Designed to replace over 120 types of furnace, boiler or water heater igniters.
A universal replacement silicon nitride igniter kit.
Durable new technology with low energy consumption.
PART# HSIURK120VR
Operating Voltage: 120 VAC
Universal Round Igniter Part Number HSIURK120v
Igniter heating element is an all ceramic (Si3N4) product.
It uses complex multi-layer moulding and sintering techniques.
Silicon Nitride heating element
Heater cemented into ceramic insulator using white ceramic cement
Bracket stainless steel 304 - bright finish
Ceramic insulator body non glazed 95% alumina - polished finish
Cable - PTFE U/L Specification - temperature rating 250ºC
Specification
Time to 1200ºC < 6 seconds @ 120 volt
Cold Resistance 16-60 ohms @ 25ºC
Operating Voltage 120 volts +10% -15%
Power Rating 100-160 watts
Fitting Instructions
Please read all these instructions to the end carefully before beginning installation.
1. Identify which type of hot surface igniter is inside your appliance.
2. Unplug your existing igniter, retaining all fittings, and match it up with diagrams above (this can also be done by comparing the top end view of the base type).
3. Compare the position of the ridge on your existing igniter carefully to the top view diagram. Ensure that you have the correct igniter type. Take your time to identify this carefully.
4. Referring to the centre bottom diagram, break off the tabs indicated, preferably with thin nose pliers.
5. Cut off the plug from your appliance, as close to the plug as possible. Make sure there is enough lead to work with. Bare one quarter of an inch of wire.
6. Fit the universal adaptor to the appliance using existing screws. Once the universal adaptor is fitted, screw the igniter into the adaptor, as per the final diagram, using the screw provided.
7. Attach the wires from the appliance onto the igniter, by twisting the bared ends together, matching one wire from the igniter, to one wire from the controller (please refer to diagram).
8. Finally, take the terminal caps provided and screw down tight over the joined bare wires, ensuring that no bare wires are showing. If necessary, the igniter wires can be cut to length.
9.Check installation is secure and safe, routing leads away from the burner.
Commissioning
1. Turn on the gas supply and electrical supply to the appliance.
2. Set the room thermostat for heat.
3. Test furnace for proper ignition and operation.
4. Verify that the Power-On LED, on the power module, is on during the Glo-Stix&; igniter warm-up.
5. During igniter warm-up, using a true RMS voltmeter, measure the voltage across the igniter. Voltage should be between 50 VAC and 120 VAC.
6. Make sure the Glo-Stix&; igniter does not remain energized in the flame for more than a few seconds.
7. Replace the burner compartment door.
8. Place Glo-Stix&; upgrade label on front of the appliance, write the date of installation and your contact details.
|
American Road Equip |
201W |
|
Acro Air |
1096048 | 1380680 |
|
Armstrong Air |
38322B001 |
|
Carrier Corporation |
LH33ZS001A | LH33ZS002 |
|
Claire Brothers |
C-238 | C-242 |
|
Coleman |
1474-051 | 1474-052 |
|
Comfort Maker |
1096048 |
|
Detroit Radiant |
201D |
|
DMO Industries |
20834 |
|
Dornback Furnace |
271W |
|
Ducane |
20015201 |
|
Enerco Tech |
10399 |
|
Evcon |
1474-051 | 1474-052 |
|
Goodman |
B10401009 |
|
Heil |
1096048 |
|
Hupp Industries |
09050 |
|
Intercity |
1009604 | 1096048 |
|
Majestic |
75-92-104 | 75-92-105 |
|
Metzger |
201N | 201W |
|
Mor-Flo |
3200618 |
|
Nordyne |
105141000 | 632-0770 | 632-0880 | 902661 |
|
Norton |
201 | 201D | 201K | 201L | 201R | 201W | 271 |
|
Raypak |
600915 |
|
Rheem |
62-22441-01 | 62-22868-82 | 62-22868-93 |
|
Roberts Gordon |
90434300 | 90436600 |
|
Robertshaw |
41-402 | 41-403 | 41-404 | 41-405 | 41-407 |
|
Smith HB |
50018 |
|
Snyder General |
1380654 | 1380672 | 1380680 |
|
Superior Fireplace |
94851 |
|
Tempstar |
1096048 | 1148245 |
|
Trane Company |
340039P01 | B138196P01 | B144676P01 |
|
Viessman |
9302-094 |
|
Wayne Home Equip |
62821-001 | 62821-002 |
|
Weil McLain |
511-330-139 | 511-330-190 | 511-330-193 |
|
White LB Company |
120-07549 |
|
White-Rodgers |
767A-301 | 767A-303 | 767A-306 | 767A-310 |
|
Williamson |
09050 |
|
York International |
025-27766-000 | 025-27774-000 |
niversal Round Igniter part no. HSIURK120v