
Infrared Safety Photocell Sensors (safety beams)
Unlike any other on ebay, see below picture to compare!
2 year genuine Australian Warranty
Its worth paying a tiny a bit extra for the best product on ebay!
!!!! Wireless Transmitter battery version now available CLICK HERE !!!!!
- You will receive the 2 piece (sender and receiver) safety photocell system
- Thicker mounting plate with bottom cable entry makes easier installation
Self-contained
surface mount active infrared safety beam for interior of exterior use
Automatic sliding gate ,swing gate ,garage door ,pedestrian door
,industrial door etc
Suitable for universal
installations.
Can Replace any brand of relay type such as
FAAC, CAME, Liftmaster, Magic Button, Ditec, RIB, Fadini, B&D, ATA,
BFT........
- 12-24V AC/DC
- 2 wires, power needed on sender side
- 4 wires, power and output needed on receiver side
WHY BUY OUR SUPERIOR PHOTOCELL?
- Other photocells sold on ebay are inferior and not the same.
- They do not have the same thick base with cable
entry.
- Their cover is made with thinner plastic that will crack when you fit the cover screws
- They cannot handle Australian UV rays and will eventually go brittle and fall apart.
- Their relays are cheap, they will
wear out in 6 months - 1 year, stick and the gate will smash your car.
- Ours have quality fast responding relays, other will delay and your car will be hit.
- We have tested them all and they failed. Ours have been custom manufactured for us, to our quality specifications.
- Do not risk your safety buying a crap product to save a couple dollars
- Others may looks the same outside, but they look closely and they are not.
- We offer 2 years warranty because we are selling the best product available.
- We have been in the gate industry for 30years. We are not toy, torch or comic book sellers.
WHY BUY OUR SUPERIOR PHOTOCELL?
- Other photocells sold on ebay are inferior and not the same.
- They do not have the same thick base with cable
entry.
- Their cover is made with thinner plastic that will crack when you fit the cover screws
- They cannot handle Australian UV rays and will eventually go brittle and fall apart.
- Their relays are cheap, they will
wear out in 6 months - 1 year, stick and the gate will smash your car.
- Ours have quality fast responding relays, other will delay and your car will be hit.
- We have tested them all and they failed. Ours have been custom manufactured for us, to our quality specifications.
- Do not risk your safety buying a crap product to save a couple dollars
- Others may looks the same outside, but they look closely and they are not.
- We offer 2 years warranty because we are selling the best product available.
- We have been in the gate industry for 30years. We are not toy, torch or comic book sellers.
My photocell on the left is much better than the other cheap version on ebay. It has a thicker mounting plate which will not crack,
It also has a bottom cable entry which will allow you to have a conduit with cable underneath
No other photocells on EBAY are like this.

Our quality photocell on Left Standard dodgy photocell on right
What do our customers think?......
All good. Nice positive action on the relay unlike some. Member id janitae 25-Nov-13 21:28
quick postage, nice & neat product (no burrs and sharp edges) clear instruction. Member id ekka2008 25-Nov-13 18:12
Very good item, Fast delivery. Thanks Member id boab1996 18-Nov-13 18:30
I have personally installed hundreds of these and not one has failed.
| Technical Specification | Type |
| Technology | Active infrared |
| Detection Method | Through Beam |
| Sensing Range | 15 meters |
Wave Length
| 940nm |
Infra Red Frequency
| 1.92Khz |
Relay output
| 1Amp max 36V
|
| Supply voltage | 12 -24V AC or DC |
| Dimension | 76mm X 49.2mm X 21.6m
|
Installation Tips:
Apply silicone around sensor mounting plate after installation
It is also good practice to silicone over the 2 front cover screws.
Troubleshooting (Read this before contacting us)
Check
that the voltage polarity is the same on the sender and receiver,
that is left wire is negative right is positive etc. Try switch the
voltage wires and test again.
Test the voltage on the sender and receiver, make sure they are both 12-24v,
If there is 12v or more a red led will light up at the top on sender and receiver
boards.
The output is fail safe and will be NC only if there is power and the beams are talking to each other.
If you see a green led light then they are not communicating or the view is obstructed
Beams must be inline and facing each other.
Payment
Required
within 3 days, If you need more time let me know. Please don't purchase
if you don't intend on paying,
Feedback
I would appreciate if you could leave me 5 stars full positive
feedback in all categories, Ebay considers anything less as negative.
This includes neutral feedback. If you have any problems, issues or
concerns contact me first and I will do my best to solve them. In the
unlikely event you are unhappy with your purchase, return it back to me
for a full refund.
Best value
and quality on ebay!!!
