Heavy-duty automatic commercial hand dryer with a brushed 304 stainless-steel casing, high-speed airflow and touch-free infrared activation.
The anydry 2800 is designed for wall mounting in commercial and domestic washrooms. It produces concentrated airflow through its round outlet and automatically controls the heating element according to the surrounding room temperature.
IMPORTANT MODEL AND FINISH INFORMATION
This is the anydry 2800 in the brushed stainless-steel finish.
It should not be confused with:
• The polished stainless-steel version
• The black version
• The anydry 2800B advertising-panel model
• Smaller anydry 2630 or 2803 models
• Higher-powered 2005-series hand dryers
Key Features
• anydry 2800 automatic electric hand dryer
• Brushed stainless-steel finish
• Heavy-duty 304 stainless-steel outer casing
• Touch-free infrared sensor activation
• Approximately 1400W maximum power
• 220-240V 50/60Hz operation
• Stated 10-15 second drying time
• Approximately 70m/s concentrated airflow
• Smart temperature-dependent heating system
• Automatically uses warm air in cooler room temperatures
• Reduces heating use when the room is warmer
• Round concentrated air outlet
• Power and operation indicator lights
• Sponge air filter
• Overheat and overcurrent protection
• Approximately 45-second automatic safety shut-off
• Wall-mounted surface installation
• Fixed mains cable with UK three-pin plug
• Approximately 1.7m power cable
• Suitable for busy commercial washrooms
Automatic Touch-Free Operation
The dryer activates when hands are placed beneath the infrared sensor.
No physical button needs to be pressed, helping reduce contact between different users and making it suitable for public or shared washrooms.
The airflow should stop automatically shortly after the hands are removed from the sensing area.
If hands are held continuously beneath the sensor, the dryer includes an automatic safety cut-out after approximately 45 seconds.
1400W High-Speed Drying
The dryer has a maximum stated power of approximately 1400W and is designed to dry hands in around 10-15 seconds under suitable conditions.
The round outlet concentrates the airflow rather than spreading it across a wide opening. The manufacturer states an air speed of approximately 70 metres per second.
Actual drying time will vary according to:
• How wet the hands are
• The position of the hands beneath the outlet
• Room temperature
• Supply voltage
• Air-filter condition
• Installation height
• Ambient humidity
Smart Automatic Heating
The built-in temperature-control system automatically changes the use of the heating element according to the surrounding temperature.
When the room temperature is below approximately 25°C, the dryer produces warmed airflow.
When the surrounding temperature is above approximately 25°C, the heating element is reduced or switched off and the unit primarily uses normal-temperature airflow.
This is automatic rather than a manually selected hot and cold switch.
The outgoing air is intended to feel warm rather than extremely hot. The exact temperature will depend on room conditions and how long the dryer has been operating.
Brushed 304 Stainless-Steel Casing
The outer casing is made from corrosion-resistant 304 stainless steel with a brushed finish.
The metal housing is more robust than a lightweight plastic casing and is suitable for locations with frequent daily use, including:
• Restaurants and cafés
• Offices
• Hotels
• Schools and colleges
• Shops
• Workshops
• Community buildings
• Commercial toilets
• Staff washrooms
• Public facilities
The brushed finish can still show fingerprints, water marks and cleaning residue. Clean it using a soft cloth and a suitable stainless-steel cleaner.
Wall-Mounted Installation
This is a fixed wall-mounted hand dryer and is not a portable freestanding appliance.
The wall must be sufficiently strong and suitable for supporting the approximately 4.5kg unit. Fixings must be appropriate for the wall construction.
Ensure adequate clearance beneath the air outlet so users can place their hands comfortably beneath the sensor.
Do not mount it where the sensor can be triggered continuously by a basin, shelf, reflective surface or another object positioned directly underneath.
Power Connection
The dryer is supplied with a fixed power cable and UK three-pin mains plug for connection to a suitable socket.
The cable is approximately 1.7m long.
Where a permanent concealed electrical connection is required, installation or alteration should be completed by a suitably qualified electrician. The existing cable should not simply be cut off or modified without proper electrical assessment.
Installation in a washroom or other area close to water must comply with the applicable electrical and building requirements for the location.
Do not use an unsuitable extension cable or place the plug, socket or electrical connection where it can be exposed to water.
Automatic Sensor
The infrared sensor is located beneath the unit near the airflow outlet.
For reliable activation:
• Place hands beneath the sensor rather than against the front casing
• Keep the sensor window clean
• Do not cover the sensor
• Avoid fitting the dryer directly above reflective surfaces
• Ensure the unit is mounted at an appropriate height
A dirty or obstructed sensor can cause delayed activation, continuous operation or failure to start.
Sponge Air Filter
The dryer includes a sponge-type air filter to reduce larger particles entering the airflow system.
The filter should be inspected and cleaned periodically, particularly in dusty commercial locations.
A blocked filter can reduce airflow, extend drying time and cause the unit to operate at a higher temperature.
Disconnect the dryer from the electricity supply before cleaning, inspecting or removing any cover.
Noise Level
The stated operating sound level is approximately 76dB.
This is a high-speed commercial hand dryer and will be clearly audible while operating. It should not be described as silent.
The perceived noise level will vary according to room size, tiled surfaces, installation method and wall construction.
Safety Protection
The unit includes:
• Automatic sensor shut-off
• Approximately 45-second continuous-use cut-out
• Overheat protection
• Overcurrent protection
• Internal electrical protection for the control board
These systems are safety features and should not be used as a substitute for correct installation and maintenance.
