Application：
1.Precious metal alloys; gold, silver, platinum and palladium
2.Titanium and stainless steel.
3.With some limitations, aluminum, tin and most brass alloys
4.Alloys with different attributes that are incompatible in normal welding
5.Alloys that would oxidize during welding and thus require an inert(Argon) atmosphere
Sparkle welder which use for jeweler:
6.Precisely position parts by tacking with the spot welder
7.Welding of necklaces with a diameter 0.3mm or larger(smaller diameter may melt)
8.Repair metal joints or breaks without removing set stones or pearls
9.Repair heat sensitive metals or metal alloys
10.Repair surface or entry point of a molding of the same alloy

With the inert argon atmosphere, welding can be done without requiring fluxing. The soldering point is smooth and does not require scaling or scale removal.

Installation and commissioning：
1.Connecting electrode, black wire to black connection (ground/cathode), red wire to red connection (positive /anode).
2. Connect argon gas through the argon gas pressure reducing valve; adjust the gas pressure reading to the minimum
3. Tungsten needle can be sharpened by grinding on the grinding wheel, or with the use of a Fordham flex shaft or dremal tool and an abrasive disk. Note that you should not use a wheel previously used to grind iron/steel as this will contaminate the needle and cause an uneven spark and/or weld results.
4. When installing the tungsten needle, please insure that the needle is approximately 5mm out from the welding head. The diameter of needle should be 0.1mm.

Steps:
1. Plug the device into the wall socket and turn it on
2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material.
3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow.
4. Clamp the object to be welded with

Application：
1.Precious metal alloys; gold, silver, platinum and palladium
2.Titanium and stainless steel.
3.With some limitations, aluminum, tin and most brass alloys
4.Alloys with different attributes that are incompatible in normal welding
5.Alloys that would oxidize during welding and thus require an inert(Argon) atmosphere
Sparkle welder which use for jeweler:
6.Precisely position parts by tacking with the spot welder
7.Welding of necklaces with a diameter 0.3mm or larger(smaller diameter may melt)
8.Repair metal joints or breaks without removing set stones or pearls
9.Repair heat sensitive metals or metal alloys
10.Repair surface or entry point of a molding of the same alloy

With the inert argon atmosphere, welding can be done without requiring fluxing. The soldering point is smooth and does not require scaling or scale removal.

Installation and commissioning：
1.Connecting electrode, black wire to black connection (ground/cathode), red wire to red connection (positive /anode).
2. Connect argon gas through the argon gas pressure reducing valve; adjust the gas pressure reading to the minimum
3. Tungsten needle can be sharpened by grinding on the grinding wheel, or with the use of a Fordham flex shaft or dremal tool and an abrasive disk. Note that you should not use a wheel previously used to grind iron/steel as this will contaminate the needle and cause an uneven spark and/or weld results.
4. When installing the tungsten needle, please insure that the needle is approximately 5mm out from the welding head. The diameter of needle should be 0.1mm.

Steps:
1. Plug the device into the wall socket and turn it on
2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material.
3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow.
4. Clamp the object to be welded with

NOTE:
1.Your valid phone number is  very necessary for the shipping, otherwise we can't guarantee that the package would safely arrives.
2. Any Customs tax applied to this package should be covered by  buyers.
3.As has been stated on the eBay item description, Import duties, taxes and  charges are not included in the item price and shipping charges.These charges be at the buyer responsibility. meanwhile the customs tax depend  on the buyer local customs office.