• How To Replace A CV Axle Shaft?
  •  
  • Tools Required:
    • Drain Pan
    • Car Jack
    • Jack Stands
    • Wheel Chocks
    • Torque Wrench
    • Hammer or Mallet
    • Pry Bar or CV Axle Puller
    • Ratchet
    • Socket Set
    • Screwdrivers
    • Lug Wrench
    • Wrenches
     
  • Step 1: Removing The Old CV Axle
  •  

    • CV Axle Shaft Front Right for Toyota Prius 2016-2020 for Corolla 2020 1.8L

    How To Replace A CV Axle Shaft?

     

    Tools Required:

    • Drain Pan
    • Car Jack
    • Jack Stands
    • Wheel Chocks
    • Torque Wrench
    • Hammer or Mallet
    • Pry Bar or CV Axle Puller
    • Ratchet
    • Socket Set
    • Screwdrivers
    • Lug Wrench
    • Wrenches

     

    Step 1: Removing The Old CV Axle

     

    1. Park your car on a leveled surface, secure the vehicle’s wheel using wheel chocks, and engage the parking brakes.
    2. Take a lug wrench and loosen the wheel’s lug nuts. Do not remove the lug nuts completely.
    3. Place a jackunder the car to lift it off the ground and install the jack stand under the vehicle. You can also refer to the owner’s manual for the right placement of the jack.
    4. Remove wheels by loosening the lug nuts using a lug wrench. Remove the hubcap to access the axle nut and loosen it using a breaker bar.
    5. Remove the axle nut and the brake assembly using a wrench and socket. Remove the brake caliper. Detach the brake fluid hose and set it aside safely to keep it secure.
    6. Unbolt the castle nut on the outer tie rod and remove it from the steering knuckle using a tie rod end puller tool.
    7. Unbolt the hub from the strut by loosening the bolts that held them together. Once these bolts are removed, the hub should only be connected by the axle through the center hole.
    8. Remove the CV axle from the hub by hitting the CV joint with a drift chisel and a hammer. You can also use a screwdriver to pop the CV joint out and disconnect the CV shaft from the hub assembly.
    9. Before removing the CV shaft completely, place a drain pan underneath the engine where the other end of the CV shaft is connected to the transmission.
    10. Use a pry bar to remove the CV axle from the engine side. If the axle doesn’t come loose, try twisting it back and forcing it to break the seal.

     

    It’s normal for some transmission fluid to leak out as you remove the axle from the CV joint. Replace the CV shaft seal if you see any transmission fluid leaking. Use a seal puller tool to get it out, if it’s jammed.

     

    Step 2: Installing The New CV Axle

     

    1. Just as you removed the old CV axle, insert the new one into the same spot in the transmission housing. The peg will slide in until the axle is flush against the housing. Use a rubber mallet to gently tap it from the other side of the axle, to get it seated into place.
    2. Reinsert the other end of the axle shaft through the hub assembly in the same spot where you removed the old axle.
    3. Reattach the tie rod to the steering knuckle and rejoin the hub with the strut. Use a torque wrench to fasten the bolts to the recommended specifications.
    4. Reinstall the brake rotors and brake calipers. Make sure the brake line is not damaged in the process and working fine.
    5. Fasten the axle nut to the specifications mentioned in the manual using a torque wrench and replace the hub cap.
    6. Reattach the sway bar if removed earlier, and fasten the lug nuts to reattach the wheel.
    7. Refill the transmission fluid recommended for your vehicle.
    8. After the wheel is attached, you can lower the car by removing the jack and jack stands. Tighten the lug nuts and remove the wheel chocks to take the vehicle for a test drive.

