Features:

Condition: 100% Brand New

Color: Black

Light Color: Red/Blue/Green

1-6 Gear display

Installation:

Locate the Speed Sensor connector.

Ducati: The Speed Sensor is mounted at the rear wheel. Trace the cable from the sensor until you find the 3-pole black speed sensor connector. The connector is usually accessible by removing the right side fairing and on most models it is in close proximity of the right side engine cover.

MV Agusta: the connector is at the front sprocket cover. If in doubt, check the bike’s Service Manual or ask your dealer for the location of the Speed Sensor connector.

Confirmation:

1.    Separate the Speed Sensor connector (you might need to use a small flathead screwdriver to get the connector apart). Rotate the rear wheel while ignition is on. The speedometer should indicate 0. If so, turn the ignition off and proceed to the next step. Otherwise, if the speedometer registers a speed other than 0, you have not disconnected the correct coupler and need to look again.

2.    After separating the Speed Sensor connector, plug in both the male and female 3-pole GFYSHIP harness connectors. Make sure the connectors are fully seated.

3.    Find RPM/Timing Sensor (Pickup) connector. The sensor is mounted either on top, or the side of the crankcase. Trace the cable from the sensor until you find the 3-pole connector.

Here is the connector location on some popular models:

Monster S2R, Multistrada: At the left side, above horizontal cylinder, ziptied to frame.

Monster S4RS: Behind left side cover under seat.

ST3: At the right side of engine, zip-tied to frame.

If in doubt, check the bike’s Service Manual or ask your dealer for the location of the RPM/Timing Sensor connector.

4.    Disconnect the connector, and pull back the LARGER rubber boot from the plug, to leave the three wires exposed.

5.    Route the GFYSHIP Black/Green wire through the rubber boot from the back. Make sure the wire will NOT touch the exhaust pipe or cylinder block.

6.    Connect the GFYSHIP Black/Green wire to the wire in connector slot position 1, using the Red wire tap connector supplied.

Usage: Place the unstripped run wire (slot position 1) inside the run channel. Close the side cover until latched. Cut off the excess length, then insert the unstripped tap wire (Black/Green) completely and check its position. Insert the blade (u-contact) and press down by finger pressure. Then, fully depress the u-contact with pliers. Close the hinged top cover until latched.

Fitment:

For Suzuki Boulevard C50      2005-2008

For Suzuki Boulevard M50      2005-2020

For Suzuki Boulevard C90      2005-2012

For Suzuki Boulevard M90      2009-2020

For Suzuki Boulevard C109R/T      2008-2015  

For Suzuki Boulevard M109R/R2      2006-2010

For Suzuki DL650 V-Strom      2004-2011

For Suzuki DL1000 V-Strom      2004-2013 

For Suzuki GSF650 Bandit      2007-2008

For Suzuki GSF1250 N/NA Bandit      2007-2009

For Suzuki GSF1250 S/SA Bandit      2007-2016

For Suzuki GSX1400      2004-2009

For Suzuki GSXR600      2004-2005

For Suzuki GSXR750      2004-2005

For Suzuki GSXR1000   2003-2004  For Suzuki Intruder C800      2005-2008

For Suzuki Intruder M800      2005-2015

For Suzuki Intruder C1500      2005-2012

For Suzuki Intruder M1500      2009-2015

For Suzuki Intruder C1800R      2008-2015

For Suzuki Intruder M1800R      2006-2010

For Suzuki RMX-450Z      ALL YEARS  

For Suzuki RM-Z250 FI Model      ALL YEARS

For Suzuki RM-Z450 FI Model      2008-2020 

For Suzuki SV650      2003-2014

For Suzuki SV1000      2003-2009

For Suzuki VL800 Intruder Volusia      2005-2008

For Suzuki VL1500 Intruder      2005-2012

For Suzuki VLR1800      2008-2015  

For Suzuki VZ800 Marauder      2005-2015

For Suzuki VZ1500      2009-2015

For Suzuki VZR1800      2006-2010