$$$$$ FREE SHIPPING TO LOWER 48 STATES ONLY $$$$$
Features, Advantages, & Benefits
- GENUINE FORD RACING PERFORMANCE PART
- GREAT FOR RESTORATION REPAIR PROJECTS! JUDGED SHOWS STREET/TRACK DUTY!
- HIGH QUALITY REPLACEMENT THAT IMPROVES BRAKING PERFORMANCE FOR YOUR FOX!
- LIGHT WEIGHT BILLET ALUMINUM MADE IN USA!
- FULLY ADJUSTABLE FROM 100-1000PSI
- FORD RACING LOGO GENUINE FORD RACING PART #M-2328-C
- FITS 1979-1993 FORD MUSTANG GT / LX 5.0L
- Allows Adjustment Of Fluid Pressures To Correct Brake Bias
- MADE IN USA! IT MATTERS, NOT TO SUPPORT THE CHICOMS!
IN THE BOX
- (1) GENUINE FORD RACING PART #M-2328-C PROPORTIONING VALVE
Product Description
Ford Performance Mustang Propotioning Valve
The Ford Performance M-2328-C Adjustable Proportioning Valve is cast from lightweight aluminum (only .5lb!) & is compact in design. It allows adjustment of fluid pressure to correct rear brake bias. The “Kneepoint” is adjustable from 100-1000psi. The housing has inlet and outlet ports with 1/8-27 NPT (National Pipe Thread) threads for maximum installation flexibility & includes the needed adapters to be a direct install for 79-93 Mustang. MADE IN USA! - MADE IN USA! IT MATTERS, NOT TO SUPPORT THE CHICOMS!
INSTALLATION & ADJUSTMENTS
Proportioning valves are normally installed in the rear fluid line to prevent the rear wheels from locking before the front wheels, or to give a driver the ability to make fine adjustments in front to rear bias percentage on the track to compensate for tire wear, fuel load burn-off, or changing track conditions. It is generally not recommended to attempt to reduce front wheel braking capacity.
Use only the two .25" body holes to secure the valve to a mount. Do not attempt to remove the adjuster knob or valve body end cap to facilitate thru-panel mounting.
Two 1/8-27 NPT to 3/8-24 inverted flare fittings are supplied to adapt double flared hard brake lines to the valve. Connect the "IN" port to the pressure line coming from the master cylinder. Connect the line going to the calipers to the "OUT" port.
The adjusting knob is marked with an arrow indicating the direction required to decrease line pressure to the calipers. The knob rotated all the way out (counter-clockwise) will provide a maximum pressure reduction of 57%. Rotating the know in (clockwise) will incrementally increase line pressure, up to full pressure. If the range of adjustment in the valve is not sufficient to properly balance the vehicle’s bias, changes to other components within the system may be necessary.
MADE IN USA!
TESTING THE SYSTEM
Do not attempt to operate the vehicle until the system has been fully tested under controlled conditions in a safe location. After the system has been bled, checked for leaks, and the proper pedal resistance and travel have been determined, make a series of low speed stops, then gradually progress to normal operating speeds.
WARNING
Adjustable proportioning valves are designed for tuning and balancing custom brake systems on performance, racing, and other types of special purpose vehicles. They are NOT designed as direct replacements for any OEM application.
WARNING
It is the responsibility of the person installing any brake component or kit to determine the suitability of the component or kit for that particular application. If you are not sure how to safely use this brake component or kit, you should not install or use it. Do not assume anything. Improperly installed or maintained brakes are dangerous. If you are not sure, get help from a professional certified automotive technician. You, or the person who does the installation must know how to properly use this product. It is not possible over the internet, email, or the phone to understand or foresee all the issues that might arise in your installation. Racing equipment and brakes must be maintained and should be checked regularly for fatigue, damage, and wear. BUYER ACCEPTS ALL RESPONSIBILITY FOR THE INSTALLATION AND USE OF THIS PRODUCT.
* THIS IS AN OUTSTANDING QUALITY PRODUCT, BUT YOU MUST KNOW WHAT YOU ARE DOING TO PROPERLY INSTALL AND SAFELY ADJUST IT. TAKE OUR ADVICE AS A SHOP, SEEK A PROFESSIONAL TO ENSURE YOU HAVE A SAFE BRAKING SYSTEM.
APPLICATION / VEHICLE FITMENT:
FITS 1979-1993 FORD MUSTANG GT / LX 5.0LThank you for considering this item!