Alignment, Gimbal, Hinge Pin Boat Tools for Mercruiser Alpha, OMC, Bravo
This is a set of Five (5) Tools:
-
Engine Alignment Tool;
-
Drive Shaft Bellow Sleeve Installation Tool (PVC Plastic);
-
Gimbal Bearing Installation Tool;
-
Grease Seal Installation Tool;
-
Hinge Pin Tool (OEM 91-78310).
Engine Alignment Bar Tool compatible with MerCruiser Sterndrives including: Pre-Alpha "R", Alpha One "MR", Generation II, all Bravo models. This Tool is similar to MerCruiser P/N 91-805475A1 which used to be P/N 91-57797A3. Compatible with Volvo SX P/N 3851083 and OMC Cobra P/N 18-4442. The length of the bar is approximately 23-5/8 inch. Tool is made from high quality 1045 Steel, and includes an eyebolt which gives you the option of hanging the tool. Alignment Tool Comes Without Black Oxide Coating.
Alignment Tool will correctly align all OMC Cobra and Mercruiser Outdrives with the exception of the Mercruiser TR and TRS Outdrive Models.
The Bellow Ring/ Retainer Sleeve Installation Tool made of PVC Plastic. Drive Shaft Bellow Sleeve Installation Tool helps install the aluminum ring into the Alpha 1 Generation 2, Bravo, Blackhawk U-Joints Bellows. This tool is an aftermarket OEM part that replaces Mercury Mariner 91-818162.
Gimbal Bearing Installation Tool. This tool compatible with OMC Cobras, Bravos, #1 Drives made from 1966 to Current makes, including the Pre Alpha (R), Alpha 1 “MR” and Generation 2. You will need the Outdrive Coupler Alignment Tool to use this tool. Note: This requires a hole drilled in your alignment tool. We cannot pre-drill these as different manufacturers make the mounts in different places. The tool comes with directions on where to drill the hole in the alignment tool for correct lineup. Tool comes with black oxide finish preventing corrosion to assure many years of service.
Grease Seal Installation Tool. Used on all Mercruiser #1 Drives, Pre Alpha (R), Alpha One (MR), Generation 2, All Bravos, and OMC Cobras. This seal installer will allow you to drive the grease seal in straight for proper installation.
Hinge Pin Tool (OEM 91-78310). The material is 4140 Hardened Tool Steel equivalent to Grade 8 With a minimum Rockwell hardness of C33 and minimum tensile strength of 150,000 psi. This tool is used on the hinge pin bolt and separates the housing from the gimbal ring. This tool compatible with MerCruiser Sterndrives: Alpha One, Alpha One Generation Two, Bravo One, Bravo Two, Bravo Three, R, MP, MC-1. This tool replaces MerCruiser OEM: 91-78310.
All tools are professionally made in the United States on the state of the art CNC equipment with 100% quality inspection.
-
We offer combined shipping services.
-
Orders received before 1:30 PM Central Time, Monday to Friday, excluding holidays, will be shipped the same day. Any order received after 1:30 PM Central Time, will be processed the following business day.
-
All our tools are made from high quality materials and are designed for long life durability and ease of use.
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
We offer COMBINED shipping on all orders!
Your order will be sent within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it within one to four business days.
In the very unlikely event that your item is lost or damaged on its way to you, then WE are responsible and will issue either a full refund or replacement
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 30 days from the date you purchased it.
Alignment, Gimbal, Hinge Pin Boat Tools for Mercruiser Alpha, OMC, Bravo
This is a set of Five (5) Tools:
-
Engine Alignment Tool;
-
Drive Shaft Bellow Sleeve Installation Tool (PVC Plastic);
-
Gimbal Bearing Installation Tool;
-
Grease Seal Installation Tool;
-
Hinge Pin Tool (OEM 91-78310).
Engine Alignment Bar Tool compatible with MerCruiser Sterndrives including: Pre-Alpha "R", Alpha One "MR", Generation II, all Bravo models. This Tool is similar to MerCruiser P/N 91-805475A1 which used to be P/N 91-57797A3. Compatible with Volvo SX P/N 3851083 and OMC Cobra P/N 18-4442. The length of the bar is approximately 23-5/8 inch. Tool is made from high quality 1045 Steel, and includes an eyebolt which gives you the option of hanging the tool. Alignment Tool Comes Without Black Oxide Coating.
Alignment Tool will correctly align all OMC Cobra and Mercruiser Outdrives with the exception of the Mercruiser TR and TRS Outdrive Models.
The Bellow Ring/ Retainer Sleeve Installation Tool made of PVC Plastic. Drive Shaft Bellow Sleeve Installation Tool helps install the aluminum ring into the Alpha 1 Generation 2, Bravo, Blackhawk U-Joints Bellows. This tool is an aftermarket OEM part that replaces Mercury Mariner 91-818162.
Gimbal Bearing Installation Tool. This tool compatible with OMC Cobras, Bravos, #1 Drives made from 1966 to Current makes, including the Pre Alpha (R), Alpha 1 “MR” and Generation 2. You will need the Outdrive Coupler Alignment Tool to use this tool. Note: This requires a hole drilled in your alignment tool. We cannot pre-drill these as different manufacturers make the mounts in different places. The tool comes with directions on where to drill the hole in the alignment tool for correct lineup. Tool comes with black oxide finish preventing corrosion to assure many years of service.
Grease Seal Installation Tool. Used on all Mercruiser #1 Drives, Pre Alpha (R), Alpha One (MR), Generation 2, All Bravos, and OMC Cobras. This seal installer will allow you to drive the grease seal in straight for proper installation.
Hinge Pin Tool (OEM 91-78310). The material is 4140 Hardened Tool Steel equivalent to Grade 8 With a minimum Rockwell hardness of C33 and minimum tensile strength of 150,000 psi. This tool is used on the hinge pin bolt and separates the housing from the gimbal ring. This tool compatible with MerCruiser Sterndrives: Alpha One, Alpha One Generation Two, Bravo One, Bravo Two, Bravo Three, R, MP, MC-1. This tool replaces MerCruiser OEM: 91-78310.
All tools are professionally made in the United States on the state of the art CNC equipment with 100% quality inspection.
-
We offer combined shipping services.
-
Orders received before 1:30 PM Central Time, Monday to Friday, excluding holidays, will be shipped the same day. Any order received after 1:30 PM Central Time, will be processed the following business day.
-
All our tools are made from high quality materials and are designed for long life durability and ease of use.
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
We offer COMBINED shipping on all orders!
Your order will be sent within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it within one to four business days.
In the very unlikely event that your item is lost or damaged on its way to you, then WE are responsible and will issue either a full refund or replacement
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 30 days from the date you purchased it.
