If you're
not sure your vehicle can use this key , please ask questions or contact
your local dealer first.
This key needs to be programmed to your vehicle in order
for it to work with your vehicle
TYPE A
1998-1999 ES300 Key Programming
Key Programming 1. Insert an already programmed master key into the ignition. Do not turn.
2. Press and release the gas pedal 5 times.
3. Press and release the brake pedal 6 times.
4. Remove the key from the ignition.
5. Insert the new key you want to program into the ignition.
6. Press and release the gas pedal one time.
7. Wait 1 minute. The security light will be blinking for this one minute. When it stops blinking your
key is programmed. To end programming step on brake one time.
NOTE: Look for your security light. This light will guide you during
the programming procedure. The security light will go off at Step 1.
It will remain off until Step 6. The security light will come on and
start to blink after Step 6 until the key is programmed. If the
security light comes on after Step 4 STOP the procedure and start over
again.
If you perform this procedure too slowly your car will not go into
programming mode. If you can not get your car to go into programming
mode make sure you are using a master key and not a valet key.
If you have a master key then you will probably need to perform this procedure more quickly.
TYPE B
Lexus Key and Remote Programming
Key Programming 1. Insert an already programmed master key into the ignition. Do not turn.
2. Press and release the gas pedal 5 times.
3. Press and release the brake pedal 6 times.
4. Remove the key from the ignition.
5. Insert the new key you want to program into the ignition.
6. Press and release the gas pedal one time.
7. Wait 1 minute. The security light will be blinking for this one minute. When it stops blinking your
key is programmed. To end programming step on brake one time.
NOTE: Look for your security light. This light will guide you during
the programming procedure. The security light will go off at Step 1.
It will remain off until Step 6. The security light will come on and
start to blink after Step 6 until the key is programmed. If the
security light comes on after Step 4 STOP the procedure and start over
again.
If you perform this procedure too slowly your car will not go into
programming mode. If you can not get your car to go into programming
mode make sure you are using a master key and not a valet key.
If you have a master key then you will probably need to perform this procedure more quickly.
Remote Programming 1. Close and lock all doors. Unlock and open drivers door.
2. Put key into ignition and remove. Do not turn it on.
3. Using the electric lock switch. Lock and unlock 5 times. (Lock,
Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock)
4. Close and open drivers door.
5. Using the electric lock switch. Lock and unlock 5 times. (Lock,
Unlock, Lock, Unlock, Lock, Unlock,Lock, Unlock, Lock, Unlock)
6. Put key into ignition. Turn to "ON" , turn off and remove.
7. You will see the door locks cycle by themselves.
If the door locks do not cycle (lock and unlock) by themselves then the car isn’t in programming mode and you must start over.
8. On the remote, press and hold the LOCK and the UNLOCK button at the same time for no more than 2 seconds.
9. On the remote, press the LOCK button for no more than 1 second.
AT THIS POINT, the locks should cycle by themselves ONE time. This means the procedure was accepted.
IF the locks cycle twice it has failed.
The most common reason for programming failure is because the car
didn’t receive a good signal from the remote. To fix this problem try
these tips. 1) Stand outside of the car while you are performing steps 8
and 9. 2) Don’t hold the remote buttons down as long.
As long as the car is still in programming mode you can keep trying
steps 8 and 9 until you complete the programming. If you wait too long
and the car exits the programming mode then you must start over.
After you get the remote to program then continue on with step 10.
10. Close and open door to end programming procedure.
TYPE C
Lexus Key and Remote Programming Instructions
Key Programming
1. Insert an already programmed master key into the ignition. Do not turn.
2. Press and release the gas pedal 5 times.
3. Press and release the brake pedal 6 times.
4. Remove the key from the ignition.
5. Insert the new key you want to program into the ignition.
6. Press and release the gas pedal one time.
7. Wait 1 minute. The security light will be blinking for this one minute. When it stops blinking your
key is programmed. To end programming step on brake one time.
