Custom LED Blaster-X Integrated LED Tail Light — Yamaha YZF-R3 (2015–2024)
Programmable · Ultra-Bright · MPN 15FZ07_REV1A_PI2⚡ The Brightest Tail Light in Production
Dramatically brighter than your OEM tail light.64 ultra-bright LEDs — 32 red for the run/brake light and 32 amber for the integrated signals — are driven by our exclusive Blaster-X PWM electronics, which safely squeeze the maximum possible output from every LED. The result is, quite simply, the best and brightest production motorcycle tail light money can buy: you're seen sooner, and your braking and turns read instantly to traffic behind you.
Overview
The Blaster-X Integrated LED Tail Light for the 2015-2024 Yamaha YZF-R3 is a complete, plug-and-play replacement for your factory tail light — designed, built, and assembled by Custom LED in the USA. It drops into the stock location using the OEM connectors for both the tail light and the turn signals, so there's no cutting, splicing, or bodywork to modify.
This clear-lens version packs 32 ultra-bright red LEDs for the running and brake lights plus 32 ultra-bright amber LEDs for the fully integrated turn signals — all on stealth black boards for a clean, blacked-out look. Custom LED has pioneered integrated LED tail lights since 2003, and our Blaster-X units are widely regarded as the brightest and most effective integrated tail lights available, far outshining the OEM light they replace.
Key Features
- Brightest integrated tail light in production — far brighter than the OEM unit it replaces
- 64 ultra-bright LEDs — 32 red (run/brake) + 32 amber (integrated turn signals)
- Plug-and-play with the OEM tail light and turn-signal connectors — no cutting or splicing
- Direct OEM fitment; high-quality clear lens
- Fully programmable Blaster-X safety features — Brake Alert, Turn Alert & Strobe Mode (see below)
- Microprocessor-controlled (4 MHz), fully regulated design for precise, consistent output
- Built-in load equalizers & Sure-Blink relay compatibility
- Stealth black boards for an inconspicuous look
- Manufacturer-direct, backed by a 2-year warranty & satisfaction guarantee
Programmable Safety Features
Built in, ready to ride — and fully customizable. Every safety feature below is built right into the tail light and works the moment you install it. When you want to change the defaults, Custom LED's 2nd-Generation Programming Interface lets you do it yourself — enable or disable the startup sequence, choose your Brake Alert pattern, fine-tune the running and brake brightness, run a Demo Mode, or reset to factory defaults.
Programming is done simply by grounding the strobe-mode wire — no computer or special programmer required. The easiest way to do it is with the Blaster-X Control Switch (see Recommended Accessories below), and full step-by-step instructions ship with every unit.
Our proprietary pulse-width-modulation technology safely drives the LEDs to their maximum possible output — the engine behind what makes these the brightest tail lights in production.
The instant you touch the brakes, the brake light fires an attention-grabbing flash pattern before going solid — alerting drivers behind you and potentially buying back valuable reaction time. Choose from 11 selectable patterns, or disable it for standard brake operation.
On the side you're signaling, the light cycles between full-intensity amber and off for true high-contrast turn visibility — not just a color change. The red running light resumes once the signal cancels, and if you're braking while turning, the brake light takes priority between blinks.
Triggers an intense, high-frequency strobe across the tail light that's impossible to ignore — ideal as a hazard / emergency attention-getter. Engaged on demand through the control wire (pairs perfectly with the Blaster-X Control Switch below).
Blinks in perfect lock-step with your bike's flasher relay — compatible with OEM, aftermarket, and programmable relays — and if it ever misses a blink command, it automatically blinks that side so your signal never just sits on.
Custom LED turn signals are intentionally non-sequential — non-sequential signals have been shown to be more conspicuous and effective on motorcycles.
Specifications
| Fits | 2015-2024 Yamaha YZF-R3 |
|---|---|
| LEDs | 64 total — 32 ultra-bright red (run/brake) + 32 ultra-bright amber (turn signals) |
| Lens | Clear (a Smoked-lens version is also available — see the selector near the top) |
| Control | 4 MHz microprocessor-controlled, fully regulated — with Blaster-X PWM |
| Programmable | Brake Alert (11 patterns), Turn Alert, Strobe Mode, adjustable brightness |
| Connectors | OEM plug-and-play (tail light + turn signals) |
| Made in | USA |
| Warranty | 2-Year Warranty + Satisfaction Guarantee |
Compatibility
Yamaha YZF-R3 — 2015-2024
Direct OEM replacement for the 2015-2024 Yamaha YZF-R3. If you're unsure, compare your stock tail light connector or message us before ordering.
Recommended Accessories
Common companions for this tail light (sold separately):
Blaster-X Control SwitchA panel-mount On-Off-Momentary switch that controls Strobe Mode and the Blaster-X programming features — prewired and plug-and-play.View on eBay →
ELFR-1 Electronic LED Flasher Relay with OEM ConnectorPlug-and-play LED flasher relay that keeps your turn signals blinking at the correct OEM rate after going LED, with near-zero turn-on delay.View on eBay →
H7 LED Headlight Bulb - High PerformanceHigh-performance LED headlight upgrade — 2000 real lumens at a correct 6000K, with an optimized focal point that puts more light on the road.View on eBay →
Yamaha OEM Turn Signal Y-Splitter Connectors, 3-Wire (pair), Type 1Lets you run two sets of rear turn signals at once — these integrated signals plus your OEM or auxiliary signals — on one circuit, no cutting. Sold as a pair.View on eBay →Installation
Designed as a direct replacement for the OEM tail light, with the same fit and electrical connectors — no cutting, splicing, or bodywork required. Full step-by-step instructions are in the collapsible section below and the linked PDF.
Installation instructions (click to expand)
The Custom LED 2015-2024 Yamaha YZF-R3 Blaster-X Integrated LED Tail Light was designed to function as a direct replacement for the OEM tail light. The unit will install with exactly the same fit and electrical connectors as the OEM unit. No cutting, splicing, or bodywork modifications are required, what so ever.
Additional hardware may be necessary if you wish to remove the OEM fender assembly and/or modify the bodywork on your motorcycle. The fender assembly typically supports the license plate and OEM blinker lamps. Keep in mind, our product is a direct replacement for the OEM tail light, and does not require any additional modifications.
There may be additional accessories required to correct blinker problems on your motorcycle if you remove your OEM turn signals. These accessories cannot be built into the tail light, and are generally optional and specific to different customers' needs, so they are sold separately. Please see the Recommended Accessories above, and feel free to contact us with any questions.
Installation requires that you remove the OEM tail light from the motorcycle and install this unit in its place. Please consult a qualified technician or your repair manual for the proper procedure to remove the OEM tail light.
Yamaha YZF-R3 Blaster-X Tail Light — Installation Instructions (PDF)
Custom LED makes Blaster-X tail lights for 100+ motorcycles. Browse the full lineup in our eBay Store to find yours.
Shop all Custom LED Tail LightsWhy Buy From Custom LED
This is a manufacturer-direct purchase straight from Custom LED — designed and assembled in the USA since 2003 — backed by a 2-year warranty and satisfaction guarantee. We ship every order on or before the handling time promised on this listing.
Custom LED • Blaster-X Integrated LED Tail Light • 15FZ07_REV1A_PI2 • Manufacturer Direct