802540 Lithium-ion polymer battery (LiPo) (3.7V 800mAh) 3 pin Each cell outputs a nominal 3.7V. These batteries have fast charge times, can reliably hold a charge, and have built-in safety circuitry. These batteries are compatible with the PiJuice. The PiJuice Zero HAT doesn't come with a standard onboard battery.

Model series Info 802540 7.65= Thickness 23 = Width, 40.5 = length + or -5%

Lithium-ion polymer (also known as 'lipo') batteries are thin, light and powerful. The output ranges from 4.2V when ultimately charged to 3.7V. This battery has a capacity of 800mAh for a total of about 2.96Wh. If you need a larger (or smaller!) battery, we have an extensive range of Lithium-ion polymer batteries.

Protection circuitry keeps the battery voltage from going too high (over-charging) or low over-discharge, which means that the battery will cut out when completely dead at 3.0V. It will also protect against output shorts. Even with this protection, it is essential that you only use a LiPo constant-voltage/current charger to recharge them at 0.5C or less. Tempero Systems suggests charging at 0.5C or even less, 400mA max for this battery. Like most lipos, These batteries do not have thermistors built in.

The batteries come pre-attached with a 3-pin JST-PH connector and include the necessary protection circuitry. The JST-PH connector has 2.0mm spacing between its pins.

Note:  this is a generic LiPo battery compatible with PiJuice by using a custom profile in the PiJuice configuration software. The standard PiJuice battery profiles may not work as intended with this battery

Specifications:
  • Model: 802540
  • Battery Chemical Composition: Lithium-Ion
  • Nominal Voltage: 3.7v
  • Nominal Capacity: 800mAh
  • Battery Watt Hour Rating (Required for Lithium Batteries):2.96Wh
  • Max charge current: 1C
  • Cut-off Voltage: 2.75v +-5%
  • Standard Charging method: 0.5C CC (constant current) charge to 4.2V, then CV (constant voltage 4.2V) charge till charge current decline to ≤0.01C
  • Discharging method: Constant current 0.2 C end voltage 2.75V.
  • Charge Current: 0.2C = 160mA
  • Maximum Charge Current: 0.5C = 400mA
  • Max discharge current: 1C
  • Cut-off Voltage: 3.0V
  • C.V: ≥3.85V
  • Connection Type: JST PH 2.0MM
  • Onboard NTC Temperature Sensor
  • Dimension: Thickness x Width x Height 7.65x23x40.5 mm
  • Weight: 14.85 Grams
  • Cycle Life: Over 500 times
  • Operating Environment: Charging: 0°C~45°C;65±20RH
  • Operating Environment: Discharging: 10°C~60°C;65±20RH
  • Storage temperature: -5℃~35℃
  • Charging Attention: Charging current and charging voltage should be less than specified.
  • Dangerous Road Freight: NO
  • Dangerous Air Freight: YES
Usage & Precaution:

Lithium-ion and lithium polymer cells are very powerful batteries, and YOU should take extreme care. Using them may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Unfortunately, we can not replace batteries damaged by non-compliant chargers or equipment.
Be sure to follow the safety warnings listed below:

Do not
  • overcharge Ensure the charger voltage does not exceed the battery's stated full charge voltage.
  • over-discharge Ensure the equipment you use this battery in will not draw more current from that battery than the stated "Maximum Continuous Discharge Current."
  • leave batteries discharged for an extended period can incur irreversible damage
  • Place the battery on fire, heating, or direct sunlight to the battery.
  • Install the battery backwards, so the polarity is reversed.
  • Connect the battery's positive and negative terminal with any metal object,
  • Expose the battery to water or saltwater, or let the battery get wet.
  • Disassemble or modify the battery. The battery contains safety and protection devices.

Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. As with all Lithium-ion polymer batteries and any power source - they should be used by experts who are comfortable working with power supplies.

Package included: 1x 802540 Lithium ion polymer Battery (LiPo) (3.7V 800mAh) 3 pinPlease Note: 

Due to continued product development, specifications are subject to change without prior notice
Product may vary from pictures due to product enhancement/supply

Please read conditions of sale before purchasing

****Postage/Shipping details****

All stock is based on Gold Coast and is shipped with Australia Post 

Local Pick up is available (We are located in Southport, Queensland, QLD. Please contact us to make an appointment.)

Standard delivery (3~12 days) 

Express delivery (1~3 days)

 Most items will reach on time, however it may be delayed by Australia Post

After received your clear payment, the product will be post to you within 2 working days.

In case the parcel delayed or lost during the delivery, please contact us, we will do our best to help you out. 

But it's unfair for us to take the negative feedback due to the fault of a third part.

****Payment details****

1. We only accept PayPal Or  Ebay Payments 

2. Please ensure you supply the correct shipping address 

****Return Policy****

1. We accept returns within 30 days of purchase

2. Shipping and handling fees are not refundable, buyer is responsible for return shipping costs

****Customer Service****

Before or After-sale service:

If you have any question or problem, please feel free to contact.

???Feedback???

We value our feedback. Your positive feedback is highly appreciated.

If you are not completely satisfied with our products or service, please contact before leaving feedback. We will do our best to solve every problem and reach your satisfaction.

Hope you enjoy shopping with us!

****About Us****

We are a small business based in Queensland  here to provide fast and quality services to customers. 

We aim to provide the best quality item for the lowest price