Black Seat made in USA

Fits all 

4200 4300 4400 4500 4600 4700 

John Deere tractors

 

over $ 200.00 at most dealers

This seat has lumbar support

slide tracks not included...

armrests and slide tracks optional



Mounting 11.25 wide by 11.5 inches

This seat will replace LVA10029 

 OK LOOK AT THIS SEAT.... WE GET NOTHING BUT COMPLIMENTS ON THIS SEAT. THE LUMBAR SUPPORT OF YOUR BACK IS THE KEY POINT....

THERE IS NO SEAT AT THIS PRICE THAT FORMS TO YOUR BACK.... ITS NOT JUST A STRAIGHT BACK YOU LEAN ON.... GO AHEAD LOOK AT THE PICTURES AGAIN YOU WILL SEE....  WE HAVE CHEAPER AND MORE EXPENSIVE SEATS BUT WE BRAG ABOUT THIS ONE .........READ ON THERES MORE,....

Flat Rate SHIPPING TO THE 48 STATES. WE WILL SHIP UPS 

See common questions at bottom.

 

NEWS FLASH !!  Bobcat Dealers are buying this along with our ULTRA LOW SUSPENSION can be found in our listings and reccommending them for more comfort and smoother ride !! .............................VISIT OUR STORE TO SEE.

YOU ARE LOOKING AT THE NEW SPRAY SKIN TECHNOLOGY (SST) BUCKET SEAT.

 Can fit many mowers and other equipment  

Exmark – GEHL –  Kubota – POLARIS – SCATTRAK – Scag – THOMAS – TORO - TOYOTA – VOLVO - YALE - CLARK 

MOUNTING... THE SEAT HAS AN 11.25" SIDE TO SIDE X 11" FRONT TO BACK MOUNTING AND 4" MOVEMENT SINGLE LOCKING SLIDE TRACKS.

OVERALL WIDTH IS 18.50 AND OVERALL HIGHT IS 20.25. THERE IS A DRAIN HOLE IN THE SEAT FOR WATER TO RUN OUT.  THIS SEAT HAS MANY BENEFITS. BETTER THAN VINYL OR RUBBER. MANY OTHER SEATS AND SUSPENSIONS ARE ALSO AVAILABLE, JUST ASK.  

  • COMFORTABLE WITH FIXED LUMBAR SUPPORT 
  • Mounting 11.25" wide by 11" front to back *NOTE WITH 2.75 INCH SUSPENSION, MOUNTING CAN BE 9.5 WIDE BY 11 OR 10.65-11.25 (SLOTTED) BY 11 FOR A SMOOTHER RIDE ON YOUR EQUIPMENT
  • MADE FROM SPRAY SKIN TECHNOLOGY (SST) URETHANE FOAM
  • NO SEWN COVERS
  • DURABLE: SST STRETCHES UP TO 500% COMPARED TO EITHER VINYL OR FOAM-IN-PLACE, WHICH STRETCHED 100-110%
  • WILL NOT CRACK OR PEEL AWAY FROM FOAM
  • VISUALLY APPEALING
  • COMFORTABLE WITH FIXED  LUMBAR SUPPORT 
  • WATERPROOF
  • COST EFFECTIVE
  • OPTIONS AVAILABLE  PRESSURE SEAT SWITCH, SUSPENSIONS FROM 2.75 INCH TO 9 INCH IN HEIGHT AVAILABLE AIR OR MECHANICAL. SWIVEL

*Common Questions. Does it fit my_____?

As we get this question so many times, to answer most of them we need to know the bolt pattern of your seat. The bolt pattern for this seat is 11.25 INCHES WIDE BY 11 INCHES FRONT TO BACK.


** THE FLAT RATE SHIPPING COST FOR 48 STATES ONLY **for Alaska and Hawiii AND ALL OTHER COUNTRIES ASK FOR FREIGHT QUOTE BEFORE BUYING  MAY NOT BE ABLE TO SHIP TO SOME COUNTRIES. 

Note: we will make every effort to remember to send nuts for installation. Regardless use 5/16 nuts. the nuts holding your original seat are metric and will go on hard and wreck thread

Important installation note:

As John Deere has changed part numbers some seats are held on by metric bolts or nuts (M8 OR .315) AND SOME USE 5/16 (.325) BOLTS OR NUTS.

THIS SEAT WE SELL USES 5/16 NUTS.  WE HAVE THESE SEATS SHIP DIRECT TO YOU FROM THE CLOSEST WAREHOUSE AND AT THIS POINT THEY DON'T SUPPLY NUTS OR BOLTS.

WHEN INSTALLING BE SURE TO USE 5/16 BOLTS OR NUTS WHEN INSTALLING OR YOU WILL CAUSE THE THREADED INSERT TO SPIN. THANKS 



You will receive two packages.

One package with the seat and another package with brackets.