CORRECT VEHICLE / GENERATION

WHERE THIS PART FITS

This is the large round main headlamp assembly positioned in the front-left bumper/front body lighting area. It sits below the narrow upper wing-mounted combination/DRL lamp.

DO NOT CONFUSE THIS PART WITH THE UPPER BOOMERANG-SHAPED DRL / INDICATOR UNIT.

REFERENCE LOCATION IMAGE — SHOWING THE FRONT LIGHTING AREA. REFERENCE IMAGE ONLY — NOT THE ACTUAL ITEM SUPPLIED.

ACTUAL PRODUCT PHOTOS — ITEM BEING SOLD

WHAT IS THIS PART?

Used Nissan Juke MK1 F15 facelift NSF / front-left main halogen headlamp assembly. The actual identification label shows Nissan/Valeo manufacture, RHD specification and part number 26060BV80A.

The unit forms the Juke's main forward-lighting assembly and is separate from the upper DRL / indicator lamp.

ENGINEERING & REFERENCE NUMBERS

VEHICLE COMPATIBILITY

A — VERIFIED / STRONGLY SUPPORTED

Nissan Juke MK1 F15 Facelift, 2014–2019, requiring the matching front-left / passenger-side RHD halogen main headlamp.

B — PART-NUMBER SUPPORTED

Related facelift applications carrying 26060BV80B / 26060BV90B references. Compare VIN and original lamp specification before ordering.

C — VERIFY BEFORE ORDERING

Nismo, Nismo RS and specification-dependent variants should be checked against the original headlamp number, lighting technology and connectors before purchase.

WHAT DOES IT DO?

The headlamp assembly houses and positions the vehicle's primary forward lighting, providing the controlled beam pattern required for night-time visibility. This particular unit is marked RHD and is intended for the corresponding UK-style right-hand-drive lighting configuration.

MATERIAL & CONSTRUCTION

Moulded composite/plastic rear housing with clear patterned front lens, internal reflector/projector elements, electrical bulb connections, beam-adjustment mechanism and integrated mounting tabs.

COMMON FAILURE / DAMAGE

Used headlamps should always be checked for cloudy or scratched lenses, broken mounting tabs, damaged rear covers, moisture ingress, connector damage, reflector deterioration and adjustment-mechanism faults.

This is a used component. Inspect the actual product photographs carefully. Cosmetic marks consistent with previous use may be present.

POSSIBLE SYMPTOMS OF A FAILED HEADLIGHT ASSEMBLY

Poor beam pattern, moisture inside the housing, inability to adjust beam height, broken mountings, damaged lens or repeated bulb/connection problems.

WHAT IS INCLUDED?

The headlight assembly shown in the actual product photographs. Only items visibly attached in the photographs should be assumed included. Bulbs, modules, brackets or ancillary parts not shown are not automatically included.

ITEM SPECIFICS

⚠ CRITICAL PART-NUMBER CHECK

DO NOT PURCHASE SOLELY FROM VEHICLE MODEL, REGISTRATION OR EBAY'S AUTOMATED COMPATIBILITY.

Nissan can use multiple lighting specifications and revisions within the same model and year. Before ordering compare your original unit with:

26060BV80A • complete part number • revision • RHD/LHD specification • lamp technology • connector • pin arrangement • lens shape • mounting tabs • adjustment mechanism • side/orientation • actual product photographs

FITTING INFORMATION

Difficulty: Intermediate

Estimated workshop time: approximately 0.75–1.5 hours depending on vehicle condition and access.

Typical tools: socket set, ratchet, extensions, screwdrivers/trim tools and suitable headlamp alignment equipment.

Coding: Normally not expected for a conventional halogen housing, but vehicle specification should be checked.

Calibration: HEADLIGHT BEAM ALIGNMENT SHOULD BE CHECKED AFTER INSTALLATION.

GENERAL INSTALLATION SEQUENCE

1. Switch ignition and lighting off.
2. Disconnect battery where appropriate.
3. Gain access to the front lamp mounting points.
4. Disconnect headlamp electrical connectors.
5. Remove retaining fasteners.
6. Remove original headlamp carefully.
7. Compare both assemblies before installation.
8. Install replacement without forcing mounting tabs.
9. Reconnect electrical connections.
10. Test all lamp functions.
11. Check and correctly align headlamp beam.

ILLUSTRATIVE LABOUR COST

Illustrative labour estimates only. Actual workshop charges vary according to garage, vehicle condition, location and additional work required.

THEPARTPILOT offers a professional fitting service at our repair facility, subject to availability. Contact us through eBay before purchase regarding fitting availability.

SHIPPING & PACKAGING

Automotive lighting components are securely packaged to help protect the lens, housing and vulnerable mounting tabs during transport.

Tracked delivery is used where applicable. UK delivery and supported international delivery through eBay's applicable international shipping programme may be available.

ADDRESS NOTICE

Customers must ensure their checkout address is correct before paying. Due to eBay Seller Protection requirements, the delivery address cannot be changed after purchase.

30 DAYS WARRANTY

This listing carries the 30-day seller warranty shown on the source listing. Please retain your order details and contact us through eBay Messages if assistance is required.

VAT & RETURNS

VAT

Where supplied under the applicable second-hand margin scheme, VAT is not separately itemised and there is no separately reclaimable VAT amount shown on the invoice.

RETURNS

Please verify the complete part number, revision, vehicle model, generation, chassis, years, NSF/OSF position, RHD/LHD specification, lighting technology, connector, mounting points and product photographs before installation.

Any refund deduction will comply with applicable law and eBay policy and will reflect an actual reduction in value where legally permitted.

WE BUY CARS FOR CASH

Nationwide collection and same-day payment available, subject to vehicle assessment and agreed purchase terms.

SUSTAINABILITY

Choosing a reusable automotive component helps extend the useful life of an existing part, reduce unnecessary manufacturing demand, reduce automotive waste and support responsible vehicle recycling within the UK automotive industry.