• CV Axles Replacement 
  •  
  • BEFORE YOU INSTALL
  •  
    • Lift vehicle using suitable equipment and safety precautions before installing replacement CV Drive Axle.
    • Check condition of engine and transmission mounts for damage before installing replacement CV Drive axle. 
    • Check condition of suspension and steering components before installing replacement CV Drive axle. 
    • Correct or repair any pre-existing suspension damage or chassis sub frame alignment issues before installing the replacement CV Drive Axle.If the drive train has shifted to one side, the axle might pull out while turning, resulting in catastrophic axle failure. 
     

    • For Yamaha Rhino 450 2006-2009 Rhino 660 2004-2007 Pair Rear Side CV Axles

    CV Axles Replacement 

     

    BEFORE YOU INSTALL

     

    • Lift vehicle using suitable equipment and safety precautions before installing replacement CV Drive Axle.
    • Check condition of engine and transmission mounts for damage before installing replacement CV Drive axle. 
    • Check condition of suspension and steering components before installing replacement CV Drive axle. 
    • Correct or repair any pre-existing suspension damage or chassis sub frame alignment issues before installing the replacement CV Drive Axle.If the drive train has shifted to one side, the axle might pull out while turning, resulting in catastrophic axle failure. 

     

    ?TIPS

     

    • Compare the original and replacement units. Ensure the splines and overall compressed length match the original.
    • Make every effort to prevent debris from contacting operating surfaces or entering bearings. Protect seal surfaces during CV Drive Axle installation.
    • Be sure to replace any damaged fasteners with components of equal or better quality.
    • Be sure to use, as applicable, OE approved fluids, lubricants, adhesives or sealants as specified by the vehicle service manual.
    • If both CV Drive Axles are being replaced, complete the removal and installation on one side before removing the second side. This is very important on some applications such as Fords. Removing both CV Drive Axles may cause the differential gears to become dislocated, requiring disassembly of the transaxle for reassembling of gears.
    • Never over-extend or over-angle a CV Drive Axle joint, as this will cause damage. Keep outer end supported while servicing the inner end of the assembly.
    • Vehicle splines and installation surfaces must be clean. Lubricate CV splines to assist installation. Apply a thin film of grease to CV oil seal contact surfaces.
    • Before operating the vehicle, check transmission lubricant level, refill with correct lubricant as needed.


    content_src_url





    Payment

     

    1.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.

     

     
    2.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    3.Payment must be received within 10 days as auction ended or order might be delayed.

     

    Shipping
     
    1. Orders processed within 24 hours of payment verification.
     
    2. The images shown are not the actual item and are for your reference only.
     
    3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
     
    Returns
     
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging

     

    Contact us

    You may contact us via message if you have any questions and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)

    For Yamaha Rhino 450 2006-2009 Rhino 660 2004-2007 Pair Rear Side CV Axles

    CV Axles Replacement 

     

    BEFORE YOU INSTALL

     

    • Lift vehicle using suitable equipment and safety precautions before installing replacement CV Drive Axle.
    • Check condition of engine and transmission mounts for damage before installing replacement CV Drive axle. 
    • Check condition of suspension and steering components before installing replacement CV Drive axle. 
    • Correct or repair any pre-existing suspension damage or chassis sub frame alignment issues before installing the replacement CV Drive Axle.If the drive train has shifted to one side, the axle might pull out while turning, resulting in catastrophic axle failure. 

     

    ?TIPS

     

    • Compare the original and replacement units. Ensure the splines and overall compressed length match the original.
    • Make every effort to prevent debris from contacting operating surfaces or entering bearings. Protect seal surfaces during CV Drive Axle installation.
    • Be sure to replace any damaged fasteners with components of equal or better quality.
    • Be sure to use, as applicable, OE approved fluids, lubricants, adhesives or sealants as specified by the vehicle service manual.
    • If both CV Drive Axles are being replaced, complete the removal and installation on one side before removing the second side. This is very important on some applications such as Fords. Removing both CV Drive Axles may cause the differential gears to become dislocated, requiring disassembly of the transaxle for reassembling of gears.
    • Never over-extend or over-angle a CV Drive Axle joint, as this will cause damage. Keep outer end supported while servicing the inner end of the assembly.
    • Vehicle splines and installation surfaces must be clean. Lubricate CV splines to assist installation. Apply a thin film of grease to CV oil seal contact surfaces.
    • Before operating the vehicle, check transmission lubricant level, refill with correct lubricant as needed.

    Payment

     

    1.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.

     

     
    2.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    3.Payment must be received within 10 days as auction ended or order might be delayed.

     
    Shipping
     
    1. Orders processed within 24 hours of payment verification.
     
    2. The images shown are not the actual item and are for your reference only.
     
    3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
     
    Returns
     
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging

     

    Contact us

    You may contact us via message if you have any questions and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)


    Copyright of HK-batteries. All rights reserved.