Welcome to our store!
To avoid you buying the wrong parts, DO CHECK the compatible chart above before placing order.
-
Choose a vehicle from the "My Garage" list. Or
-
Enter your vehicle's details with Year / Make / Model / Trim / Engine. Or
-
Contact us: Ask us for double check.
Fitment:
**With Torsion Bar Suspension Only**
Ford Explorer Eddie 4.0L 1995-2001
Ford Explorer Eddie 5.0L 1996-2001
Ford Explorer Expedition 4.0L 1995
Ford Explorer Limited 4.0L 1995-1998&2000-2001
Ford Explorer Limited 5.0L 1996-1998&2000-2001
Ford Explorer Postal 4.0L 2000-2001
Ford Explorer Sport 4.0L 1995-2000
Ford Explorer Sport Trac Adrenalin 4.0L 2005
Ford Explorer Sport Trac Base 4.0L 2001
Ford Explorer Sport Trac XL 4.0L 2002
Ford Explorer Sport Trac XLS 4.0L 2003-2005
Ford Explorer Sport Trac XLT 4.0L 2003-2005
Ford Explorer XL 4.0L 1995-2001
Ford Explorer XLS 4.0L 1999-2001
Ford Explorer XLS 5.0L 1999-2000
Ford Explorer XLT 4.0L 1995-2001
Ford Explorer XLT 5.0L 1996-2001
Ford Ranger Base 2.3L 2008 -2011
Ford Ranger EV ELECTRIC 1998-2002
Ford Ranger Edge 4.0L 2001-2005
Ford Ranger FX4 4.0L 2006-2009
Ford Ranger Limited 2.3L 2006-2008&2010
Ford Ranger STX 2.3L 2007
Ford Ranger STX 4.0L 2006-2007
Ford Ranger Splash 2.5L 1998
Ford Ranger Splash 4.0L 1998
Ford Ranger Sport 2.3L 2009
Ford Ranger Sport 3.0L 2002
Ford Ranger Sport 4.0L 2006-2011
Ford Ranger Tremor 4.0L 2004
Ford Ranger XL 2.3L 2001-2011
Ford Ranger XL 2.5L 1998-2001
Ford Ranger XL 4.0L 1998-2003&2005-2011
Ford Ranger XLT 2.3L 2001-2011
Ford Ranger XLT 2.5L 1998-2001
Ford Ranger XLT 4.0L 1998-2011
Mazda B2500 SE 2.5L 1998-2001
Mazda B2500 SX 2.5L 1998-2001
Mazda B2500 Troy 2.5L 1999
Mazda B4000 DS 4.0L 2001
Mazda B4000 SE 4.0L 1998-2001
Mazda B4000 Troy 4.0L 2000
Mercury Mountaineer Base 4.0L 1998-2001
Mercury Mountaineer Base 5.0L 1997-2001
Package:
1x Part# Front Left Upper Control Arm Assembly (Driver) - K8708T
1x Part# Front Right Upper Control Arm Assembly (Passenger) - K8710T
2x Part# Front Lower Ball Joints - K8695T
2x Part# Front Inner Tie Rods - EV317
2x Part# Front Outer Tie Rods - ES3461
2x Part# Front Sway Bars - K7275
Control Arm Installation Instructions：
Pre-Installation Preparation
- Tool List: Torque wrench, socket set, ball joint separator, jack, safety stands, rust inhibitor, thread locker (optional)
- Vehicle Condition: Park on a level surface, engage the parking brake and secure the wheels, disconnect the negative battery terminal (power off required for electronic system protection on some models)
- Part Inspection: Verify the new control arm model matches, check for no damage to ball joints and bushings, ensure all accompanying bolts and nuts are complete and free of rust
Old Part Removal
- Lift the vehicle with a jack and secure it with safety stands (never rely solely on the jack)
- Remove the wheel and disconnect the control arm mounting bolts from the steering knuckle and frame/subframe
- Separate the ball joint from the steering knuckle using a ball joint separator and remove the old control arm
New Part Installation Steps
- Clean the mounting surfaces (frame and steering knuckle connection points), remove rust and debris, and apply a thin layer of rust inhibitor
- Position the new control arm in place and hand-tighten the frame/subframe mounting bolts (do not fully torque yet)
- Install the ball joint to the steering knuckle, hand-tighten the ball joint nut to ensure full seating of the ball joint
- Install remaining mounting bolts per vehicle specifications, hand-tighten all bolts initially (to prevent misalignment)
- Lower the jack to place the wheel on the ground, ensuring the vehicle is in a level loaded state
- Torque all bolts sequentially to manufacturer specifications using a torque wrench (Reference Values: Ball joint nut 45-65N·m, frame-end bolts 80-120N·m; always follow vehicle manual for exact values)
- Check control arm clearance: Ball joint should rotate smoothly, bushings must not be twisted, and no interference should occur
Post-Installation Inspection & Debugging
- Install the wheel and torque the wheel hub bolts to specifications
- Reconnect the negative battery terminal, start the vehicle, and check for smooth steering and no abnormal noises
- Four-wheel alignment is recommended (calibrate wheel toe and camber angles after control arm replacement to prevent uneven tire wear)
Safety Precautions
- Use safety stands throughout the process; never perform under-vehicle work without proper support
- Torque all bolts to specified values; over-tightening or under-tightening is prohibited
- Conduct a test drive after installation to confirm no pulling or abnormal noises; stop immediately to inspect if issues arise
Notice:
Please check the model and important parameters before purchase to avoid unnecessary after-sales problems, if you are not clear, please feel free to contact us, thank you for your cooperation!
| Item Specifics | |
|---|---|
| UPC | Does not apply |
| Brand | VaultPro |
| Manufacturer Part Number | 13573169 |
| Manufacturer Warranty | 1 Year |
| Placement on Vehicle | Front, Left, Right, Upper, Lower |
| Type | Control Arm & Ball Joint Assembly |
| Universal Fitment | No |
| Control Arm Construction | Forged |
| Custom Bundle | Yes |
| Interchange Part Number | K7275 K8695T EV317 ES3461 K8708T K8710T |
| OE/OEM Part Number | Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends |
| Superseded Part Number | Front Driver and Passenger Side Replacement |
| Manufacturer Warranty | 1 Year |
| Adjustable | Yes |
| Greasable or Sealed | Greasable |
| Surface Finish | Premium Quality |
| Kit Included | 10 Pieces |
| Cross Reference Part Number | K8695, K8708, 6L2Z5K483AA, 6L5Z5495AA, 1F703224X, F57Z3280AA |
| Cross Part Number | Ball Joint, Control Arm, Inner Tie Rod, Outer Tie Rod, Sway Bar |
| Partlink Number | 2 Front Sway Bar End Links 2 Front Lower Ball Joints |
| Fitment | For Mazda B2500 B3000 B4000 Mercury Mountaineer |
| Fitment 2 | For Ford Explorer Sport Trac Ford Ranger ELECTRIC |
| Fitment 3 | 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 |
| Fitment 4 | 2005 2006 2007 2008 2009 2010 2011 |
| Bundle Description | Control Arm,Stabilizer Bar Link,Ball Joint,Tie Rod End |
| Features | Greasable |
| Finish | Coated |
| Cotter Pin Hole | Yes |
| Material | Alloy Steel |
| Mounting Style | Bolt-On |
About Us:
We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.
Payment:
Any payment can be accepted by ebay.
Shipping:
2-8 working days in transit.
Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of addresses.
Returns:
30-day free return provided.
Contact Us:
Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.
