6 Gauge Set 85mm Speedometer 0-200KM/H Gauge Tacho & 52mm Fuel Level Water Temp Oil pressure Volt For Car Boat

Features:
 

• -Suitable for all vehicles and off-road vehicles
  
• -The signal comes directly from the satellite signal receiver(GPS Antenna), don't need other speed sensor.
  
• -The gauge has the advantages of high precision, quick location confirmation and short start up time.
  
• -IP67 waterproof and dustproof grade
  
• -Reverse polarity protection and anti-fogging performance
  
• -No Stationery Drift
  
• -Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.

Specifications:
 

• -Fixing dimension: 85mm(3-3/8")
  
• -Indicating Range: 0-200Km/H
  
• -Working Voltage: 12V/24V
  
• -Range: 0-200 KM
  
• -Signal: Pulse signal
• -OverSpeed Buzzer Alarm
  
• -Indication light: LEFT, HIGH BEAM, RIGHT
  
• -Backlight: Red and Yellow available
  
• -Working temperatures: - 40 to 85°C
  
• -Operation mode: LCD display, stepper motor

Technical Data:
 

• Name: Tachometer
  
• Materials: stainless steel+nickel-plated plastic
  
• Operating Voltage: 12V/24V
  
• Indicating Range: 0-10000RPM
  
• Input Signal: Pulse Signal from engine speed sensor, engine, alternator, ignition coil, crankshaft sensor, etc.
  
• Adjustable speed ratio: 0.5-250.0
  
• Protection Class: IP67, can work underwater 1 meter position

Function Select (Pulse, Hour, Buzz)
 

• Press and hold on the button at the back, then turn on the power supply.
  
• The LCD will show PULSE, HOUR, BUZZ, etc.
  
• You can select the function to be set after release button.
• 1.“PULSE” (change RPM Ratio)
       
• After selecting “PULSE”, the LCD will show for example “P 3” (3 means 3pulses per round) after 3 seconds. Press the button to change the flashing digit in the LCD
• You can select “PULSE” again to confirm the setting is done.
  
• How to confirm RPM Ratio?
  
• a. If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine.
  
• b. If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles.
• 2.“HOUR”(change total hour meter)   
  
• After selecting “HOUR”, the LCD will show for example “5000” (5000 HOUR) , press the button to change the flashing digit from 0 to 99999 to set the target value.
• 3.“BUZZ”(change overspeed buzzer alarm threshold value)    
  
• After selecting “BUZZ”, the LCD will show for example “B 3000” (buzzer will be on when speed over 3000RPM), press the button to change the flashing digit from 0 to 8000 to set target overs RPM buzzer alarm threshold value. 
  
• Please noted: After setting, you should disconnect both Power+ and GND, and then reconnect the
  two cable, then it will save the setting. If you just cut Power +, then it’ll not work properly.

• 1X 85MM Speedometer gauge with pulse signal
• 1X 85MM Tachometer
• 1X 52MM Fuel Level Gauge
• 1X 52MM Water Temperature gauge
• 1X 52MM Oil Pressure Gauge
• 1X 52MM Voltage
• 1X Water temp sensor
• 1X Oil pressure sensor
• 1X Fuel level sensor 240-33ohms
• Instructions