- ☑️ [AUTOMOTIVE FIRST. WORKS EVERYWHERE ELSE TOO] – Engineered for collision repair, spray booth painting, and auto refinishing. Equally effective for interior wall painting, construction masking, window protection, and furniture coverage. Tear-resistant, waterproof, zero adhesive residue on all surfaces.
- ☑️ [CORONA TREATED – PAINT LOCKS ONTO FILM, NOT THE FLOOR]– JMI BASIC white masking film uses corona treatment to bond overspray paint directly to the film surface. No dripping. No flaking during removal. No paint landing back on your fresh finish. The standard for professional auto body shops worldwide.
- ☑️ [ANTI-FLAKE & CLEAN FINISH] - Unlike cheap plastic, dried paint sticks to our film like a magnet. This prevents dried paint dust from falling onto your fresh coat when removing the film.
- ☑️ [ELECTROSTATIC CLING] – GRIPS PANELS ON CONTACT, NO EXTRA TAPE – Electrostatically charged film sticks to car doors, hoods, fenders, and bumpers the moment it touches the surface. Stays flat through an entire spray session. Zero gaps. Zero bleed-through. Zero mid-job adjustments.
- ☑️ [HEAT RESISTANT TAPE UP TO 80°C / 176°F FOR 60 MINUTES – NO RESIDUE] – Pre-attached yellow crepe tape withstands spray booth temperatures for up to 60 minutes without softening, bleeding, or leaving adhesive residue. Peels off cleanly in one smooth motion – no sticky traces on panels, trim, or glass. Rubber-based adhesive ensures strong hold during the job and clean release after.
- ☑️[FLEXIBLE FILM THAT CONFORMS TO EVERY CURVE] – Unlike stiff plastic sheeting that gaps on body lines, JMI BASIC film is soft and pliable enough to follow door edges, bumper curves, fender arches, and mirror housings without lifting or creasing. One smooth, gap-free seal across every panel shape.
- ☑️[TAPE ALREADY ATTACHED 2 in 1 – FULL PANEL COVERED IN 60 SECONDS] – Yellow crepe masking tape is pre-bonded to the film edge. No fumbling with separate rolls. Position, unfold, done. One person can mask an entire vehicle in minutes. Works with HVLP spray guns, rattle cans, and paint robots.
JMI BASIC white masking film solves all three.
① Corona Treatment – Paint stays on the film
The surface is restructured at a molecular level so spray paint bonds directly to the film. No sliding. No dripping. No flaking on removal.
② Flexible Film – Follows every curve
Soft, pliable material conforms to door edges, bumper curves, fender arches, and mirror housings without lifting or gapping. One person. One pass. Complete seal.
③ Electrostatic Cling – Sticks on contact
No extra tape needed to hold the film to panels. The electrostatic charge grips the surface automatically, even on vertical and overhead areas.
④ Professional Grade Tape – Built for the Booth
Pre-attached yellow crepe tape is engineered to perform where standard tapes fail.
Tape Specifications:
- Tape Thickness: 0.135mm
- Adhesive Type: Rubber-based
- Adhesion Strength: 4 N/25mm width
- Tensile Strength: 90 N/25mm width
- Elongation: 9%
- Heat Resistance: 80°C / 176°F – 60 minutes
Holds firm through full spray booth heat cycles. Peels off in one clean motion. Zero adhesive residue on panels, trim, glass, or painted surfaces.
What you get:
- Corona treated – automotive professional grade
- Flexible film conforms to curved body panels
- Electrostatic cling grips all surfaces automatically
- Heat resistant tape 80°C / 176°F for 60 minutes
- Rubber-based adhesive – strong hold, clean release
- Zero adhesive residue on all surfaces
- Compatible with solvent and waterborne automotive paints
- Works for interior painting, construction, and DIY
- Tear-resistant and waterproof plastic film
Available in 18", 26", 35", 59", 94" size pack
For professionals and DIYers who won't redo the same job twice.
⚠️ PLEASE NOTE:
Test the tape first on an inconspicuous surface before use.
If the attachment is worn, moist, or corroded, the area may float. Please use the film after removing the area.
Unroll to the desired length and cut with scissors before unfolding plastic.
Make sure tape is fully unfolded for maximum coverage.