• High Quality: The handle is made of heat-resistant plastic to prevent burns, and the nozzle is made of high-temperature and corrosion-resistant stainless steel. This plastic welding gun set is sturdy, compact and lightweight. 
• High Performance: The 1600W welder tool creates 230L/min jet of hot air that softens the plastic filler rod and the parts to be connected. The Temperature can be set to different melting points to meet different needs, so a variety of plastic materials can be used.
• Temperature Controllable: Equipped with a temperature controllable switch, the temperature can be adjustable from 30°C to 680°C, easy to operate. Both temperature and power can be adjusted to different melting points, which you can use on different plastic materials.
• Low Noise: The welder tool has low welding noise and vibration, guarantees comfortable work, high quality, special welding method, does not touch the welding joint, avoids moving parts and thermal shock.
• Safe & Sturdy: Applicable voltage 120V/60hz, safe and scientific power connection design to ensure no accidents during operation. Equipped with thermal protection tube and electronic heating protection system, more sturdy and reliable.
• Wide Application: This welder toll set can be wildly used for repairing plastic items such as truck curtains, tarpaulins, pool linings/membranes, water tanks, kayaks, vinyl flooring, car bumpers, etc. This is a must-have tool for every panel beater.

• Color: Blue
• Voltage: 120V/ 60Hz  
• Current: 13A
• Heating Power: 1600W
• Temperature: 30-680°C
• Noise: ≤65db
• Air Volume: 13.8m3/h
• Air Pressure: 2600pa
• Air Flow Rate: 230L/min (maximum)
• Insulating Intensity: 3750V
• Welding Gun Size: 13.19x3.54in/33.5x9cm
• Handle Diameter: 2.2in/5.6cm
• Wiring: 114.17in/2.9m

Welding gun+7 Accessories

• 1x pressing wheel
• 1 x heating core
• 1 x standard nozzle
• 1 x 20mm flat slit nozzle
• 1x 5.2mm round nozzle
• 1x 8mm Triangle welding nozzle
• 1x PVC plastic rods set

• 1.When using for the first time, there may be fire or smoke, which is a normal phenomenon, and it will disappear after a few minutes of power-on. 
• 2.After using the plastic welding gun, please adjust the temperature to a low level, and then shut down the gun after cooling down, so as to avoid residual heat damage to the parts and affect the service life.
• 3.Be careful not to use it near flammable gas, paper or other flammable materials during high temperature operation. The welding torch nozzle and hot gas are very hot and can burn the human body. Do not touch or spray hot air directly on the skin.
• 4.When the plastic sheet is heated to 130-150 degrees, it becomes a soft state, and it can be formed with a little pressure. The welding temperature is generally about 240 degrees. When welding, you should pay attention to the distance between the edge and the welding point to obtain the ideal welding position.
• 5.After the heating wire is broken, you can unscrew the connecting screw of the gun, take out the heating core, and replace it with the heating core of the same specification.
• 6.Pay attention to adjusting the operating temperature when soldering electronic components. The temperature of the air gun is as high as 600-650°C. For tin removal, different nozzles can be selected according to requirements. The nozzle and heating element are common with international brands, and are suitable for desoldering of most surface-mounted parts).
• 7.The hot air wall material welding gun should be handled gently after use, so as not to break the refractory porcelain material of the gun core and short-circuit the heating wire. 
• 8.Be sure to turn off the heat gun first when people are away.