     

    Tips While Replacing A CV Axle

     

    • If you are not experienced in carrying out vehicle maintenance and haven’t changed the suspension or related parts of your vehicle, we recommend you consult a professional. There are some vehicle repairs that should be done by qualified mechanics to prevent any further issues.
    • Use a torque wrench to tighten the nuts and bolts to the torque values specified by the manufacturer. You can also refer to the user manual for specific torque values. Never use a power tool to torque the spindle nut because you can damage the spindle nut and the outer CV joint.
    • A CV boot failure is a bad news for any CV joint because, if the boot fails, the CV joint will lose its lubrication and eventually fail. While installing the CV shaft, ensure the boots are secured properly and show no signs of visible damage like cracks and splits.
    • Before replacing the old CV axle shaft, check whether the new axle shaft has the same specifications or not. It should have the same compressed length, same inner and outer stub length and spline count for proper fitment, and inner and outer seal diameters. 
    • Check the transmission fluid for discoloration while replacing the CV axle shaft. It’s advised to replace your transmission fluid and seal if necessary.

     

    If your CV axles have a sensor ring around the outer joint, ‌handle the shaft with care during installation. Any damage to the sensor ring can cause the Anti Lock Braking (ABS) system to get damaged and malfunction.


    Item Specifics
    Brand :lujuntec
    Manufacturer Part Number :LJ182385T01
    Interchange Part Number :66-5449,4341047040
    Manufacturer Warranty :1 Year
    Superseded Part Number :665449
    Fitment Type :Direct Replacement
    Compatible Makes :Toyota
    Model :for Corolla, Prius, Prius AWD-e, Prius Prime
    Year :2016-2020
    Engine :L4 1.8L
    Placement on Vehicle :Front Right
    Input Shaft Spline Count :24
    Output Shaft Spline Count :26

    Payment

    We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    About Shipping

    1. Items will be shipped within 24 hours after getting your verified payment.

    2. US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping time

    About Return

    We stand behind every product we sell.

    All of our brand new items come with a 30-Day money-back or exchange guarantee.

    Fitment Notes

    Please consult with your mechanic, or contact us, if you are not sure of fitment for your vehicle. READ the notes on the compatibility chart.

    We are not responsible for incompatible items due to buyer's error, and a restocking fee as well as shipping charges will be deducted from returns or exchanges.

    Shop Category
     Store Home
     Brake Rotors & Pads
     Towing Mirrors
     Wheel Hub Bearing
     Timing Belt Kits
     Door Handle
     Wheel Spacers
     Water Pump
     Fuel Pumps
     Fuel Injector
     Suspension Kit
     Leveling lift kit
     Wheel Lug Nuts
     ABS Wheel Speed Sensor
     Knock Sensor
     Air Cleaner Filter Box
     Jack Stands
    Hot Item
    Delivery

    content_src_url

    New List Item
    Help & Info
    Payment Policy
    Shipping Policy
    Return Policy
    FAQ
    About Us
    CV Axle Shaft Front Right for Toyota Prius 2016-2020 for Corolla 2020 1.8L

    How To Replace A CV Axle Shaft?

     

    Tools Required:

    • Drain Pan
    • Car Jack
    • Jack Stands
    • Wheel Chocks
    • Torque Wrench
    • Hammer or Mallet
    • Pry Bar or CV Axle Puller
    • Ratchet
    • Socket Set
    • Screwdrivers
    • Lug Wrench
    • Wrenches

     

    Step 1: Removing The Old CV Axle

     

    1. Park your car on a leveled surface, secure the vehicle’s wheel using wheel chocks, and engage the parking brakes.
    2. Take a lug wrench and loosen the wheel’s lug nuts. Do not remove the lug nuts completely.
    3. Place a jackunder the car to lift it off the ground and install the jack stand under the vehicle. You can also refer to the owner’s manual for the right placement of the jack.
    4. Remove wheels by loosening the lug nuts using a lug wrench. Remove the hubcap to access the axle nut and loosen it using a breaker bar.
    5. Remove the axle nut and the brake assembly using a wrench and socket. Remove the brake caliper. Detach the brake fluid hose and set it aside safely to keep it secure.
    6. Unbolt the castle nut on the outer tie rod and remove it from the steering knuckle using a tie rod end puller tool.
    7. Unbolt the hub from the strut by loosening the bolts that held them together. Once these bolts are removed, the hub should only be connected by the axle through the center hole.
    8. Remove the CV axle from the hub by hitting the CV joint with a drift chisel and a hammer. You can also use a screwdriver to pop the CV joint out and disconnect the CV shaft from the hub assembly.
    9. Before removing the CV shaft completely, place a drain pan underneath the engine where the other end of the CV shaft is connected to the transmission.
    10. Use a pry bar to remove the CV axle from the engine side. If the axle doesn’t come loose, try twisting it back and forcing it to break the seal.

