CONENSET | REPLACEMENT BATTERY
For Tronsmart Halo 100 / 110
Party Speaker
Party Speaker
7.2V · 6000mAh · Li-Ion · Model 4S1P
Highlights
| ✓ | Direct replacement battery pack for Tronsmart Halo 100 and Tronsmart Halo 110 party speakers |
| ✓ | 7.2V 6000mAh capacity — brings back the playtime when your original pack no longer holds a charge |
| ✓ | Model 4S1P Li-ion rechargeable pack, produced to standard GB/T 18287-2000 |
| ✓ | Pre-wired with plug connector (red / white / black leads) — unplug the old pack and plug this one in |
| ✓ | Brand new, individually packed — a low-cost fix instead of replacing the whole speaker |
Specifications
| Brand | CONENSET |
| Model / Configuration | 4S1P |
| Battery Chemistry | Li-Ion (Lithium-Ion) Rechargeable |
| Voltage | 7.2V |
| Capacity | 6000mAh |
| Product Standard | GB/T 18287-2000 |
| Connector | Pre-wired, 3 leads (red / white / black) with plug |
| Condition | Brand New |
| Country of Manufacture | China |
Compatibility
| Fits Model | Tronsmart Halo 100 Party Speaker |
| Fits Model | Tronsmart Halo 110 Party Speaker |
| Original Spec Replaced | 7.2V / 6000mAh Li-ion pack (4S1P) |
Please check before you buy: open your speaker and compare your original battery pack with the photos above — voltage, capacity (mAh), pack shape and the number of leads / plug type must match. If you are not sure, message us with a photo of your old pack and we will confirm for you.
When to Replace the Battery
| ✓ | Playtime has dropped noticeably and the speaker needs charging far more often |
| ✓ | The charge indicator jumps or the speaker shuts down even when "fully charged" |
| ✓ | The pack no longer accepts a charge at all, or the housing looks swollen |
| ✓ | The speaker only works while plugged into the mains |
Fitting Tips
| 1. | Power the speaker off, unplug the charger and let it stand for a few minutes before opening it. |
| 2. | Take a photo of the wiring and connector orientation before you unplug the old pack. |
| 3. | Keep the lead colours in the same positions as the original (red / white / black) — never reverse polarity. |
| 4. | Secure the pack so it cannot move or press against the board, then close the housing and charge fully before first use. |
| 5. | Not confident with wiring? Have the pack fitted by a qualified technician. |
Safety & Warnings
• Do not short-circuit, squeeze or collide the battery.
• Do not disassemble the battery.
• Do not throw it into water or put it into water.
• Do not connect improperly — observe correct polarity.
• Do not dispose of in fire or expose to excess heat.
• Do not crush, puncture, incinerate or short-circuit the external contacts.
• Keep away from children. Dispose of used batteries in accordance with your local regulations.
What You Get
| ✓ | 1 x Li-ion replacement battery pack — 7.2V, 6000mAh, model 4S1P, pre-wired with plug connector |
| ✓ | Protective packaging for safe transit |
Shipping & Returns
• Orders are dispatched to the address shown on your eBay order — please check it before paying.
• Delivery time and postage cost are shown on this listing's shipping tab.
• Damaged or faulty on arrival? Message us through eBay and we will put it right.
• Return terms are as stated in this listing's returns policy.
This is a third-party replacement battery pack. It is not manufactured, supplied or endorsed by Tronsmart. "Tronsmart", "Halo 100" and "Halo 110" are trademarks of their respective owner and are used here only to describe compatibility. All measurements are as stated on the manufacturer's label; please verify against your original part before ordering. Colours may vary slightly between production batches.
CONENSET
Thank you for looking — please confirm compatibility before you buy.