• Fit For:
    • 2009 - 2014 NISSAN CUBE All Models
    • 2007 - 2011 NISSAN VERSA All Models
    • 2012 NISSAN VERSA Fits 1.8L Hatchback Models Only
     
  • Package Includes:
    • Lower Ball Joints come Pre-Assembled onto the Control Arms
    • 1 x Part # Front Left Lower Control Arm and Ball Joint  - K620566 
    • 1 x Part # Front Right Lower Control Arm and Ball Joint - K620567 
     
  • Fault judgment:

    • 2 Pcs Front Control Arms Suspension Kit For 2007-2011 Nissan Versa 4-Door 1.8L

    Fit For:

    • 2009 - 2014 NISSAN CUBE All Models
    • 2007 - 2011 NISSAN VERSA All Models
    • 2012 NISSAN VERSA Fits 1.8L Hatchback Models Only

     

    Package Includes:

    • Lower Ball Joints come Pre-Assembled onto the Control Arms
    • 1 x Part # Front Left Lower Control Arm and Ball Joint  - K620566 
    • 1 x Part # Front Right Lower Control Arm and Ball Joint - K620567 

     

    Fault judgment:

    • When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
    • When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
    • If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.

    ?

          A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.

     

    Know how to replace the ball joint:

    • step 1: Getting Started

    ?        Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack. At this time, completely remove the wheel nut, and then remove the tire from the vehicle.

    • step 2: Removing the Old Ball Joint
    1. ?Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver.
    2. With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on.
    3. Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint. 
    • step 3: Installing the New Joint
    1. ?Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from.
    2. Bolt the joint into place using the hardware included. 
    3. Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however.
    4. Screw in the new grease fitting and pump grease into the assembly. 

    ?

                                                              

    Notes:

    1. Please be sure to check carefully whether the part is suitable for your car model before placing an order.
    2. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer.

    Item Specifics
    Brand everpartstorecs
    Placement on Vehicle Left Right Front Lower
    Manufacturer Part Number 10264459
    Interchange Part Number K620566 K620567
    Superseded Part Number Front Driver and Passenger Side Replacement
    Vintage Car Part No
    Type Control Arm & Ball Joint Assembly
    Manufacturer Warranty 1 Year
    Material Alloy Steel
    Items Included Mounting Hardware
    Mounting Style Bolt-On
    Universal Fitment No
    Cotter Pin Hole Yes
    Adjustable Yes
    Custom Bundle Yes
    OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly
    OE Spec or Performance/Custom OE Spec
    Control Arm Construction Forged
    Features Greasable
    Kit or Single Part Kit
    Kit Included 2 Pcs
    Finish Coated
    Surface Finish Premium Quality
    Store Speciality Suspension & Steering
    Suspension Grade Standard
    Bundle Description 1x Right 1x Left Lower Front Control Arm and Ball Joint Assembly

    Shipping

    1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days.

     

    2.All orders will be shipped from our US warehouses and delivered by USPS,UPS or FedEx.

     

    3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you

     tell us the new address within 12 hours after payment 

    (no delivery to remote areas).

     

    4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time,

     if there are any problems, contact us immediately please.

    Payment

    Any payments accepted by ebay also can be accepted.

    Service

    1. Products can be returned for no reason within 30 days of receipt

     (products to be returned must be in a resalable condition, if they have been used we will not accept the return).

     

    2. If the product does not match the description on the product page, we will exchange or refund the product for free 

    within 30 days.

     

    3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty.

    Note

    If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution.

     

    Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.

    Shop Category
     Store Home
     lift support
     Condenser
     Air Diesel Heater
     Blower Resistor
     Blower Motor
     Heater Core
     Suspension Kits
     Thermostat Housing
     ABS Wheel Speed Sensor
     Window Switch
     Oxygen Sensor
     3Rd Brake Light
     Mass air flow sensor
     AC Compressor
     Cooling Fan
     Towing Mirrors
     Door Handle
     Radiator
     Sensor
     Knock Sensor
     Catalytic Converter
     Window Regulator
     Wheel Spacers
     Alternator
     Headlight Assembly
     Other

    2 Pcs Front Control Arms Suspension Kit For 2007-2011 Nissan Versa 4-Door 1.8L

    Fit For:

    • 2009 - 2014 NISSAN CUBE All Models
    • 2007 - 2011 NISSAN VERSA All Models
    • 2012 NISSAN VERSA Fits 1.8L Hatchback Models Only

     

    Package Includes:

    • Lower Ball Joints come Pre-Assembled onto the Control Arms
    • 1 x Part # Front Left Lower Control Arm and Ball Joint  - K620566 
    • 1 x Part # Front Right Lower Control Arm and Ball Joint - K620567 

     

    Fault judgment:

    • When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
    • When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
    • If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.

    ?

          A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.

     

    Know how to replace the ball joint:

    • step 1: Getting Started

    ?        Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack. At this time, completely remove the wheel nut, and then remove the tire from the vehicle.

    • step 2: Removing the Old Ball Joint
    1. ?Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver.
    2. With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on.
    3. Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint. 
    • step 3: Installing the New Joint
    1. ?Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from.
    2. Bolt the joint into place using the hardware included. 
    3. Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however.
    4. Screw in the new grease fitting and pump grease into the assembly. 

    ?

                                                              

    Notes:

    1. Please be sure to check carefully whether the part is suitable for your car model before placing an order.
    2. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer.


    1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days.

     

    2.All orders will be shipped from our US warehouses and delivered by USPS,UPS or FedEx.

     

    3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you

     tell us the new address within 12 hours after payment 

    (no delivery to remote areas).

     

    4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time,

     if there are any problems, contact us immediately please.

    Any payments accepted by ebay also can be accepted.

    1. Products can be returned for no reason within 30 days of receipt

     (products to be returned must be in a resalable condition, if they have been used we will not accept the return).

     

    2. If the product does not match the description on the product page, we will exchange or refund the product for free 

    within 30 days.

     

    3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty.

    If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution.

     

    Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.