eBay

This item is pre-owned – it will work like new once programmed to your vehicle

ONE (1)

OEM FACTORY ORIGINAL AUTHENTIC

Aftermarket remote keyless entry fob alarm

Transmitter control clicker keyfob controller replacement

Keyfob fab keyfab phob keyphob controller clicker

Beeper car starter engine start vehicle door opener trunk release

Functions at 100% Tested & Guaranteed

Directed Electronics Inc. (DEI)

Avital

FCC ID: EZSDEI474S

Alternate Spelling: EZSDE1474S

FCC ID EZSDEI474S

EZS-DEI474S, EZS DEI474S, EZSDEI474S, EZSDE1474S, EZSDEI4745, EZ5DEI4745

DEI Headquarters, Inc. Sidewinder Transmitter DEI474S

Interchangeable FCC IDs:

EZSDEI474

EZSDEI474S

Part #: 7143L

Interchangeable Part #s:

470	474	475	476	485
820041	7143	26131	SAA474U

Frequency: 433 – 434 MHz

LED color: Green

3 buttons Lock Unlock Car Starter Trunk Release Door Opener

Battery: (1) CR 2032 CR2032

Please Note:A Valet / Programming switch is required to program this remote.

Programming can be difficult if you are not familiar with it. Please read the programming instructions (below) before purchasing. Assistance from an auto specialty shop or locksmith may be needed.

Compatible w/ the following systems: Avital 7143L is compatible with the following systems: Automate 410A, 425A, 435A, 552A, 553A, AM2, AM5, AM6, AM7, AM9, Avital 21000, 2200, 4000, 4100, 4200, 4300, 4400, Python 440 HP, 460 HP, 660 XP, Sidewinder 381S, 3200 HS, 3300 HS, 5500 XS, Valet 554T, 562T, 561R, 563T, 712T, 716T, Hornet 740, 742, Rattler 110D, 210D, 310D, 369D, Viper 210 HV, 350 HV, 650 XV, 850 XV. The RPN 7143L remote can be used to replace 474V, 474T, 474L, 474P. Those would be the Viper, Valet, Avital, and Python Versions of the same remote. There is also the 3 button group of remotes 473T, 473S, 473P, 473V, 473L, 7133L which can also be replaced by this 474A. Also the 2 button remotes with RPN 471T and 471C are replaceable using the 7143L. The remote comes with the battery already inside and free programming instructions are included. The FCC ID on this remote is EZSDEI474V but depending on the brand of your old remote, it could be EZSDEI474P or EZSDEI474S. This is a 433-434 MHz remote with 4 buttons and a green LED. Please Note: compatible with any DEI remote that has a flashing green light and ends with a FCC# EZSDEI 470, 471, 474, 475, 476 or 485. Some older key fob transmitter remote original cases may also have the following: FCC ID: EZSDEI470 FCC ID: EZSDEI471 FCC ID: EZSDEI474 FCC ID: EZSDEI475 FCC ID: EZSDEI476 FCC ID: EZSDEI485 FCC ID: EZSDEI7143 Programming instructions are included with this remote.
Automate 6 7 10 25 35 410 425 435 52 53 552 553	Avital 2100 2200 2300 3100 3200 3300 4000 4100 4200 4300 4400 Maxx2 Maxx3	Hornet 533 T 554 T 740 T 742 T 851 T	Python 400 HP 440 HP 450 ESP 460 HP 500 HP 625 HF 650 ESP 660 XP 700 900 1000 HF PC 1000 HF 1200 XP 1400 XP 1500 HF 1600 XP 2000 HF 3000 HF 3000 ESP	Sidewinder 3000 HF 3000 ESP 3200 HS 3300 HS 3500 ESP 4500 HF 5000 HF 5000 ESP 5500 XS 6000 HF 6000 ESP 6500 HF 6500 ESP 7000 HF 7000 ESP PC 7000 SHF	Rattler 100 110 D 200 210 D 250 259 R 300 310 D 359 R 369 D	Valet 450 R 519 H 551 R 552 T 562 T 561 R 712 T 716 T	Merlin 2000

