• Fit For:
    • 1985-1989 Buick Electra
    • 1986-1999 Buick LeSabre
    • 1991-1996 Buick Park Avenue
    • 1985-1993 Cadillac Commercial Chassis
    • 1985-1993 Cadillac DeVille
    • 1985-1992 Cadillac Fleetwood
    • 1992-1999 Oldsmobile 88
    • 1985-1996 Oldsmobile 98
    • 1986-1991 Oldsmobile Delta 88
    • 1996-1998 Oldsmobile LSS
    • 1997-1998 Oldsmobile Regency
    • 1987-1999 Pontiac Bonneville
     
  • Package Includes:

    • 12 Pcs Front Lower Sway Bar Suspension Kit For 1986-1999 Buick LeSabre 3.8L

    Fit For:

    • 1985-1989 Buick Electra
    • 1986-1999 Buick LeSabre
    • 1991-1996 Buick Park Avenue
    • 1985-1993 Cadillac Commercial Chassis
    • 1985-1993 Cadillac DeVille
    • 1985-1992 Cadillac Fleetwood
    • 1992-1999 Oldsmobile 88
    • 1985-1996 Oldsmobile 98
    • 1986-1991 Oldsmobile Delta 88
    • 1996-1998 Oldsmobile LSS
    • 1997-1998 Oldsmobile Regency
    • 1987-1999 Pontiac Bonneville

     

    Package Includes:

    • 2x Front Inner Tie Rod End -EV116
    • 2x Front Outer Tie Rod End -ES2261RL
    • 2x Rear Lower Ball Joint -K5297
    • 2x Front Sway Bar End Link -K90515
    • 2x Rear Sway Bar End Link -K5315
    • 2x Front Sway Bar End Link -K8989

     

    Fault judgment:

    • When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
    • When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
    • If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.

          A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.

     

    Know how to replace the swag bar link:

    • step 1: Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove.
    • step 2: After the tire screws are loosened, jack up the jack.
    • step 3: Remove tires. At this time, completely remove the wheel nut, and then remove the tire from the vehicle.
    • step 4: Find the rocker link to be replaced. The anti-roll bar is usually located at the front of the car and is bolted to the suspension of the car.
    • step 5: Remove the lug nut. After removing the top nut, remove the lower nut. After removing the two nuts, pick up the pry bar and apply pressure on the rocker near the connecting rod.
    • step 6: Make sure that the new joystick link matches the old link. Use a pry bar to apply downward pressure on the rocker, and then install the new link to the position of the old link. Make sure that the installation direction is correct, as the two ends look very similar.
    • step 7: After the link is in place, install the nut and tighten it to the appropriate torque specification.
    • step 8: Put the tires back into the vehicle. Tighten the lug nuts as much as possible, but do not over tighten them. Excessive pressure on the car may knock it off the jack bracket.
    • step 9: Tighten the lug nut. After the vehicle returns to the ground, tighten the lug nut to the appropriate torque specification.If you want to change multiple anti-roll bar links, just repeat these steps on the other side.

    Notes:

    1. Please be sure to check carefully whether the part is suitable for your car model before placing an order
    2. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer

    Item Specifics
    Brand everpartstorecs
    Placement on Vehicle Front Inner Outer Rear Lower
    Manufacturer Part Number 10129565
    Interchange Part Number EV116,ES2261RL,K5297,K90515,K5315,K8989
    Superseded Part Number control arm pressing ball joint car,lower ball joints replacement
    Manufacturer Warranty 1 Year
    Material Alloy Steel
    Vintage Car Part No
    OE/OEM Part Number car tie rod end replacement,inner and outer tie rod end,rods ends
    Type Sway Bar Link
    Finish Coated
    Features Greasable
    Items Included Mounting Hardware
    Mounting Style Bolt-On
    Color Black
    Modified Item No
    Adjustable Yes
    Universal Fitment No
    Cotter Pin Hole Yes
    Custom Bundle No
    Quantity 12 Pieces
    Performance Part No

    Shipping

    1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days.

     

    2.All orders will be shipped from our US warehouses and delivered by USPS,UPS or FedEx.

     

    3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you

     tell us the new address within 12 hours after payment 

    (no delivery to remote areas).

     

    4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time,

     if there are any problems, contact us immediately please.

    Payment

    Any payments accepted by ebay also can be accepted.

    Service

    1. Products can be returned for no reason within 30 days of receipt

     (products to be returned must be in a resalable condition, if they have been used we will not accept the return).

