Premium Product Features
- Premium quality & great compatibility
- Simple & quick installation
- Top-grade aftermarket parts
- Reliable after-sales support
- Precision-made for perfect fit
- Great performance & long service life
A starter (also self-starter, cranking motor, or starter motor) is a device used to rotate (crank) an internal-combustion engine so as to initiate the engine's operation under its own power. Starters can be electric, pneumatic, or hydraulic. In the case of very large engines, the starter can even be another internal-combustion engine.
Internal combustion engines are feedback systems, which, once started, rely on the inertia from each cycle to initiate the next cycle. In a four-stroke engine, the third stroke releases energy from the fuel, powering the fourth (exhaust) stroke and also the first two (intake, compression) strokes of the next cycle, as well as powering the engine's external load. To start the first cycle at the beginning of any particular session, the first two strokes must be powered in some other way than from the engine itself. The starter motor is used for this purpose and it is not required once the engine starts running and its feedback loop becomes self-sustaining.
Starter installation
Clean the armature and external drive mechanism with gasoline first. After cleaning, check whether the drive is flexible; when installing, apply graphite grease between the friction plates of the friction clutch, and apply organic oil to the threaded filament part; the starter is installed on the engine, and the distance between the end face of the driving gear and the plane of the flywheel is 3 5 mm is appropriate to ensure that the gears mesh correctly.
Fault check
The starter often has failures and phenomena that cannot rotate or rotate slowly. In this case, check the following aspects:
1. The battery has no electricity or the electricity is weak, so the starter cannot rotate or rotate slowly.
2. The starter thread is loose or off, and the switch or adsorption switch fails.
3. The brush is worn out or the brush surface is not correct, and the spring is weak, resulting in poor contact of the rectifier.
4. Excitation coil or armature coil is short-circuited or disconnected.
5. The rectifier is fouled and the mica sheet is protruding, causing poor contact between the brush and the rectifier.
Organization maintenance
In the process of starting the engine, the starter must draw in 344~400Ah from the battery. Therefore, in order to prevent the battery from over-current or damage, the starting time should not exceed 5s. In winter, it is easy to start difficult to start. Multiple starting times should not be too long, and appropriate intervals should be left in each starting.
Rotation:CW
Teeth:10
Voltage:12
Starter Type:PMGR
Power Rating:1
Number of Holes:2
Chrysler: 56041013AC
Mitsubishi: M000T83381, M000T83381ZC
Lester: 17799
PIC: 103-221
Arrowhead: SMT0152
BBB Ind: 17799
BBB New: N17799
Bosch Remanufactured: SR6439X
Carquest: 17799S
Carquest New: 17799SN
Remy Remanufactured: 17728
J & N Automotive: 410-48229
Denso First Time Fit: 280-4279
MPA: 17799
MPA New: 17799N
NAPA: 244-6834
NAPA Pro Series: 17799
Rayloc: 44-6834, 446834
Rayloc New: 4N6834
Wilson: 91-27-3272
Wilson New: 91-27-3272N
Dixie Electric: S-8980
Mitsubishi Sales: M0T83381, M0T83381ZC
Excel: 2663
Dodge Dakota 2000-2002 L4 2.5L
Jeep TJ 2001 L4 2.5L Manual trans.; To 10/2/2000
Jeep Wrangler 2001 L4 2.5L Manual trans.; To 10/2/2000
Notice
1.Please verify your vehicle's make, model, year and OE number prior to ordering for accurate fitment.
2.Contact us anytime if you need help with fitment or installation.
3.Avoid breakdowns caused by a bad starter! Our high-quality starter offers fast delivery, exact fit and reliable long-lasting performance.