Viper

100 HF (ESP)

130 HV

150 ESP

160 XV

210 HV

211 HV

300 HF

PC 300 HF (ESP)

300+ HF

330 V

350 HV

500 HF

PC 500 HF (ESP)

550 HF

550 HF (ESP)

560 XV

571 XV

600 HF

PC 600 HF (ESP)

650 XV

671 XV

700 ESP

771 XV

PC 800 SHF

800 SHF ESP

850 XV

1000

1002

3000

3002

5000

5002

7900

Programming Instructions:

The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use

the following programming routine to add transmitters to the vehicle’s security

system or to change button assignments if desired.

In order to enter Learn Routine, the Valet/Program push button must be plugged

into the main brain's Blue 2 Pin Port (Look for a small black push button located

under the drivers dash or drivers kick panel somewhere).

The Valet/Program switch, plugged into the blue port, is used for programming.

There is a basic sequence of steps to remember whenever programming this unit.

1) Open a door and make sure the dome light is on.

2) Turn the ignition on to the RUN position or you may also start car.

3) Within 10 seconds, press and release the Valet/Program switch the number of

times that corresponds to the desired channel (listed below). Once you have selected

the channel, press the switch once more and HOLD it. The LED will flash and then the

horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch.

CHANNEL #	FUNCTION
1	Arm / Disarm / Panic
2	Silent Mode / Remote Valet / Trunk Release
3	Remote Start or other accessories
4	Arm only (4 button remote)
5	Disarm only (4 button remote)
6	Panic only (4 button remote)
7	Auto Program single Arm – Disarm – Panic button configuration (4 button remote)
8	Auto Program this remote
9	Delete all transmitters
CHANNEL 9: If any transmitter button from a known transmitter is programmed to channel 9, all transmitters will be erased from memory. This is useful in cases when one of the customer’s transmitters is lost or stolen. This will erase any lost or stolen transmitters from your system’s memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly.

4) You can advance from programming one channel to another by releasing

the Valet/Programming switch and tapping it to advance channels and then

HOLDING it.

For instance; you have programmed Channel 1 and you want to program Channel

2. Release the Valet/Program switch. Press it one time and release it to advance

from Channel

1 to Channel

2. Now, press and HOLD the Valet/Program switch.

The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release.

If you want to program Channel 3 after programming Channel 1,

release the Valet/Program switch, press it twice and release it to advance to Channel 3

. Then press it once more and HOLD it. The horn will chirp

3 times (if connected) and the LED will flash 3 times to confirm it is

ready to receive the code from the transmitter.

5) Once the code(s) are learned, the Valet/Program push button can be released.

6) Programming mode will be exited if one of the following actions occurs:

a. Ignition key is turned to the OFF position

b. Valet/Program switch is pressed too many times.

c. More than 15 seconds elapses between programming steps.

The horn will emit one long chirp when programming mode has been exited.

100% Guarantee Remote Shipping / Return Policy

Warranty/Returns:

1. We have a 30 day return policy.

2. All returns for replacements and refund need an RMA #.

3. Please contact us before returning items so we can give you the RMA # and the proper return address.

We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

Does this keyless remote entry come with a battery?

Yes. It will have a working battery installed.

Battery Condition:

A. All remotes sold on Keyless4u include working batteries.

B. Installed batteries are not tested for battery life- they are simply working.

Some are new and some are used.

Your vehicle will be installed with one of the following keyless entry systems:

a. Standard Keyless Remote Packages: Installed at time of manufacture.

b. Optional Keyless Remote Packages: Installed by a dealer.

c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop.

d. No remote keyless entry system at all.

The above information can change which remote you need
for your installed remote keyless system.