Beschreibung der Dezimalzeiten:

Erläuterung der Dezimalstelle und der Zeiteinheiten, die sie darstellt:

(X.XX) Dezimalpunkt zur hundertsten Stelle, Zeitbereich 0.01~9.99 Sekunden

(XX.X) Dezimalpunkt zur zehnten Stelle, Zeitbereich 0.1~99.9 Sekunden

(XXX) hat keinen Dezimalpunkt, Zeitbereich 1-999 Sekunden

(XXX.) Dezimalpunkt an einem Ort, Zeitbereich 1-999 Minuten

(XX.X.) Die Dezimalstelle ist sowohl an einer als auch an zehn Stellen, und die Zeit liegt zwischen 10 Minuten und 9990 Minuten

Display ausschalten: Wenn sich der eingestellte Zustand nicht befindet, drücken Sie die K4-Taste, um den Bildschirm auszuschalten, und drücken Sie dann erneut, um ihn wieder einzuschalten

Es ist notwendig, hier auf den Status der Dezimalstelle zu achten, da viele Kunden sie falsch eingestellt haben

Operating modes (32 types - 1-way/2-way independent use)

P-11: Tap mode, with signal suction, without signal disconnection.
P-12: Self-locking mode, relay state flips once after each trigger.
P-13: After triggering, the relay will be engaged and disconnected after A time delay; the trigger is invalid during the delay period.
P-14: After triggering, the relay is activated and disconnected after delay A time; the trigger is re-timed during the delay period.
P-15: After triggering, the relay is activated and disconnected after delay A time; the trigger is cumulative timed during the delay period.
P-16: After triggering, the relay is activated and disconnected after time delay A; reset is triggered during the delay period (relay disconnected).
P-17: After triggering, the relay is engaged during the signal duration, the input signal disappears, and is disconnected after delay A time; the relay is triggered again during the delay period to remain engaged and the timing stops until the last signal disappears, and is disconnected after delay A time.
P-18: Immediately after energisation, the relay is activated and disconnected after a delay of A seconds; until the next energisation.

P-21: Give signal, after A time delay the relay is activated.
P-22: Give a continuous signal, after A time exceeded, the relay is engaged; the signal disappears, the relay is disconnected.
P-23: Signal disappears beyond A time, relay is engaged; with signal, relay is disconnected.
P-24: Give continuous signal, after exceeding A time, relay is absorbed; signal disappears more than A time, relay is disconnected.
P-25: Give continuous signal, after exceeding A time, relay is engaged; give continuous signal again, after exceeding A time, relay is disconnected.
P-26: Give signal, relay is activated for A time and then disconnected; after the signal disappears relay is activated again for A seconds and then stops.
P-27: With pulse signal (rising edge or falling edge) relay breaks; without pulse signal, relay delays A time and then absorbs (continuous high level or continuous low level is considered as no pulse).
P-28: After power on, relay is absorbed after delay A time until power off. (Signal line IN+ IN- may not be connected).
P-31: After power-on, relay is engaged for A time, disconnected for B time, infinite cycle; power-off stop.

P-32: With a continuous signal, the relay is engaged for A time, disconnected for B time, infinite loop; the signal disappears and the loop is terminated.
P-33: Give a signal once, the relay absorbs A time, disconnect B time, infinite loop; give a signal again, terminate the loop.
P-34: After power on, after delay time A, the relay will be engaged, and after engagement time B, it will be disconnected.
P-35: Give a signal once, after delay A time, the relay will be engaged and disconnected after engagement B time.
P-36: Give continuous signal, after exceeding A time, the relay will absorb, and disconnect after absorbing B time; the signal disappears, the timing is cleared to zero, and the relay disconnects.
P-37: With signal, the relay is automatically disconnected after A time, and then timed for B time after disconnection; the signal trigger is invalid during A+B time.
P-38: With signal, the relay is automatically disconnected after the A time of absorption, after disconnection and then timing B time, and again after the A time of absorption.
P-41: No action when signal is present; signal disappears and trigger is triggered; relay is disconnected after A time delay.
P-42: Signal disappears, relay absorbs after time delay A; relay disconnects after time delay B again.

P-43: Signal disappear, disappear beyond A time after the relay absorb; then delay B time after the relay disconnect.
P-44: after power on, relay absorb A time, disconnect B time; cycle C times after relay disconnect stop, (signal line IN + IN - can not be connected)
P-45: After power-on, no action; after giving signal, the relay will be engaged for A time and disconnected for B time; after cycling C times, the relay will be disconnected and stopped; if a signal is given, it will be executed again.
P-46: After giving signal more than A time, the relay is absorbed; keep absorbed; disconnect and stop.
P-47: After giving a signal more than A times, the relay is absorbed; it is disconnected after B time of absorption.
P-48: After giving the signal more than A times continuously in C time, the relay will absorb B time and then disconnect to stop.