NOTE: Look for your security light. This light will guide you during
the programming procedure. The security light will go off at Step 1.
It will remain off until Step 6. The security light will come on and
start to blink after Step 6 until the key is programmed. If the
security light comes on after Step 4 STOP the procedure and start over
again.
If you perform this procedure too slowly your car will not go into
programming mode. If you can not get your car to go into programming
mode make sure you are using a master key and not a valet key.
If you have a master key then you will probably need to perform this procedure more quickly.
Remote Programming
1. Close and lock all doors. Unlock and open drivers door.
2. Put key into ignition and remove TWO TIMES.
3. Close and open the drivers door TWO TIMES.
4. Put key into the ignition and remove.
5. Close and open the drivers door two times.
6. Put key into the ignition. Close the drivers door.
7. Turn ignition ON then OFF ONE TIME- this will put the car in ADD mode for your remote. (Turning
the ignition ON then OFF TWO TIMES will ADD the remote but will erase all existing remotes.)
8. Remove the key from the ignition. The door locks will cycle one time (or two if you are erasing) .
On the REMOTE press and hold the LOCK and the UNLOCK button for 2 seconds. On the REMOTE press the LOCK button for one second.
AT THIS POINT, the locks should cycle by themselves ONE time. This
means the procedure was accepted. IF the locks cycle twice it has
failed. IF this happens you must start over. Hold the remotes higher up
for better reception
9. Open and close the drivers door. Put key in ignition and pull out. This will end programming.
TYPE D
Lexus Key and Remote Programming Instructions
Key Programming
You can not program this key yourself. You will need to take your
car and key to either the dealer or to a local locksmith that has the
Lexus programming software
TYPE E
Lexus Key and Remote Programming Instructions
Key Programming
1. Close all doors.
2. Insert an already programmed master key into the ignition.
3. Turn the key in the ignition ON and OFF FIVE (5) times.
4. Open and close the drivers door SIX (6) times.
5. Remove the key from the ignition.
6. Insert the new key you want to program into the ignition.
7. Wait up to 2 minutes. The security light will be blinking for up to 2
minutes. When it stops blinking your key is programmed. To end
programming step on the brake one time.
NOTE: You have 35 seconds to complete steps 1-5 and 10 seconds to
complete step 6. If you do not do this procedure fast enough the car
will not go into programming mode and your key will not program.
If the security light does not go out after 2 minutes start the procedure over again.
If you need to erase existing keys, in the case of stolen or missing
keys, follow the procedure below. This will erase all keys except for
the master key you use during this procedure.
1. Close all doors.
2. Insert an already programmed master key into the ignition.
3. Turn the key in the ignition ON and OFF SIX (6) times.
4. Open and close the drivers door SEVEN (7) times.
5. Remove the key from the ignition.
I recommend doing this procedure a couple of times to make sure it takes.
Remote Programming
1. Close and lock all doors. Unlock and open drivers door.
2. Put key into ignition and remove TWO TIMES.
3. Close and open the drivers door TWO TIMES.
4. Put key into the ignition and remove.
5. Close and open the drivers door two times.
6. Put key into the ignition. Close the drivers door.
7. Turn ignition ON then OFF ONE TIME- this will put the car in ADD mode
for your remote. (Turning the ignition ON then OFF TWO TIMES will ADD
the remote but will erase all existing remotes.)
8. Remove the key from the ignition. The door locks will cycle one time
(or two if you are erasing) . On the REMOTE press and hold the LOCK and
the UNLOCK button for 2 seconds. On the REMOTE press the LOCK button for
one second.
AT THIS POINT, the locks should cycle by themselves ONE time. This
means the procedure was accepted. IF the locks cycle twice it has
failed. IF this happens you must start over. Hold the remotes higher up
for better reception
9. Open and close the drivers door. Put key in ignition and pull out. This will end programming.
How to find out if this remote is
compatible with your Vehicles’ installed RKE System
If you're not sure your vehicle can use this
remote, please ask questions or contact
1 of 2Loading...Secure transaction
