9. Press the ignition switch in again.

10. Repeat Steps 7, 8 and 9

11. The DIC reads Learn Delay Active Wait XX Min and counts down to zero.

12. A beep sounds and the DIC reads Ready To Learn Electronic Key # X.  All previously known remote programming has been erased.

13. A beep sounds once programming is complete. The DIC displays Ready To Learn Electronic Key #2

14. To program additional remotes, insert each transmitter in the pocket until a beep is heard and the
 DIC advances to the next electronic key number.
Up to four remotes can be programmed. The DIC dislpays Maximum # Electronic Keys Learned and exits the programming mode.

15. Press the ignition control knob if programming is complete.

16. Press unlock on each newly programmed remote to complete the process.

Additional Information

Please Note : These Vehicles May Come With Many

Different Remotes. Your Remote Must Look Like This

One In Order For It To Work With Your Vehicle, & It Must Have

The Same Buttons. If You Don't Have A Remote To Compare

To, Simply Message Me With Your VIN # And I Will Look Up The Correct Remote For Your Vehicle!

This is a genuine Cadillac remote and will work with the factory remote keyless entry system (RKE) on the cars in the chart above.
Your vehicle must have the factory RKE system on it.
Customers are responsible to determine if they have this option and to purchase the correct remote for their vehicle.
Also, this remote has a  #2 on it indicating the driver memory position. 
There also exists a #1 remote which will work just the same, however, when used it will set the car to the programmed settings for driver #1.