• Vehicle Information:
  •  
  • 2013-2018 Ford C-Max L4 2.0L(without Housing) 2017-2019 Ford Escape L4 2.5L(without Housing) 2016-2018 Ford F-650 V10 6.8L(without Housing, GAS) 2016-2018 Ford F-750 V10 6.8L(without Housing, GAS) 2012-2018 Ford Focus L4 2.0L(without Housing, Naturally Aspirated) 2013-2019 Ford Fusion L4 2.0L(without Housing, Naturally Aspirated) 2016-2019 Ford Transit Connect L4 2.5L(without Housing) 2013-2019 Lincoln MKZ L4 2.0L(without Housing, FULL HYBRID EV-GAS (FHEV))
  • Kit Includes:
  •  
  •  
  •  
  • 1x Mass Air Flow Sensor/Meter
  •  
  •  
  •  

    • For 2013-2019 Ford Fusion L4 2.0L mass Air Flow Sensor Meter MAF

    Vehicle Information:

     

    2013-2018 Ford C-Max L4 2.0L(without Housing)
    2017-2019 Ford Escape L4 2.5L(without Housing)
    2016-2018 Ford F-650 V10 6.8L(without Housing, GAS)
    2016-2018 Ford F-750 V10 6.8L(without Housing, GAS)
    2012-2018 Ford Focus L4 2.0L(without Housing, Naturally Aspirated)
    2013-2019 Ford Fusion L4 2.0L(without Housing, Naturally Aspirated)
    2016-2019 Ford Transit Connect L4 2.5L(without Housing)
    2013-2019 Lincoln MKZ L4 2.0L(without Housing, FULL HYBRID EV-GAS (FHEV))

    Kit Includes:

     

     

     

    1x Mass Air Flow Sensor/Meter

     

     

     

    Note: To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table. Also review the notes section in the compatibility chart for additional specifications about this part.

     

     

    Specification:


    *The Mass Air Flow (MAF) sensor measures the amount of air flow entering the intake manifold using a heated grid or wire.

    *The PCM uses this signal primarily for fuel control.

    *The Mass Air Flow sensor is located in the intake ducting after the air filter.

     

    INSTALLING:the replacement MASS AIR FLOW SENSOR(MAF):
    *. Position MAF sensor in the vehicle. Make sure the airflow direction indicated on the sensor is toward the engine.
    *. Install sensor to air duct seal(s), if so equipped, on the replacement MAF sensor.
    *. Connect the MAF sensor to the throttle body air cleaner ducts. If the sensor mounts directly on the throttle body, install and tighten the mounting screws to 10 ft-lb. DO NOT OVERTIGHTEN!
    *. Position clamps over the air duct/MAF sensor connections and tighten. Replace the clamps if necessary. (NOTE: For the MAF sensor to work properly, the sensor/air duct connections must be airtight.)
    *. CAREFULLY plug the harness connector lead into the MAF sensor.

     

     


    Item Specifics
    Brand CLASSIC AutoParts
    Manufacturer Part Number C11372601APS
    Type Mass Airflow Sensor (MAF Sensor)
    Air & Fuel Sensor Type MASS AIR FLOW Sensor/Meter
    Manufacturer Warranty 10 Years
    Interchange Part Number AF10374A
    Fitment Type Direct Replacement
    Placement on Vehicle Front
    Housing w/ housing

    Payment
    1. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    2.if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
    Shipping
    1.All the orders are shipped from USA warehouse.
     
    2.Orders processed within 24 hours of payment verification.
     
    3. The images shown are not the actual item and are for your reference only.
     
    4.If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
    Returns

    We stand behind every product we sell.

    All of our brand new items come with a 30-Day money-back or exchange guarantee.

    Contact Us

    If there is an issue with shipping or the item you purchased please contact us via ebay message or call us before opening a case or leaving feedback.We will try our best to resolve any kind of issue.

    Feedback

      We maintain high standards of excellence and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us feedback, so that we can satisfactorily address your concerns.

    Store Category
     Store Home
     Horns
     Dipstick
     Lift Support
     Air suspensions
     snorkel air intake
     complete struts
     Cylinder Piston Kit
     Strut Mount
     coilover
     Shocks & Struts
     Motorcycle Exhaust Pipe
     Power Brake Booster
     Bumper
     Engine Splash Shield
     Strut+Suspension+Bearing
     Brake caliper
     Brake system
     Fuel System
     Lawn Mower Clutch & Assemblie
     A/C Compressor and Accessories
     Car Sun Visor
     Golf Part Cart and Seat Covers
     Outdoor Power Pressure Washers
     Car Mirror Assemblies
     Timing Chain Kit
     Engine Head Gasket Sets
     Timing Belt Kit
     Car Roof Rack
     Truck Bed Cover
     Camper Sun Shade
    Hot Item
    Fast and Free

    content_src_url

    Best seller

    content_src_url
    For 2013-2019 Ford Fusion L4 2.0L mass Air Flow Sensor Meter MAF

    Vehicle Information:

     

    2013-2018 Ford C-Max L4 2.0L(without Housing)
    2017-2019 Ford Escape L4 2.5L(without Housing)
    2016-2018 Ford F-650 V10 6.8L(without Housing, GAS)
    2016-2018 Ford F-750 V10 6.8L(without Housing, GAS)
    2012-2018 Ford Focus L4 2.0L(without Housing, Naturally Aspirated)
    2013-2019 Ford Fusion L4 2.0L(without Housing, Naturally Aspirated)
    2016-2019 Ford Transit Connect L4 2.5L(without Housing)
    2013-2019 Lincoln MKZ L4 2.0L(without Housing, FULL HYBRID EV-GAS (FHEV))

    Kit Includes:

     

     

     

    1x Mass Air Flow Sensor/Meter

     

     

     

    Note: To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table. Also review the notes section in the compatibility chart for additional specifications about this part.

     

     

    Specification:


    *The Mass Air Flow (MAF) sensor measures the amount of air flow entering the intake manifold using a heated grid or wire.

    *The PCM uses this signal primarily for fuel control.

    *The Mass Air Flow sensor is located in the intake ducting after the air filter.

     

    INSTALLING:the replacement MASS AIR FLOW SENSOR(MAF):
    *. Position MAF sensor in the vehicle. Make sure the airflow direction indicated on the sensor is toward the engine.
    *. Install sensor to air duct seal(s), if so equipped, on the replacement MAF sensor.
    *. Connect the MAF sensor to the throttle body air cleaner ducts. If the sensor mounts directly on the throttle body, install and tighten the mounting screws to 10 ft-lb. DO NOT OVERTIGHTEN!
    *. Position clamps over the air duct/MAF sensor connections and tighten. Replace the clamps if necessary. (NOTE: For the MAF sensor to work properly, the sensor/air duct connections must be airtight.)
    *. CAREFULLY plug the harness connector lead into the MAF sensor.

     

     



    1. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    2.if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
    1.All the orders are shipped from USA warehouse.
     
    2.Orders processed within 24 hours of payment verification.
     
    3. The images shown are not the actual item and are for your reference only.
     
    4.If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    We stand behind every product we sell.

    All of our brand new items come with a 30-Day money-back or exchange guarantee.

    If there is an issue with shipping or the item you purchased please contact us via ebay message or call us before opening a case or leaving feedback.We will try our best to resolve any kind of issue.

      We maintain high standards of excellence and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us feedback, so that we can satisfactorily address your concerns.


    All rights reserved.