Dumpling Skin Machine Dumpling Wrapper Maker Small 8cm Mold
Product Parameters
Product Size:58*31*32cm /22.83*12.2*12.59inch
Net Weight:17kg
Voltage：110V
Motor Power 140 Watts
Mold: Φ8cm/3.15inch, 10g
Production Capacity 40 Pieces/Min
Mold Shape: Round Shaped
Description:
This Dumpling Skin Machine Has The Advantages Of Light Weight(Only About 37.5 Lbs), Mold Replaceable, One-Click Mold Replacement, High Efficiency, Energy Saving, Safety And Sanitation, No Corner Scrap,Thick In The Middle And Thin At The Edges, Imitating Hand-Rolling, Etc.
|
|
|
|---|---|---|
Powerful
| Durable
| Safe And Reliable
|
|
|
|
|---|---|---|
Feature:
1.Powerful
High-Power Motor, Strong And Smooth Without Jamming
2.Durable
Safe And Stable, With a Service Life Of More Than 10 Years
3.Safe And Reliable
Motor Enclosed Design To Prevent Leakage Of Electricity Due To Water Ingress
4.One-Click Mold Change
5.Powerful Motor
Low noise, long service life.
Package List:
1*Machine
2*Inner Hexagon Wrench
1*Power Cord
1*Machine Manual
Use of FAQs for analysis and exclusion
1. Fault: The skin is incomplete
Reason analysis: the supply amount is too small
Solution: counterclockwise rotation feed adjustment hand wheel to increase the supply surface
2. Fault: The skin is not smooth with trachoma or hemp spots
Reason analysis: the supply amount is too large
Solution: clockwise rotation feed adjustment hand wheel to reduce the supply surface
3. Fault: the skin is rough and fluffy
Reason analysis: the dough is not kneaded or the dough is too thick
Solution: knead the dough to make a surface block of about 1 cm thick (if the surface shrinkage should be the thinner, the better), the width and the same as the surface entrance.
4. Fault: the skin is short or rolled up
Reason analysis: The dough is too soft
Solution: knead the dough with flour until moderate hardness, or reduce the amount of water.
5. Fault: skin long or skin rolled down
Reason analysis: the dough is strong
Solution: Increase the amount of water appropriately to make the dough dough moderately soft and hard.
6. Fault: The skin can not come out
Cause analysis: The dough is too soft or too sticky
Solution: knead the dough with flour until moderate hardness, or reduce the amount of water. And coat the finished dough pieces with dry flour on both sides.
7、Fault: The face has cracks
Cause analysis: put in oil or salt
Solution: Do not put any salt and oil when flour.
Note:The square mold needs to be customized
1. Fault: The skin is incomplete
Reason analysis: the supply amount is too small
Solution: counterclockwise rotation feed adjustment hand wheel to increase the supply surface
2. Fault: The skin is not smooth with trachoma or hemp spots
Reason analysis: the supply amount is too large
Solution: clockwise rotation feed adjustment hand wheel to reduce the supply surface
3. Fault: the skin is rough and fluffy
Reason analysis: the dough is not kneaded or the dough is too thick
Solution: knead the dough to make a surface block of about 1 cm thick (if the surface shrinkage should be the thinner, the better), the width and the same as the surface entrance.
4. Fault: the skin is short or rolled up
Reason analysis: The dough is too soft
Solution: knead the dough with flour until moderate hardness, or reduce the amount of water.
5. Fault: skin long or skin rolled down
Reason analysis: the dough is strong
Solution: Increase the amount of water appropriately to make the dough dough moderately soft and hard.
6. Fault: The skin can not come out
Cause analysis: The dough is too soft or too sticky
Solution: knead the dough with flour until moderate hardness, or reduce the amount of water. And coat the finished dough pieces with dry flour on both sides.
7、Fault: The face has cracks
Cause analysis: put in oil or salt
Solution: Do not put any salt and oil when flour.
- We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