Do not cover the air inlet or outlet. Do not insert objects into the dryer and do not allow liquids to enter the casing.
Cleaning and Maintenance
Disconnect the electrical supply before cleaning.
Wipe the external stainless-steel surface with a soft damp cloth and dry it afterwards to prevent water marks.
Do not use:
• Abrasive pads
• Wire wool
• Bleach
• Strong acids
• Caustic cleaners
• Solvent cleaners
• Pressure washers
• Excessive water
The sensor window should be kept clean and free from soap, dust and water residue.
The air inlet and filter should be checked regularly, particularly when the dryer is installed in a high-traffic or dusty environment.
Technical Details
Brand: anydry
Model: 2800
Product type: Commercial automatic hand dryer
Finish: Brushed stainless steel
Casing material: 304 stainless steel
Casing thickness: Approximately 1.2mm
Operation: Automatic infrared sensor
Voltage: 220-240V AC
Frequency: 50/60Hz
Maximum power: Approximately 1400W
Unheated motor power: Approximately 550W
Air speed: Approximately 70m/s
Drying time: Approximately 10-15 seconds
Sound level: Approximately 76dB
Heating control: Automatic according to ambient temperature
Safety shut-off: Approximately 45 seconds
Motor type: Carbon-brush universal motor
Filter: Sponge filter
Installation: Wall-mounted surface installation
Power lead: Fixed approximately 1.7m cable
Plug: UK three-pin plug
Dimensions: Approximately 320 x 295 x 170mm
Weight: Approximately 4.5kg
Approximate Dimensions
Height: 32cm
Width: 29.5cm
Depth: 17cm
Weight: 4.5kg
Measure the proposed installation space before ordering and allow additional clearance for airflow, hands and the power cable.
Package Contents
• anydry 2800 automatic hand dryer
• UK mains power cable and plug
• Wall-mounting components
• Installation and operating instructions
Please check the listing photographs for the exact contents supplied.
Important Buying Information
This is an automatic commercial hand dryer and not a domestic hair dryer, blower or room heater.
It is intended to be mounted securely to a suitable wall.
The heating system is controlled automatically. The user cannot normally select a permanently hot or cold setting from an external switch.
The dryer may produce unheated or mildly warm air when the room temperature is already high. This is normal operation and does not necessarily indicate a heater fault.
FAQ
Which exact model is this?
This is the anydry 2800 commercial automatic hand dryer.
Which finish is supplied?
This is the brushed stainless-steel version.
Is it polished chrome?
No. It has a brushed satin-style stainless-steel finish rather than a mirror-polished finish.
Is this the 2800B model with an advertising panel?
No. This is the standard 2800 model without the upper advertising display panel.
Is it automatic?
Yes. It uses an infrared sensor to start when hands are placed beneath the unit.
Does it have a push button?
No. Normal operation is touch-free through the automatic sensor.
What is the power rating?
The maximum stated power is approximately 1400W.
What voltage does it require?
It is designed for a 220-240V 50/60Hz electricity supply.
How quickly does it dry hands?
The manufacturer states approximately 10-15 seconds under suitable conditions.
What is the stated air speed?
Approximately 70 metres per second.
Is the air heated?
Yes. The heating system operates automatically according to the room temperature.
Can I manually switch between hot and cold air?
No external manual heat-selection switch is stated. The dryer controls the heating automatically.
Why might the air not feel hot?
When the room temperature is above approximately 25°C, the unit may reduce or switch off the heating element and use normal-temperature airflow.
Does this mean the heater is faulty?
Not necessarily. Temperature-dependent heating is part of the normal Smart Warm operation.
Is the casing plastic?
No. The outer casing is made from stainless steel.
What grade of stainless steel is used?
The manufacturer specifies 304 stainless steel.
Is it suitable for a busy commercial toilet?
Yes. It is marketed as a heavy-duty commercial hand dryer for frequent use.
Does it have a UK plug?
Yes. The UK version is supplied with a three-pin plug and fixed power cable.
How long is the power cable?
Approximately 1.7m.
Can it be hardwired?
A qualified electrician may be able to adapt the installation where appropriate. Do not remove or alter the cable without competent electrical assessment.
Can I install it myself?
Mechanical installation requires a suitable wall and secure fixings. Electrical installation or alteration in a washroom should be carried out by a suitably qualified person.
Does it include wall fixings?
Standard mounting components are normally supplied. Check the listing photographs for the exact contents.
How heavy is it?
Approximately 4.5kg.
What are the dimensions?
Approximately 32cm high, 29.5cm wide and 17cm deep.
Does it have a filter?
Yes. The model uses a sponge-type air filter.
Does the filter need cleaning?
Yes. Periodic inspection and cleaning help maintain airflow and drying performance.
How loud is it?
The stated noise level is approximately 76dB. It is a high-speed commercial appliance and will be clearly audible while operating.
Does it switch off automatically?
Yes. It stops when the hands are removed and also includes an approximately 45-second continuous-use safety cut-out.
Why might it run continuously?
Check that the sensor is clean and that no basin, shelf, reflective surface or other object is permanently triggering it.
Can it be mounted directly above a sink?
It can be installed in a washroom, but the mounting position must avoid water exposure, accidental sensor activation and unsuitable electrical zones.
Is it waterproof?
Do not treat the complete appliance as waterproof. It must not be sprayed, submerged or exposed to direct running water.
Can it be used as a hair dryer?
No. It is designed only for drying hands beneath the fixed wall-mounted outlet.
Can it be used as a room heater?
No. It is not designed to heat a room.
Discount available for collection – 07405 422 940