Listed :-
RAB529 24" Silver : Designed for 24 x 1 3/8" Wheels. Inner Clearance { Axle centre to inner fork crown } 12 1/2" /32cm : For 1 " Threaded Head Fittings : Steerer 5 1/4" / 13 1/2" cm with 1 " /2.5 cm Threading. Unmarked. No Rust
27" Black : Designed for 27 x 1 1/4" Wheels - Inner Clearance { Axle centre to inner fork crown } 14 1/4" /37cm : For 1 " Threaded Head Fittings : Steerer 6 1/2" / 17 cm with 1 1/4" /3cm Threading. Paintwork quite scruffy. These were a guarantee exchange on a bike where the lamp bracket boss on the right hand fork had come adrift due to a faulty weld. This has been filed smooth at some point and semi-touched up, but these would be better with a respray. * Please check steerer length carefully , these will only fit a smaller frame bike *
26" Royal Blue : Designed for 26 x 1 1/4 / 1 3/8 " Wheels Inner Clearance { Axle centre to inner fork crown } 13 3/4" /35cm : For 1 " Threaded Head Fittings : Steerer 5 1/4" / 13cm with 1 " / 2.5 cm Threading. Not sure of the history of these. Have been fitted and used . Paintwork has some overspray of silver spray paint , and has notes marked on in felt pen which should clean off with meths .Lamp Boss on Right hand fork blade - Suitable lamp brackets still available - please ask.
26" Lime Green : Designed for 26 x 1 1/4 / 1 3/8 " Wheels Inner Clearance { Axle centre to inner fork crown } 13 3/4" /35cm : For 1 " Threaded Head Fittings : Steerer 6 " / 15 cm with 2 " / 5 cm of Threading. .New and unused and in good condition.Lamp Boss on Right hand fork blade - Suitable lamp brackets still available - please ask.
26" Blue : Small Frame : Designed for 26 x 1 1/4 / 1 3/8" " Wheels Inner Clearance { Axle centre to inner fork crown } 13 3/4" /35 cm : For 1 " Threaded Head Fittings : Steerer 5 1/4" / 13.5 cm with 1 " / 2.5 cm Threading. Some minor paint chips and flaking and some storage scratches. but I believe these are new and unridden. Mechanically sound
26" Blue : Small Frame 2 : Designed for 26 x 1 1/4 / 1 3/8" " Wheels Inner Clearance { Axle centre to inner fork crown } 13 3/4" /35 cm : For 1 " Threaded Head Fittings : Steerer 5 1/4" / 13.5 cm with 1 " / 2.5 cm Threading. Some minor paint chips and flaking and some storage scratches. These were a guarantee exchange on a new bike because the threading on the lamp boss was faulty. Mechanically sound , but lamp boss is not useable.
24" Chrome ATB * Please note these are NOT Raleigh manufacture. * Sprint 24" universal ATB forks with cantilever brake bosses. Designed to cut down to your required size { Please remember to screw the threaded top race of your head bearing set to a point below the cutting point before cutting , then when removed, the top race will clean up the threading ready for use } Steerer length 10" / 25cm with 6" / 15cm of threading. Designed for use with 1" Threaded head sets { 24 tpi} Inner clearance approx 33cm / 13" from axle hole centre to inner fork crown.
Generally in OK condition, but there is minor tarnishing breaking out at the bottom of each fork leg { See photo} This should not affect performance.
20" Blue traditional. Fork for bikes taking a 20" wheel, but with a more traditional frame set up. Inner clearance {Axle centre to Inner fork crown { 11" /28cm . For 1" Threaded head fittings : Steerer 6 1/4" /16cm , with 1" 2.5cm of threading. These were a guarantee exchange on a new bike which arrived with a biggish area of paint damage on the back of one of the fork legs. { See photo } Forks would benefit from repainting. A few other minor scratches otherwise intact.
20" Lilac : Designed for 20 x 1 /3/8" Wheels - Inner Clearance { Axle centre to inner fork crown } 11 1/4" /28.5cm : For 1 " Threaded Head Fittings : Steerer 6 1/4" / 16cm with 1" /2.5 cm Threading. Reasonable condition, but a couple of more major areas of paint damage. Would benefit from a respray. I believe these were removed from a new bike as a guarantee fault because of the paint damage. so have been fitted but not ridden. .
Raleigh 14 Blue : Used condition - I believe these were recycled from a Raleigh Fourteen which was being scrapped because of frame damage. Mechanically appear to be fine , but would ideally benefit from a respray if appearance is important. Has the cutouts to accommodate the quick release handlebar bracket Inner clearance axle centre to inner fork crown 21cm / 8" For 1" Threaded head fittings Steerer 10 3/4" / 27.5cm with 3/4" / 2cm of threading. Only one " R" logos present but faded.
Raleigh 14 Blue { Set 2 } : Used condition - I believe these were recycled from a Raleigh Fourteen which was being scrapped because of frame damage. Mechanically appear to be fine , but would ideally benefit from a respray if appearance is important. Has the cutouts to accommodate the quick release handlebar bracket Inner clearance axle centre to inner fork crown 21cm / 8" For 1" Threaded head fittings Steerer 10 3/4" / 27.5cm with 3/4" / 2cm of threading. Both " R" logos present
Head fitting sets available to suit all forks at time of listing . Please ask.
Thank you for your interest