To see all the different Kits I sell, Click On "SEE sellers OTHER ITEMS" To The Right Under " Sellers Imformation",


    THE ORIGINAL SHIM KIT NOT A WEAK CHINA KNOCK OFF with wrong tools

     To see all the different Kits I sell, click on "SEE OTHER ITEMS" to the right under "Seller information".

     This kit will make your truck start faster cold and run with more power and EXTEND the life of your injectors up to 200K miles more; by renewing the armature plate clearance to .004" to,005". like new injectors. WITHOUT REMOVING YOUR INJECTORS. Over 3000 kits sold.                                                                                                                                                            

    FROM INSTRUCTIONS                                                                                                                       

    If You have a tight .002” or less then add a .004” Armature Shim and then add a .005” Solenoid shim. (.002” & .003”).                                                                                                                                                                                                

    If you have a loose .002” or above add a .002” Armature Shim and .003” Solenoid Shim. 

     If your truck has been RUNING GREAT warm but, has STARTED  MISSING  OR  is HARD TO START: You may not need to rebuild your injectors .  You may only need to install THIS Shim Kit, because you may have  LOW ARMATURE  TO ADAPTER HOUSING  CLEARANCE causing a stiction affect.  THIS IS THE  BIGGEST PROBLEMS CAUSING INJECTORS TO STOP WORKING!!! 

    My Kits are made in the USA  with 20 years of experience Shimming and Working on my fleet of Power Strokes and shipped in the USA ( Other Sellers' are China Knock-offs of my shim kit with hard to read photocopies of  my instructions and are from China (They do not pay US Taxes) without .002"armature shims and the wrong tools to install shims and weaker China Screws.  Theirs are shipped to the USA  with Smart Post  E-Commerce Shipping from China) 

     This kit will make your truck start faster cold and run with more power and EXTEND the life of your injectors up to 200K miles more  by renewing the armature plate clearance to over .004". like new injectors. WITHOUT REMOVING YOUR INJECTORS. Over 2000 kits sold

      Shims only make your injectors last longer. So, the more you put under the armature the longer they will last. New they are over .004" But, you must put the same amount of shims (plus .001" for poppet valve up-stop wear) under the solenoids to keep the armature from hitting the solenoids.
      The important clearance is between the solenoid and the armature when the solenoid is energized.      The clearance Must be keep close to .003" plus or minus .001" to work right: which is hard to measure without energizing the solenoid. When new they were .004 - .005". 

      Kit Works  on most HEUI injectors; 1994 - 2003 Ford 7.3L PowerStroke,    International T444E / DT466e / 1530E . Also works on Cat 3126B top solenoid , International Perkins  4.5L, 6.0L, & 1300edi   HEUI injectors. 

      Will do up to TEN (10)  INJECTORS, can add   to 200k miles to your old  injectors WITHOUT REMOVING THEM  and can also be done when injectors are removed for O-ring replacement or repair.   Makes you injectors last up to 200k longer  ( NO NEED TO BUY NEW INJECTORS)    

      

    Easy step by step instructions for the do it yourself person  to install.

     Also Instruction to remove valve covers, pull injectors for O-ring replacement and reinstall .

    No need to buy new injectors. Or remove injectors to install.

    IT WILL NOT FIX INJECTORS WITH BAD SOLENOID OR OTHER MECHANICAL PROBLEMS !! 

    If you need the SPECIAL TOOLS to install, see my OTHER  LISTING.    eBay item number:201596495902

      KIT  COMES WITH: 

    1. Packets of TEN  .004" and TEN .002" thick stainless steel ARMATURE washers.  ( TO BE INSTALLED UNDER THE ARMATURE PLATE TO INCREASE THE  CLEARANCE  to over .004"

      2.  FORTY   .002" and FORTY .003" stainless steel  SOLENOID SPACER SHIMS. One of each placed under all four corners of the coil (for a total .005") to increase the SOLENOID to armature clearance, when SOLENOID is energize. 

    3. TEN ( 10 )  DIPACO  Part #DPS0010  HARDENED SCREWS (Made in Italy for OEM Injectors) with T10 Torx heads to UPDATE your old weaker OEM security stock screws. 

      4. A  SPECIAL EZ OUT  tool with instructions TO REMOVE AND REUSE ANY STRIPED OUT SOLENOID SCREWS when someone used  THE WRONG TORX.                                                                                                                                        

    5.  STEP BY STEP  INSTRUCTIONS WITH COLOR PICTURES to install the .004" and .002" armature shims and  INSTALL the .002" and .003"  SOLENOID SPACER SHIMS (total .005") and tips on thing to check with the valve cover off.                        

    6.  STEP BY STEP  INSTRUCTIONS to remove valve covers to install the shims 

    I  am a 76-year-old mechanic that works on a fleet of 6.9 and 7.3 Power Strokes for the last 25 years and want to help the do-it-yourselfer keep their trucks running. By sharing the knowledge I have learned over 50 years of experience. My instruction is written from my experience of working on trucks and adding shims to many trucks