Product Information
- Neptune Hex Nyloc nuts are a High Tensile A4-80 Stainless Steel nut with the same class properites and strength as high tensile carbon steel class 8.8 nuts. They are used to accommodate the higher tensile loads in a Neptune assembly
- The nylon material in a Nyloc nut prevents loosening from vibration and cross threads to stop the nut from backing off of the fastener. The insert deforms elastically over the threads of the screw, but threads are not cut into the nylon. The nylon insert locks the nut in two ways. First, it forces the bottom face of the screw threads against the top face of the nut threads, increasing the friction between the two. Second, the nylon applies a compressive force against the screw itself. They can also be used to assist sealing the bolt thread against seepage of oil, water, petrol, paraffin and other liquids.They come in a variety of materials
- Features / Benefits:
- Products have full traceability
- Ultimate Corrosion resistance
- High Strength
- Higher yield strength and tighter tolerances
- Fatigue resistance
- Very low magnetic permability
- Material / Coating: High tensile class 8.8 marine grade stainless steel A4-80 G316 is the ultimate corrosion resistance and high strength fastener
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Galling: Can occur when excessive pressure is used to tighten a nut onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the nut more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Thread Pitch (Metric): Is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Differences may exist between batches such as inside dimension, outside diameter, thickness, visible stamped markings, appearance and actual finish
- Photos: Represent the product, not the size. Our title has industry sizing but if additional information is required refer to the CAD drawing, Specifications Table or Technical Specifications PDF
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- PDF data sheet: PDF data sheets are provided as a reference guide only. Specifications may change without notice
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and The Fastener Warehouse is not responsible for any loss, claim or damages arising therefrom. In developing this information, The Fastener Warehouse has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
Technical Specification
Nyloc Insert Nut
Type
M4 (4mm)
Thread Size
0.70mm
Thread Pitch
M4 x 0.70p Coarse
Size x Pitch
Metric - Coarse
Thread Type
Right Hand
Thread Direction
Metric
System of Measurement
5/32"
Closest Size in Imperial
7mm
Spanner Size
6.78 - 7.00mm
Across Flats Af
7.66 - 8.08mm
Across Corners Ac
3.20mm
Hex Height H
4.70 - 5.00mm
Overall Nut Height B
High Tensile Stainless Steel
Material
High Tensile A4-80 G316
Grade
Ultimate
Corrosion Protection Level
DIN 985
Standard
Hobson Engineering
Brand
Brighton Best | Inox World
Alternative Brands
NN16NCM04
MPN
9350629150701
UPC
To reduce friction and galling,
Product Note (a)
Apply a lubricant to the male thread and assemble slowly
Product Note (b)
Free Shipping
Delivery
Select From The Dropdown Above
Number in Pack




