RCWL-0515+microwave induction module

RCWL-0515+is a microwave induction module that uses Doppler radar technology to detect object movement. Adopting 2.7G microwave signal detection, this module has the characteristics of high sensitivity, long sensing distance, strong reliability, large sensing angle, and wide supply voltage range.

Microwave induction is a new type of dead angle free induction mode based on the principle of Doppler radar. Its planar antenna emits electromagnetic waves and receives reflected echoes, which can effectively suppress the interference of higher-order harmonics and other clutter; Compared with infrared products, microwave switches have strong reliability, safety, and convenience. They have a wider sensing distance and no dead zone, and can penetrate glass and thin wooden boards. Depending on the power, they can penetrate walls of different thicknesses without being affected by environment, temperature, dust, etc. The sensing distance will not be shortened at 37 degrees Celsius. Widely used in various occasions such as human body induction lighting and anti-theft alarms.

 

Main characteristics

• Working voltage: 4-18V

• Working current: 4mA

• 2.7G operating frequency

• Reserved patch and inline CDS interface

• 12 meter typical sensing range

• Adjustable sensing distance

• Lead-free process

• Adjustable repeat trigger time

 

 

Typical Applications

• Corridor light, induction light, solar light

• UV antivirus lamp

• Human motion sensing

 

Board header
• 3V3: 3.3V regulated output. Max 100mA
• GND: Ground
• OUT: Trigger: high (3.3V) if motion detected. 0V normally.
• VCC: 4 - 18V supply voltage
• CDS: Trigger control signal; less than 0.7V, OUT- - direct output low level: greater than 0.7V, positive detection
work often. 

 

 

RCWL-0516+microwave induction module

Product Overview: RCWL-0516+is a microwave induction module that uses Doppler radar technology to detect object movement. Adopting 2.7G microwave signal detection, this module has the characteristics of high sensitivity, long sensing distance, strong reliability, large sensing angle, and wide supply voltage range.

RCM-0516 hardware size is fully compatible with RNL-0516. The main upgrades are as follows:

1: Adopting lead-free process, meeting environmental requirements

2: Improve detection sensitivity up to 10-15 meters RCL0516 at 5-8 meters

3: Adopting digital processing chip RCL0001; Stronger anti-interference

4: Increase the maximum working voltage to 25V (RCWL-0516 maximum 18V)

 

 

Main characteristics

• Working voltage: 3.3-25V

• Working current: 3mA

• Lead-free process

• Reserved patch and inline CDS interface

• Typical sensing range of 10-15 meters

• Adjustable sensing distance

• Lead free process 2.7G working frequency

• Adjustable repeated triggering time, with a minimum triggering time of 2 seconds

 

 

Typical Applications

• Corridor light, induction light, solar light

• UV antivirus lamp

• Human motion sensing

 

 

Pin Definition:

1.3V3:3V3 power output

2.GND:ground

3.OUT:OUT: Trigger: high (3.3V) if motion detected. 0V normally

4.VIN:input voltage,3.3-25V

5.CDS:enable control chip,lower than 0.7V,OUT will output low level all the time

 

 

 

 

 

 

 

RCWL-0516+microwave induction module

RCWL-0516+is a microwave induction module that uses Doppler radar technology to detect object movement. Adopting 2.7G microwave signal detection, this module has the characteristics of high sensitivity, long sensing distance, strong reliability, large sensing angle, and wide supply voltage range.

The hardware size of rcm-0516 is fully compatible with rnl-0516, and the main upgrades are as follows:

1: Adopting lead-free process to meet environmental requirements

2: Improve detection sensitivity up to 10-15 meters, RCL-0516 at 5-8 meters

3: Adopting digital processing chip RCL0001; Stronger anti-interference

4: Increase the maximum working voltage to 25V (RCWL-0516 maximum 18V)

 

 

Main characteristics

• Working voltage: 3.3-25V

• Working current: 3mA

• Lead-free process

• Reserved patch and inline CDS interface

• Typical sensing range of 10-15 meters

• Adjustable sensing distance

• Lead free process 2.7G working frequency

• Adjustable repeated triggering time, with a minimum triggering time of 2 seconds

 

Typical Applications

• Corridor light, induction light, solar light

• UV antivirus lamp

• Human motion sensing

 

 

Pin Definition:

1.3V3:3V3 power output

2.GND:ground

3.OUT:OUT: Trigger: high (3.3V) if motion detected. 0V normally

4.VIN:input voltage,3.3-25V

5.CDS:enable control chip,lower than 0.7V,OUT will output low level all the time