     

    It’s normal for some transmission fluid to leak out as you remove the axle from the CV joint. Replace the CV shaft seal if you see any transmission fluid leaking. Use a seal puller tool to get it out, if it’s jammed.

     

    Step 2: Installing The New CV Axle

     

    1. Just as you removed the old CV axle, insert the new one into the same spot in the transmission housing. The peg will slide in until the axle is flush against the housing. Use a rubber mallet to gently tap it from the other side of the axle, to get it seated into place.
    2. Reinsert the other end of the axle shaft through the hub assembly in the same spot where you removed the old axle.
    3. Reattach the tie rod to the steering knuckle and rejoin the hub with the strut. Use a torque wrench to fasten the bolts to the recommended specifications.
    4. Reinstall the brake rotors and brake calipers. Make sure the brake line is not damaged in the process and working fine.
    5. Fasten the axle nut to the specifications mentioned in the manual using a torque wrench and replace the hub cap.
    6. Reattach the sway bar if removed earlier, and fasten the lug nuts to reattach the wheel.
    7. Refill the transmission fluid recommended for your vehicle.
    8. After the wheel is attached, you can lower the car by removing the jack and jack stands. Tighten the lug nuts and remove the wheel chocks to take the vehicle for a test drive.

     

    Tips While Replacing A CV Axle

     

    • If you are not experienced in carrying out vehicle maintenance and haven’t changed the suspension or related parts of your vehicle, we recommend you consult a professional. There are some vehicle repairs that should be done by qualified mechanics to prevent any further issues.
    • Use a torque wrench to tighten the nuts and bolts to the torque values specified by the manufacturer. You can also refer to the user manual for specific torque values. Never use a power tool to torque the spindle nut because you can damage the spindle nut and the outer CV joint.
    • A CV boot failure is a bad news for any CV joint because, if the boot fails, the CV joint will lose its lubrication and eventually fail. While installing the CV shaft, ensure the boots are secured properly and show no signs of visible damage like cracks and splits.
    • Before replacing the old CV axle shaft, check whether the new axle shaft has the same specifications or not. It should have the same compressed length, same inner and outer stub length and spline count for proper fitment, and inner and outer seal diameters. 
    • Check the transmission fluid for discoloration while replacing the CV axle shaft. It’s advised to replace your transmission fluid and seal if necessary.

     

    If your CV axles have a sensor ring around the outer joint, ‌handle the shaft with care during installation. Any damage to the sensor ring can cause the Anti Lock Braking (ABS) system to get damaged and malfunction.

    Item Specifics
    Brand :lujuntec
    Manufacturer Part Number :LJ182385T01
    Interchange Part Number :66-5449,4341047040
    Manufacturer Warranty :1 Year
    Superseded Part Number :665449
    Fitment Type :Direct Replacement
    Compatible Makes :Toyota
    Model :for Corolla, Prius, Prius AWD-e, Prius Prime
    Year :2016-2020
    Engine :L4 1.8L
    Placement on Vehicle :Front Right
    Input Shaft Spline Count :24
    Output Shaft Spline Count :26


    We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    1. Items will be shipped within 24 hours after getting your verified payment.

    2. US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping time

    We stand behind every product we sell.

    All of our brand new items come with a 30-Day money-back or exchange guarantee.

    Please consult with your mechanic, or contact us, if you are not sure of fitment for your vehicle. READ the notes on the compatibility chart.

    We are not responsible for incompatible items due to buyer's error, and a restocking fee as well as shipping charges will be deducted from returns or exchanges.


    All right reserved.