| 1:1（820） | 2:1（Fast Curing） | 2:1（Slow Curing） | 3:1（806） | UV Resin | Liquid Mold Silicone | |
| Ratio | By volume A:B=1:1 |
By weight A:B=2:1 By volume A:B=1.7:1 |
By weight A:B=2:1 By volume A:B=1.7:1 |
By weight A:B=3:1 By volume A:B=2.5:1 |
No proportioning required | By weight A:B=1:1 |
| Specifications | 200ml 400ml 500ml 600ml 1000ml 2L 4L=2L*2 |
300g 750g 1.5kg 3kg 6kg=3kg*2 9kg=3kg*3 |
300g 750g 1.5kg 3kg 6kg=3kg*2 9kg=3kg*3 |
400g 680g 1kg 4kg 8kg=4kg*2 |
100g 200g 250g 500g |
1kg
2kg
|
| Reference temperature | 25℃ | 18℃ | 18℃ | 25℃ | UV lamp lighting | 25℃ |
| Reference thickness | 2CM-3CM | 2CM | 2-4CM | 2CM-5CM | 5MM | / |
| Working Time | 1-2 Hours | 10 Minutes | 1-2 Hours | 1-2 Hours | 1-2 Minutes | 30 Minutes |
| Curing Time | 8-24 Hours | 40 Minutes | 24-48 Hours | 24-48 Hours | 2-10 Minutes | 3-4 Hours |
Note:
2:1 is a mixing ratio by weight. Therefore, all 'L' marked on the listing should default to 'kg'.
The product will be bumped during transportation, so there may be some errors in all specification, but this does not affect use. If you mind, please buy with caution.
It is recommended to purchase enough at one time to affect the production of your project.
Any questions please feel free to contact us.
It is recommended to purchase enough at one time to affect the production of your project.
Any questions please feel free to contact us.
Fast Cure VS Slow Cure:
If you want to make a thicker and larger river table, choose a slow curing resin, which is easier to work with.
Rapid curing has relatively high requirements for operation, and it needs a small amount of multiple attempts before it can be used in large quantities.
If you want to make a thicker and larger river table, choose a slow curing resin, which is easier to work with.
Rapid curing has relatively high requirements for operation, and it needs a small amount of multiple attempts before it can be used in large quantities.
The curing time of fast curing is very short, 40 minutes curing, and the operation requirements are high, please try a small amount in advance, and use it in large quantities after mastering the skills!!
Kind Tips:
If some large bottles of resin are sold out. We may replace them with multiple sets of small bottles for buyers by default, but the total quantity will not change.
Specific specifications are as follows:
1:1 Resin 4L / 1:1 Resin 2L*2
2:1 Resin 3KG / 2:1 Resin 1.5KG*2
2:1 Resin 6KG / 2:1 Resin 1.5KG*4
2:1 Resin 9KG / 2:1 Resin 1.5KG*6
3:1 Resin 4kg / 3:1 Resin 1kg*4
3:1 Resin 8kg / 3:1 Resin 1kg*8
If you have any questions, please feel free to contact us.
Feature:
Highly transparent, non-yellowing, automatic defoaming.
You can make rings, bracelets, pendants, etc. with our glue.
You can experience the fun of handcrafting and creativity.
Highly transparent, non-yellowing, automatic defoaming.
You can make rings, bracelets, pendants, etc. with our glue.
You can experience the fun of handcrafting and creativity.
Specifications:
Name: 2:1 Epoxy Resin (Fast Curing OR Slow Curing)
Color: Crystal Clear
Material: Resin
Uses: crystal epoxy production, cos equipment production, RC boat production, DIY glass steel works, reinforcement, etc.
Capacity: 1.5KG/3KG/6KG/9KG
Color: Crystal Clear
Material: Resin
Uses: crystal epoxy production, cos equipment production, RC boat production, DIY glass steel works, reinforcement, etc.
Capacity: 1.5KG/3KG/6KG/9KG
Please Note:
As this product is very pure epoxy. Pure Epoxy resin can develop crystals (usually in Part A). This is not from faulty resin but common thought is that it is from the cylic hot days and cold nights when stored.
An easy fix is to heat the jugs up in very hot water for about 30 mins and this will restore the resin to perfectly clear. The heating is also good to help remove air bubbles trapped in the epoxy due to transportation.
As this product is very pure epoxy. Pure Epoxy resin can develop crystals (usually in Part A). This is not from faulty resin but common thought is that it is from the cylic hot days and cold nights when stored.
