Description:
AUTOOL CT60 is used to test automobile injectors to determine whether the fuel injectors are stuck, leaking, or burning. It is possible to set multiple pulse outputs and adjust speed, pulse width, operating time and other parameters as required. It is also possible to connect two nozzles for the simultaneous operation to compare the sprayability status and the spray angle of the fuel injector.
AUTOOL CT60 is used to test automobile injectors to determine whether the fuel injectors are stuck, leaking, or burning. It is possible to set multiple pulse outputs and adjust speed, pulse width, operating time and other parameters as required. It is also possible to connect two nozzles for the simultaneous operation to compare the sprayability status and the spray angle of the fuel injector.
Features:
1.Easily solve common faults such as stuck, blocked, leaked, or insufficient combustion of the fuel injector.
2.Three-year warranty and lifetime maintenance.
3.The pulse width and RPM can be continuously adjusted and different programs can be applied to drive the injectors.
4.During the cleaning process, pulse cleaning can be achieved by adjusting the RPM and width to optimize the cleaning effect.
Can be used with any fuel pressure tester.
5.This device can also be used with ultrasonic cleaners and older fuel injector testers. The drive mode of the GDI engine injector added to this machine can be used as an upgrade kit for the old version of the machine (machine without GDI drive).
How to use:
1. Turn off the engine of the vehicle and remove the injector on the engine
2. Connect the pulse output terminal to the power input port on the injector
3. Connect the positive and negative poles of the battery clip to the 12V battery
4. Press the speed "+" and "-" keys, select the desired simulated speed, and press the start button. The injector starts to work
5. Select the required injector connection equipment
6. Put the fuel injector into the connecting device, and then press the carburetor cleaner
7. Press the speed "+" and "-" keys, the tester will output pulses to the injector, and then the pulse signal indicator will light up; the injector starts to switch.
8. Use the cleaning fluid with its own pressure, you need to select the corresponding connection joint and connect it, press the start button, and the oil will start to be sprayed. Use your eyes to observe the atomization state of the spray and whether there is any problem with the spray angle.
Parameters:
Name | AUTOOL CT60 |
Power input | 12V |
Operating environment | 0℃-60℃，Relative humidity<80％ |
Storage environment | -10℃-60℃，Relative humidity<85％ |
Weight（g） | 200 |
Size（mm） | 150×90×50 |
Notice:
1. Before using this instrument, the car engine must be turned off.
2. Do not smoke or ignite near the car.
3. Don't splash the fuel of the car on the hot engine parts.
4. Use this instrument only in a ventilated place.
5. Don't get close to any car's rotating parts, and don't touch any car's heating parts.
6. Do not touch any car parts with dangerous voltage.
7. Wear qualified goggles.
8. After the test is completed, all disconnected car connections should be correctly restored.
Package Includes:
1pc* AUTOOL CT60 Automotive Injector Tester main unit
1pc* Power supply adapter
1pc* User manual
1pc* Injector connector
1pc* Connection line
1pc* Power supply cable
1. Before using this instrument, the car engine must be turned off.
2. Do not smoke or ignite near the car.
3. Don't splash the fuel of the car on the hot engine parts.
4. Use this instrument only in a ventilated place.
5. Don't get close to any car's rotating parts, and don't touch any car's heating parts.
6. Do not touch any car parts with dangerous voltage.
7. Wear qualified goggles.
8. After the test is completed, all disconnected car connections should be correctly restored.
Package Includes:
1pc* AUTOOL CT60 Automotive Injector Tester main unit
1pc* Power supply adapter
1pc* User manual
1pc* Injector connector
1pc* Connection line
1pc* Power supply cable
