Welcome to our store!
To avoid you buying the wrong parts, DO CHECK the compatible chart above before placing order.
-
Choose a vehicle from the "My Garage" list. Or
-
Enter your vehicle's details with Year / Make / Model / Trim / Engine. Or
-
Contact us: Ask us for double check.
Fitment:
Subaru Baja Sport 2.5L 2004-2006
Subaru Baja Turbo 2.5L 2004-2006
Subaru Legacy Brighton 2.5L 2000
Subaru Legacy GT 2.5L 2000-2004
Subaru Legacy L 2.5L 2000-2004
Subaru Outback Base 2.5L 2000-2004
Subaru Outback H6 3.0L 2002-2004
Subaru Outback L.L. 3.0L 2001-2004
Subaru Outback Limited 2.5L 2000-2004
Subaru Outback VDC 3.0L 2001-2003
Package:
2x Part# Front Stabilizer Sway Bar End Links - K80693
2x Part# Rear Stabilizer Sway Bar End Links - K80426
2x Part# Front Inner Tie Rods Ends - EV473
2x Part# Front Outer Tie Rods Ends - ES3712
2x Part# Front Lower Ball Joints - K9513
Ball Joint Installation Instructions：
Pre-Installation Preparation
- Tools: Torque wrench, socket set, tie rod separator/pickle fork, jack, safety stands, rust inhibitor, thread locker (optional), wire brush, pliers, wheel chocks
- Vehicle: Park on level ground, chock wheels, engage parking brake. Disconnect negative battery terminal for EPS models (per manual).
- Part Check: Match new tie rod end (inner/outer as needed) to vehicle. Ensure ball joint rotates freely, boot is intact, and hardware is complete.
Old Part Removal
- Loosen wheel bolts, lift vehicle with jack, secure with safety stands.
- Remove wheel, extract cotter pin from ball joint nut, then remove the nut.
- Separate tie rod end from steering knuckle with separator (avoid excess impact).
- Mark lock nut position on inner tie rod, then loosen lock nut (hold inner tie rod to prevent rotation) and unscrew old tie rod end.
- Clean inner tie rod connection surface.
New Part Installation Steps
- Clean steering knuckle hole and inner tie rod threads; apply rust inhibitor to knuckle surface.
- Apply thread locker (optional) to inner tie rod, screw on new tie rod end aligned with marked position.
- Hand-tighten lock nut, seat ball joint in steering knuckle, hand-tighten ball joint nut.
- Lower wheel to ground (light load), torque ball joint nut (35-55N·m, follow manual) and install new cotter pin.
- Torque lock nut (40-60N·m, follow manual) while holding inner tie rod.
- Check: Smooth ball joint rotation, undamaged boot, no component interference.
Post-Installation Inspection
- Reinstall wheel, torque bolts (80-120N·m, follow manual).
- Reconnect battery (if disconnected), start vehicle, test full steering lock (≤10s) for smooth operation and no noise.
- Mandatory Four-Wheel Alignment to calibrate toe/camber angles.
- Test drive (20-30km/h then 60-80km/h) for no pulling/vibration; stop if issues arise.
Safety Precautions
- Always use safety stands (never rely on jack).
- Use proper tools to avoid component damage.
- Torque all fasteners to specs (over/under-tightening is dangerous).
- Never reuse cotter pins; replace damaged boots immediately.
- Avoid long/high-speed driving before alignment.
Notice:
Please check the model and important parameters before purchase to avoid unnecessary after-sales problems, if you are not clear, please feel free to contact us, thank you for your cooperation!
| Item Specifics | |
|---|---|
| UPC | Does not apply |
| Brand | VaultPro |
| Manufacturer Part Number | 13687184 |
| Manufacturer Warranty | 1 Year |
| Placement on Vehicle | Front, Rear, Lower |
| Type | Sway Bar Link |
| Universal Fitment | No |
| Items Included | Mounting Hardware |
| Custom Bundle | Yes |
| Interchange Part Number | K80693 K80426 ES3712 EV473 K9513 |
| OE/OEM Part Number | Suspension Steering Tie Rod Ends Linkages Assembly,Ball Joints |
| Superseded Part Number | Front/Rear Driver and Passenger Side Replacement |
| Adjustable | Yes |
| Features | Greasable |
| Surface Finish | Premium Quality |
| Kit Included | 10 Pieces |
| Cross Reference Part Number | 34141AA041, 34141AA042, 34141AC010, 34141AC0109E |
| Cross Part Number | Ball Joint, Sway Bar,Outer Tie Rod, Inner Tie Rod |
| Partlink Number | 2000 2001 2002 2003 2004 2005 2006 |
| Fitment | For Subaru Baja Legacy Outback |
| Bundle Description | Stabilizer Bar Link,Tie Rod End,Ball Joint |
| Finish | Coated |
| Material | Alloy Steel |
| Mounting Style | Bolt-On |
| Cotter Pin Hole | Yes |
About Us:
We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.
Payment:
Any payment can be accepted by ebay.
Shipping:
2-8 working days in transit.
Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of addresses.
Returns:
30-day free return provided.
Contact Us:
Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.