An easy fix is to heat the jugs up in very hot water for about 30 mins and this will restore the resin to perfectly clear. The heating is also good to help remove air bubbles trapped in the epoxy due to transportation.
Usage:
1. Mixed two bottles: A : B = 2:1 ratio(weight ratio).
2. Stirring must be uniform, especially the inner wall of the container, the bottom, etc., about 5 minutes.
You can use glass rods, bamboo sticks, etc. After mixed,this product is better to let stand for 3-5 minutes
before used in order to break the bubbles which produced when it was mixing in time.
3. Please try a little bit before using the product a lot, so that would master the skills and avoid mistakes.
4. When using crystal glue, be careful not to stick it on your hands or body. If this happens, wipe off the glue with a cloth or paper towel, then rinse with water soap or detergent.
1. Mixed two bottles: A : B = 2:1 ratio(weight ratio).
2. Stirring must be uniform, especially the inner wall of the container, the bottom, etc., about 5 minutes.
You can use glass rods, bamboo sticks, etc. After mixed,this product is better to let stand for 3-5 minutes
before used in order to break the bubbles which produced when it was mixing in time.
3. Please try a little bit before using the product a lot, so that would master the skills and avoid mistakes.
4. When using crystal glue, be careful not to stick it on your hands or body. If this happens, wipe off the glue with a cloth or paper towel, then rinse with water soap or detergent.
Question:
Q:Why are there bubbles in the finished product?
A:Stir too fast when adjusting the glue, and pour into the mold before the bubbles have completely subsided. Or after pouring the glue into the mold, the inner wall of the mold is not observed. If there are bubbles, please cut them off in time.
Q:Why are there bubbles in the finished product?
A:Stir too fast when adjusting the glue, and pour into the mold before the bubbles have completely subsided. Or after pouring the glue into the mold, the inner wall of the mold is not observed. If there are bubbles, please cut them off in time.
Q:Why is the finished product soft?
A:Inaccurate adjustment of the glue ratio will cause the finished product to not solidify, and the glue will not be thoroughly mixed evenly during stirring, and there will be wire drawing in the glue, and the mold will be demolded if it is not completely solidified.
A:Inaccurate adjustment of the glue ratio will cause the finished product to not solidify, and the glue will not be thoroughly mixed evenly during stirring, and there will be wire drawing in the glue, and the mold will be demolded if it is not completely solidified.
Q:What should I do if I get Epoxy?
A:It can be washed directly with water, or wiped with a nail remover towel before washing.
A:It can be washed directly with water, or wiped with a nail remover towel before washing.
Q:What should I do if I get Epoxy?
A:It can be washed directly with water, or wiped with a nail remover towel before washing.
A:It can be washed directly with water, or wiped with a nail remover towel before washing.
Q:Can it be put in the sun or in the refrigerator?
A:Do not expose to the sun for a long time. Excessive exposure to ultraviolet rays will make the finished product fade and yellow. Putting glue in the refrigerator will greatly extend the fixed time.
A:Do not expose to the sun for a long time. Excessive exposure to ultraviolet rays will make the finished product fade and yellow. Putting glue in the refrigerator will greatly extend the fixed time.
Package include:
1 x A Epoxy Resin(1000ML)
1 x B Epoxy Resin(500ML)
OR
1 x A Epoxy Resin(2L)
1 x B Epoxy Resin(1L)
OR
1 x A Epoxy Resin(4L)
1 x B Epoxy Resin(2L)
OR
1 x A Epoxy Resin(6L)
1 x B Epoxy Resin(3L)
1 x A Epoxy Resin(1000ML)
1 x B Epoxy Resin(500ML)
OR
1 x A Epoxy Resin(2L)
1 x B Epoxy Resin(1L)
OR
1 x A Epoxy Resin(4L)
1 x B Epoxy Resin(2L)
OR
1 x A Epoxy Resin(6L)
1 x B Epoxy Resin(3L)
On 09/08/2023 at 20:53:51 AEST, seller added the following information:
On 16/08/2023 at 11:07:28 AEST, seller added the following information:
On 20/09/2023 at 21:35:16 AEST, seller added the following information:
On 02/12/2023 at 15:19:14 AEDT, seller added the following information:
On 13/12/2023 at 22:58:51 AEDT, seller added the following information:
On 04/01/2024 at 10:01:04 AEDT, seller added the following information: