· Packungsinhalt /Package contents:
Deutsch: Dieses Angebot enthält:
3 Stück Nema34 34HS9840 4A 100MM Schrittmotor
3 Stück Schrittmotortreiber DM860 PEAK 7.8A
3 Stück Schaltnetzteil S-350-60 (350W 60V) Netzteil
1 Stück Breakout Board & Kable DB25
English: This item includes:
3PC Nema34 Stepper Motor 34HS9840 4A
3PC Stepper Motor Driver DM860 Peak 7.8A
3PC Power Supply 350W 60V
1PC Breakout Board&Cable
There are three wiring configurations for 8-wire motors: single-pole, bipolar series connection, and bipolar parallel connection. The parameters for each wiring configuration are as follows:
Es gibt drei Verdrahtungskonfigurationen für 8-adrige Motoren: einpolige, bipolare Reihenschaltung und bipolare Parallelschaltung. Die Parameter für jede Verdrahtungskonfiguration sind wie folgt:
DE | EN | CONNECTION MODE UNIPOLAR | CONNECTION MODE SERIES BIPOAR | CONNECTION MODE PARALLEL BIPOLAR |
Schrittwinkel | Step Angle | 1,8 ± 5% °/ Step | ||
Spannung | Rated Voltage | 3,2V | 4,48V | 2,24V |
Nennstrom | Rated Current | 4 A /Phase | 2,8 A /Phase | 5,6 A /Phase |
Widerstand pro Phase | Phase Resistance | 0,8 ± 10% ohm/Phase | 1,6 ± 10% ohm/Phase | 0,4 ± 10% ohm/Phase |
Induktanz pro Phase | Phase inductance | 3,5± 20% mH/Phase | 14± 20% mH/Phase | 3,5± 20% mH/Phase |
Drehmoment | Holding Torque | 7,7 N.m Min(1090 OZ.IN) | 10,78 N.m Min(1526 OZ.IN) | 10,78 N.m Min(1526 OZ.IN) |
Rastmoment | Detent Torque | 9,5 N.cm Max | ||
Drehmoment | Rotor Torque | 1700 g- cm² | ||
Anzahl der Drahtleitungen | Number of Wires | 8 | ||
Wellendurchmesser | Shaft Diameter | Dual Flat Shaft=Φ14 ± 0,012 mm | ||
Motorlänge | Motor Length | 100 mm | ||
Gewicht | Motor Weight | 3,18 kg | ||
Input Voltage/ Eingangsspannung | 24-80V DC, 60 V (typisch) |
Microstep Setting/ Unterteilungsbereich | 400-51200 ppr |
Output Current/ Ausgangsstrom | 2.8A-7.8A |
Input Pulse Frequency/ Impulsantwort Frequenz | 200 kHz (.) |
Insulation Resistance / Isolationswiderstand | ≥500MΩ |
Storage Environment | -40 ℃ - +70 ℃ |
Humidity | Not condensation, no water droplets |
Weight | 500g |
Using Environment | -10 ℃– 45 ℃, avoid dust and corrosive gas |
Detailed information
Spannung | DC Voltage | 60V |
Spannungstoleranz | Voltage Tolerance | +/-1% |
Nennstrom | Rated Current | 5,85 A |
Strombereich | Current Range | 0-5,85A |
Spannungsspannung | Ripple &Noise | (Max): 240mVp-p |
Line Regulation | Line Regulation | +/- 0,5% |
Load Regulation | Load Regulation | +/- 0,5% |
Nennleistung | Rated Power | 350 W |
Nennleistung | Rated Power | 86% |
Wechselstrom | AC Current | 6,5A/115V 4,0A/230V |
Anlaufzeit | Setup Rise, Hold Time | 200ms, 100ms, 20ms |
Vibration | Vibration | 10-500Hz, 2G 10min/11 Zyklus, 60min, je Achse |
Stehspannung I/P-O/P | Withstand Voltage I/P-O/P | 3KVACI/P-FG: 1.5KVACI/P-FG:0.5KVAC |
Isolationswiderstand | Isolated Resitor | I/P-O/P, I/P-FG:500VDC/100M W |
Arbeitstemperatur / Feuchtigkeit | Working Temp. Humidity | -20°C - +85°C, 10%-95%RH |
Abmessung | Dimension | 215mmx115mmx50mm |
Gewicht | Weight | 0,9kg |
Sicherheitsstandart | Saftey Standart | UL1950 |
EMC | EMC | FCCpart1.5J class A |
1. Provides twelve OC (collector-open circuit) outputs and five optically isolated common-ground signal inputs.
2. Dual power supply design facilitates connection to an isolated power source, providing a non-common-ground independent power supply for the optically isolated circuit, achieving complete isolation between the front and rear stages. The isolation terminal operates at 5–12 VDC (other voltages require customisation).
3. Can be powered by a single +5 V supply, with no power required at the output terminals.
4. All output signals from the computer parallel port are shaped by Schmitt triggers to enhance the anti-interference performance of digital signal transmission.
5. Can be used with parallel port control software for industrial control applications.
6. Supports parallel port-based CNC control software such as KCAM4, MACH, and EMC, supporting up to 6 axes.
7. Can be used with all pulse and direction signal stepper and servo drives to control lathes and milling machines for CNC operation.
8. The input terminals can be connected to mechanical switches, slot-type optocouplers, proximity switches, tool setters, etc.
9. The signals on the interface board's P1-P17 ports correspond one-to-one with the computer parallel port's pins 1-17, while pins 18-25 of the parallel port are power ground.
10. Dimensions: 90mm x 70mm, mounting holes: 80mm x 60mm.
Connection | Connect 6 Drivers, control 6 Motors at the same time |
DB25 Output Pin | P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17 |
DB25 Input Pin | P10,P11,P12,P13,P15 |
DB25 GND Pin | P18 - P25 |
P2 = | X axis Pulse |
P3 = | X axis Direction |
P4 = | Y axis Pulse |
P5 = | Y axis Direction |
P6 = | Z axis Pulse |
P7 = | Z axis Direction |
P8 = | A axis Pulse |
P9 = | A axis Direction |
P14 = | B axis Pulse |
P1 = | B axis Direction |
P16 = | C axis Pulse |
P17= | C axis Direction |
Input pin: P10 ,P11, P12, P13, P15 | Set them for Emergency Stop and X Y Z Limit switch |
· Other information
Up to now, we are looking for qualified dealers with competitive prices and favorable discounts in the EU, in order to establish a mutually beneficial long-term relationship. We will try our best to support our dealers and business partners to develop more.
· OEM Service:
Deutsch: Wir können unsere Produkte auf Kundenwunsch anfertigen: Motorlänge, Kabellänge, Wellenmodus, Anschlussdrähte, etc.
English: We could manufacture products according to customer's requirement: Motor Length, Cable Length, Shaft Mode, Lead Wire Mode, and so on.
English: If you need more pictures, descriptions, manual, please contact me!
· Zalung/Payment
Deutsch:
- Wir akzeptieren nur die Zahlung per Paypal.
- Die Artikel ist innerhalb von 4 Tagen zu bezahlen, anderfalls werden Sie einen Fall von eBay wegen nicht bezahlter Artikel erhalten.
- Bitte beachten Sie:
a)Alle weiteren möglichen Einfuhrzölle, Steuern und andere Gebühren sind nicht im Artikelpreis oder in den Versandkosten enthalten. Diese Gebühren sind die Verantwortlichkeit der Käufer.
b)Bitte bestätigen Sie mit Ihrer ländischen Zoll vor dem Kauf, wieviel diese Kosten betragen.
- Alle Preise verstehen sich inkl. 16% Mehrwertsteuer!
English:
- We only accept payment via Paypal.
- The item is payable within 4 days, otherwise you will receive a case from eBay for unpaid items.
- Please note:
a) All other possible import duties, taxes and other charges are not included in the item price or shipping charges. These charges are the responsibility of the buyer.
b) Please confirm with your customs before buying how much these costs are.
· Versand / Delivery
Deutsch:
- Bitte beachten Sie die Versandmethoden und Versandkosten.
- Bei jeglichen Fragen zum Produkt oder zum Versand, kontaktieren Sie uns bitte.
- Versand via UPS und DHL
- Alle gezeigten Produkte sind verfügbar und können sofort verschickt werden.
- Der Käufer trägt bei Bestellungen ins EU-Ausland (z.B Schweiz, Norwegen ect.) die Kosten für Zoll, Einfuhr und ggf. Steuer (Frankatur DDU)
English:
- Please check the shipping methods and shipping costs.
- If there are any questions according to the product or shipping, please contact us.
- All products are available and can be shipped out right after payment.
- Shipping via UPS und DHL
- The buyer has to pay the cots of custom clearance, import and possibly taxes if the order has to be shipped to a non EU-country (e.g. Switzerland, Norway...) (franking DDU)
· Probleme / Rückmeldungen / Rückerstattungen
Deutsch:
- Bitte kontaktieren Sie uns also, bevor Sie eine negative Bewertung hinterlassen.
- Bitte geben Sie uns die Möglichkeit, eventuelle Probleme die Sie mit unseren Produkten oder dem Versand haben zu lösen.
English:
- Please contact us before leaving a negative rating
- Please give us the opportunity to solve any problems you may have with our products or shipping.