     

    2. If the product does not match the description on the product page, we will exchange or refund the product for free 

    within 30 days.

     

    3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty.

    Note

    If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution.

     

    Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.

    Shop Category
     Store Home
     lift support
     Condenser
     Air Diesel Heater
     Blower Resistor
     Blower Motor
     Heater Core
     Suspension Kits
     Thermostat Housing
     ABS Wheel Speed Sensor
     Window Switch
     Oxygen Sensor
     3Rd Brake Light
     Mass air flow sensor
     AC Compressor
     Cooling Fan
     Towing Mirrors
     Door Handle
     Radiator
     Sensor
     Knock Sensor
     Catalytic Converter
     Window Regulator
     Wheel Spacers
     Alternator
     Headlight Assembly
     Fuel Pump Assembly
     Leveling Lift Kits
     Spoiler Wing
     CV Axle
     Wheel Hub Bearing Knuckle
     Turbocharger
     Windshield Wiper Motor
     Engine Mount
     Head Gasket Set
     complete strut
     4 Pcs Wheel Hub Bearing
     Wheel Hub Bearing
     Tire Anti-skid Chain
     Brake caliper
     Shocks Struts
     Air Suspension
     Brake rotor pad
     Struts & Suspension Kit & Hubs
     Driveshaft
     Starter
     Other

    12 Pcs Front Lower Sway Bar Suspension Kit For 1986-1999 Buick LeSabre 3.8L

    Fit For:

    • 1985-1989 Buick Electra
    • 1986-1999 Buick LeSabre
    • 1991-1996 Buick Park Avenue
    • 1985-1993 Cadillac Commercial Chassis
    • 1985-1993 Cadillac DeVille
    • 1985-1992 Cadillac Fleetwood
    • 1992-1999 Oldsmobile 88
    • 1985-1996 Oldsmobile 98
    • 1986-1991 Oldsmobile Delta 88
    • 1996-1998 Oldsmobile LSS
    • 1997-1998 Oldsmobile Regency
    • 1987-1999 Pontiac Bonneville

     

    Package Includes:

    • 2x Front Inner Tie Rod End -EV116
    • 2x Front Outer Tie Rod End -ES2261RL
    • 2x Rear Lower Ball Joint -K5297
    • 2x Front Sway Bar End Link -K90515
    • 2x Rear Sway Bar End Link -K5315
    • 2x Front Sway Bar End Link -K8989

     

    Fault judgment:

    • When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
    • When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
    • If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.

          A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.

     

    Know how to replace the swag bar link:

    • step 1: Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove.
    • step 2: After the tire screws are loosened, jack up the jack.
    • step 3: Remove tires. At this time, completely remove the wheel nut, and then remove the tire from the vehicle.
    • step 4: Find the rocker link to be replaced. The anti-roll bar is usually located at the front of the car and is bolted to the suspension of the car.
    • step 5: Remove the lug nut. After removing the top nut, remove the lower nut. After removing the two nuts, pick up the pry bar and apply pressure on the rocker near the connecting rod.
    • step 6: Make sure that the new joystick link matches the old link. Use a pry bar to apply downward pressure on the rocker, and then install the new link to the position of the old link. Make sure that the installation direction is correct, as the two ends look very similar.
    • step 7: After the link is in place, install the nut and tighten it to the appropriate torque specification.
    • step 8: Put the tires back into the vehicle. Tighten the lug nuts as much as possible, but do not over tighten them. Excessive pressure on the car may knock it off the jack bracket.
    • step 9: Tighten the lug nut. After the vehicle returns to the ground, tighten the lug nut to the appropriate torque specification.If you want to change multiple anti-roll bar links, just repeat these steps on the other side.

    Notes:

    1. Please be sure to check carefully whether the part is suitable for your car model before placing an order
    2. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer


    1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days.

     

    2.All orders will be shipped from our US warehouses and delivered by USPS,UPS or FedEx.

     

    3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you

     tell us the new address within 12 hours after payment 

    (no delivery to remote areas).

     

    4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time,

     if there are any problems, contact us immediately please.

    Any payments accepted by ebay also can be accepted.

    1. Products can be returned for no reason within 30 days of receipt

     (products to be returned must be in a resalable condition, if they have been used we will not accept the return).

     

    2. If the product does not match the description on the product page, we will exchange or refund the product for free 

    within 30 days.

     

    3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty.

    If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution.

     

    Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.