Description
1228-2908 (24V 110A) Motor Controller High Quality Permanent Magnetic D.C. Motor Controller for CURTIS 1228 Series
Description:
- For Curtis 1228 motor controller is a permanent magnet motor speed controller designed for use in mobility aid scooters and other small electric vehicles, such as sweeper/scrubbers. It offers smooth, silent, cost effective control of motor speed and torque. A four quadrant, full bridge power output stage provides for solid state motor reversing and full braking power without additional relays or contactors.
- The 1228 controller is fully programmable by means of the handheld programmer for Curtis 1313. Use of the programmer offers diagnostic and test capability as well as configuration flexibility.
Specifications:
- Nominal input voltage: 24 V
- PWM operating frequency: 15 kHz
- Dielectric resistance: >1M ohm (DC test)
- Electrical isolation to heatsink (min.): 500V
- Minimum motor resistance: 130m ohm (110 amp models)
- B+, B- logic pin current (max.): 9A (pins 1, 2 and 10, 11 on 18-pin connector)
- KSI input current (typical): 50mA without programmer; 150mA with programmer
- KSI input current (peak): 1.5A
- Logic input current (typical): 1mA at 24 V
- Horn output current (max.): 15mA
- BDI output voltage and current (max.): 0 - 5 V, 2mA
- LED output current (max.): 15mA
- Electromagnetic brake coil resistance: 32 - 200ohm
- Electromagnetic brake current (max.): 1A
- Control input switch type: on/off
- Speed control signal: 3-wire, 5kohm; or 0 - 5V
- Speed control type: single-ended, inverted single-ended, wigwag, or inverted wigwag
- Operating ambient temperature range: -25°C to 45°C (-13°F to 113°F)
- Storage ambient temperature range: -40°C to 75°C (-40°F to 167°F)
- Heatsink over-temperature cutback: linear cutback starts at 92°C (198°F); complete cutoff at 134°C (273°F)
- Heatsink under-temperature cutback: 50% armature current at -25°C (-13°F)
- Package environmental rating: IP40
- Weight: 0.6kg
- Dimensions (L x W x H): 156 x 91 x 43mm
- Regulatory compliance: designed to ANSI RESNA WC 14/21, ISO 7176-14, ISO 7176-21, and EN 12184.
Package Included:
- 1 x Motor Controller
Description:
- For Curtis 1228 motor controller is a permanent magnet motor speed controller designed for use in mobility aid scooters and other small electric vehicles, such as sweeper/scrubbers. It offers smooth, silent, cost effective control of motor speed and torque. A four quadrant, full bridge power output stage provides for solid state motor reversing and full braking power without additional relays or contactors.
- The 1228 controller is fully programmable by means of the handheld programmer for Curtis 1313. Use of the programmer offers diagnostic and test capability as well as configuration flexibility.
Specifications:
- Nominal input voltage: 24 V
- PWM operating frequency: 15 kHz
- Dielectric resistance: >1M ohm (DC test)
- Electrical isolation to heatsink (min.): 500V
- Minimum motor resistance: 130m ohm (110 amp models)
- B+, B- logic pin current (max.): 9A (pins 1, 2 and 10, 11 on 18-pin connector)
- KSI input current (typical): 50mA without programmer; 150mA with programmer
- KSI input current (peak): 1.5A
- Logic input current (typical): 1mA at 24 V
- Horn output current (max.): 15mA
- BDI output voltage and current (max.): 0 - 5 V, 2mA
- LED output current (max.): 15mA
- Electromagnetic brake coil resistance: 32 - 200ohm
- Electromagnetic brake current (max.): 1A
- Control input switch type: on/off
- Speed control signal: 3-wire, 5kohm; or 0 - 5V
- Speed control type: single-ended, inverted single-ended, wigwag, or inverted wigwag
- Operating ambient temperature range: -25°C to 45°C (-13°F to 113°F)
- Storage ambient temperature range: -40°C to 75°C (-40°F to 167°F)
- Heatsink over-temperature cutback: linear cutback starts at 92°C (198°F); complete cutoff at 134°C (273°F)
- Heatsink under-temperature cutback: 50% armature current at -25°C (-13°F)
- Package environmental rating: IP40
- Weight: 0.6kg
- Dimensions (L x W x H): 156 x 91 x 43mm
- Regulatory compliance: designed to ANSI RESNA WC 14/21, ISO 7176-14, ISO 7176-21, and EN 12184.
Package Included:
- 1 x Motor Controller
Payment Terms
1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
Return Terms
If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund.
Custom Duties & Taxes
1. It is buyer's responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
Feedback
1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
Am 04.09.2024 hat der Verkäufer die folgenden Angaben hinzugefügt:
Am 16.09.2024 hat der Verkäufer die folgenden Angaben hinzugefügt:
Am 05.11.2025 hat der Verkäufer die folgenden Angaben hinzugefügt: