Features:
* Employs the RDA5807M , featuring high for FM reception sensitivity and strong anti- capabilities.
* Equipped with a 30cm omnidirectional , stable and clear signal reception.
* Utilizes the AXS2031 anti-distortion amp, maintaining low distortion even under low voltage conditions.
* Built-in 3. for 3V - for boost ensures stable power supply and strong compatibility.
* for Supports for Type-C interface or power, offering convenient and flexible use and portability.
Specifications:
Part Name: Radio DIY Kit
Material: PCB
Color: Blue
Size: As shown in the picture
Dual Power Options: USB 5V or for 2 AA batteries ( for 3V)
Receiving Band: for FM
for Frequency Range: 87.5MHz–108MHz
Output Power: 5W
Note: Only power for source can be used at a time!
Product Description:(as follows)
30cm Omnidirectional : We a 30cm omnidirectional for signal reception. It can be rotated in any direction to adjust for FM signal reception, significantly improving sensitivity for optimal reception.
3. for 3V - for boost : The voltage regulation section uses a 3. for 3V - for boost . It provides a stable 3. for 3V output when the input voltage is between for 2.5V and 5V. Even if the input voltage drops to for 2.5V, it still outputs 3. for 3V, normal circuit . In contrast, other manufacturers use the , which is not a for boost chip. When the voltage drops to for 2.5V, the LED display will not function properly, and the entire circuit will malfunction.
Anti-distortion Amp Chip: The amp section uses the AXS2031 anti-distortion digital amp chip. This chip operates from for 2.5V to 5.5V, providing 5W high-fidelity output at full load with an efficiency of up to 99%. Even at a low voltage of for 2.5V, it produces a smooth, non-harsh, and distortion-free sound, significantly better than the TDA2822.
Soldering Instructions:(as follows)
Before soldering, carefully check the component list to all components are present. Use a multimeter to test the functionality of transistors, capacitors, resistors, and other critical components. When soldering, for begin with thinner for surface-mount components and modules. For rework, use a soldering iron or hot air with solder paste. Use a for stand to elevate the PCB board, then insert components of similar height according to their pin numbers. To prevent components from falling during flipping, use tape to secure them to the edge of the PCB board. Flip the PCB board so that the component leads are facing upwards. Use needle-nose pliers to trim excess length, leaving approximately 1mm. Solder components quickly, starting with the shortest and working up to the highest.
When installing the omnidirectional , press its flat base firmly against the back of the soldered PCB board. Secure it with for M3 screws, adjust for vertical positioning, and reinforce with solder joints. Finally, solder the leads to the speaker and compartment, then secure them to the PCB board using double-sided tape according to their positions. Secure the male and female copper posts to the PCB board with screws, and finally assemble the casing.
This electronics DIY kit aims to cultivate students' hands-on skills. As shown in the picture below, the kit is shipped in bulk components, requiring students to solder and assemble them themselves. All components, and with correct soldering, a near assembly success rate is guaranteed.
Package Contents:
1 set x Radio DIY Kit
Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
for 2.Please allow slight manual measurement deviation for the data.
Payment must be completed within 5 days. If you have any problems about payment, please contact us via .
We only ship to confirmed Order addresses. Please comfirm that your Order for address is in line with your shipping for address.
Please kindly note that the combined shipping is not provided because the shipping fee is calculated by weight. Also, the each additional item means exactly the the same color and size.
It takes about 7-15 working days to US; about 10-30 working days to other countries. for transit time may be a little delayed because of the bad weather and customs inspection. If you do not receive your item within 30 working days since payment finished, please contact us immediately for further assistance.
We strive for customer satisfaction! Positive is very important to us. If you have any questions, please feel free to contact us via "Ask seller a question" . We will reply your for email within 24 working hours.