Technical parameters:
- AC voltage 220 volts/50 Hz;
- Power consumption 2000W, average 1500W;
- Heating temperature: high 750 degrees
- Adjustable working temperature 50-600 degrees;
- Heating output temperature: 50-480
- Air volume: actual: 40-100. fan voltage display value: 12-28
- Automatic sleep timer: 15 minutes without operation
- Adjustable self-propelled splicing speed 0.8-15 metres/minute.
- Full weight 12kg;.
- Package size: 47X31X32
- I. Scope of application:
Spray painting cloth, light box cloth, PVC tarpaulin, yoke mesh canvas, awnings and other coated membrane structure (polyethylene, polypropylene, polyvinyl chloride and other materials that can be fused with heat) splicing of flat surfaces.
- Second, the operation method:
- Will want to splice spray painting screen two splice edge according to 30-40CM lap width up and down layer stacked flat, at both ends from the pressure seam 40CM at the tape or clamps and other fixed products firmly;
- Turn on the power button of the hot splicing machine, turn on the temperature and speed knob respectively, according to the thickness of cloth and material and ground condition, and set the speed and temperature, start to preheat for about 2 minutes;
- Place the machine at the overlapping laminations of the ends of the two spray-painted splices, with the rollers aligned with the edges of the pressed seams;
- Trigger the end handle to the left, insert the hot air nozzle into the upper and lower overlapping seam layers of the airbrush splices and start splicing;
- Hot air nozzle inserted into the upper and lower two splicing screen layer gap, the machine will begin to self-propelled, crimping process, you can gently hold the left handle, control the direction to adjust the run-off, and make the upper splicing edge and the inside of the nozzle can be contacted;
- Splicing to the end of the picture, the end of the handle to the right side of the trigger, so that the hot air nozzle lifted away from the upper and lower splices stacked gap, you can stop the machine, at this point, the job is done.
- Special reminder: after the completion of the work, in order to protect the electric core is not easy to premature aging, must be done to cool down the processing: trigger up the hot air head, temperature adjustment knob digital zero, 5 minutes and then turn off the machine's power button, stop the fan rotation. Encounter is working in special circumstances, such as a sudden power outage, also must first trigger the hot air head, and then return the temperature control knob to zero, and then go to consider the problem of power connection.
-
- Third, automatic hibernation: the machine if no operation in fifteen minutes, will automatically enter a dormant state to save energy, (twelfth minute automatically stop heating, fifteenth minute automatically turn off the power), press the (select) key will restart.
-
- Operation Note: The operator can take some identical fabric samples for the spliced airbrush splice, test the operation according to the above procedure, find out the satisfactory temperature and speed parameters, and then carry out the formal splicing operation. The spliced fabric surface should be kept flat, and the ground at the joints should be kept flat (cement or porcelain tiles or other hard heat-resistant texture is preferred), in order to facilitate the heat splicing and pressing.
-
- IV. Precautions:
- When using this product, always ensure that the working floor is neat and tidy to avoid clutter and cause accidents.
- The working environment should be good, and keep the lighting, do not use the machine in the damp and dark place, do not use wet paper cloth to wipe the machine.
- The working surface should be flat and strong enough to safely support the weight of the machine.
- It is forbidden to use the machine in a way that is not normal; the hot air nozzle should not be directed at the rubber wheel for a long period of time to prevent it from being scalded.
- Make sure that the main power switch is switched off when the work is finished.
- If special circumstances occur during the work, stop using the machine, troubleshooting. Stop the machine after power off.
- After stopping the machine and disconnecting the power, only then can you carry out maintenance and replacement parts, and use standard general-purpose tools for dismantling.
- In order to ensure safe and reliable splicing, especially for the first time users, when to take some splices, according to the operating method of test practice, when skilled before formal use.
- For the sake of safety and to prolong the life, do not use the machine beyond the limit.
-
- V. Maintenance:
- After opening the package, immediately check the machine for any damage or missing components, if so, promptly contact us.
- Please do not discard the original packaging, when handling the machine, take care to re-wrap it, transport should be careful and reduce vibration.
- Regularly brush the hot air vents with a brush to keep them clean;
- Keep the storage site dry and ventilated to prevent rusting;
- Pay attention to keep the suction grille of the fan clean, pay attention to the work and storage site dust removal, to avoid foreign matter blockage, in order to protect the heating system. Hot air blower is not under warranty, please pay attention to the use.
