eBay

04-13 Yamaha Rhino Angle Tab 1-3/4" Clamp Roll Bar Cage Light Mounting Brackets

2 - All Steel Angled Light Mounting Bracket Clamps - DOM Tubing 1.75" Bar

Listing is for TWO 1.75" Angled Bar Clamps w/ SS Hardware
Light NOT Included!

Our 1.75" Heavy Duty fabricated angled tab round bar mounting clamps are made from DOM (Drawn Over Mandrel) mechanical steel tubing and hand tig welded for strength and good looks. They are finished off with a semi-gloss powder coat finish and feature all stainless steel hardware. We manufacture these right here in the U.S.A. Our clamps are machined on all surfaces including the inner diameter to ensure a nice fit.

These light mounting clamps are designed to mount lights on the front angled tubes of the roll-cage passenger compartment. We have design these mounting brackets to clamp on so you have the ability to install them anywhere along the the front angled bar. The mounting bracket pictured below, with the off-road light, has been fitted with a 7" internal ballest HID light. So just about any size light will fit on this mounting bracket. Mounting hole is 1/2" diameter.

These are some of the nicest and strongest clamps available. They feature recessed bolt holes for the cap screws and blind threaded holes on the mating side for a smooth clean look. The back side of the clamp is completely smooth, not only giving the clamp great looks, but this allows the tab to be welding to the clamp with a very clean look.

Listing is for TWO - 1.75" angled clamps to be used with 1.75" round tubing that is on an angle. Approx. 35 degrees.

**Note: A question we get asked often:

Q: Is there suppose to be a gap between the two clamp halves when installed?
A: Yes, these clamps are made for DOM tubing. This is the result of cutting tubing into two pieces, material is removed. This also insures you are able to get the clamp tight! If the clamp halves touch and bottom out, there is no guarantee you really have them tight!

MADE IN U.S.A - Made here in Southern California, USA.
Not a cheap over seas piece. Clamps come powder coated semi-gloss black...

Specifications:

Clamp O.D. = 2.5"

Clamp I.D. = 1.75"

Clamp Width = 1.75"

Clamp Thickness = 3/8"

Tab Mounting Hole = 1/2"

Tab Thickness = 1/8"

Applications:

All 1.75" [1-3/4"] Round Tubing / Bar (Tab Welded @ Approx 35 degrees)

Factory Roll Cage Tubing Diameters:

(Reference ONLY - Check Your Ride!!!!)

Arctic Cat
- Wildcat - 1.75"
- Prowler (round aftermarket cage only)
Can Am
- Commander Cage - 2"
Honda
- Big Red - 1.625"
Kawasaki
- Teryx
  - Perimeter - 1.875”
  - Top Crossbars - 1.75”
- Teryx 4
  - Perimeter - 1.875”
  - Top Crossbars - 1.75”
Polaris
- Ranger
  - Perimeter - 1.75”
  - Top Crossbars - 1.75”
  - Harness Bar & Rear Bumper Crossbars - 1.5”
- RZR, S & XP
  - Perimeter - 1.75”
  - Top Crossbars - 1.75”
  - Harness Bar & Rear Bumper Crossbars - 1.5”
- RZR 4 & XP 4
  - Perimeter - 1.75”
  - Top Crossbars - 1.75", 1.5" & 1.25"
  - Rear Harness Bar & Bumper Crossbars - 1.5”
Redline
- Revolt - 1.25"
- Riot - 1.50"
Yamaha
- Rhino
  - Perimeter - 1.75”
  - Rhino Top Crossbars - 1.5”

** SEE OUR OTHER LISTINGS FOR OTHER MODELS:

ALSO AVAILABLE FOR STRAIGHT VERTICAL AND HORIZONTAL BARS.
GREAT FOR LIGHTS, WHIPS OR OTHER ACCESSORIES.

Part # SSM-DOM-4-BC-ANG-175-Qty-2