30W Electric Vacuum Solder Sucker Pump Desoldering Gun Welding Iron Tools Blue
Popular
Product Introduction
Features:
1. Using 110/220V 50hz power supply, power 30W;
2. Turn on the power and preheat for 3-5 minutes;
3. Press the piston handle, and align the tin suction nozzle with the welding part; after the tank is melted, press the control button, and the welding seam is sucked into the cylinder;
4. The tank suction unit is equipped with two suction nozzles of different diameters, depending on the thickness of the lead parts;
5. When soldering, the operation is the same as that of a soldering iron; it can be used for both soldering and tin absorption
6. When disassembling the cylinder, press down the top of the cylinder in the direction of the arrow, and pull the cylinder and handle at the same time, the cylinder can be separated; when disassembling the suction nozzle, turn the suction nozzle counterclockwise and remove it;
1. Using 110/220V 50hz power supply, power 30W;
2. Turn on the power and preheat for 3-5 minutes;
3. Press the piston handle, and align the tin suction nozzle with the welding part; after the tank is melted, press the control button, and the welding seam is sucked into the cylinder;
4. The tank suction unit is equipped with two suction nozzles of different diameters, depending on the thickness of the lead parts;
5. When soldering, the operation is the same as that of a soldering iron; it can be used for both soldering and tin absorption
6. When disassembling the cylinder, press down the top of the cylinder in the direction of the arrow, and pull the cylinder and handle at the same time, the cylinder can be separated; when disassembling the suction nozzle, turn the suction nozzle counterclockwise and remove it;
Notes:
1. Ensure that the voltage is consistent, the voltage is too high or too low is not conducive to use;
2. Before use, tighten the cylinder and suction nozzle to prevent leakage. Otherwise it will affect the suction.
3. Frequently clean the welding impurities in the suction nozzle and cylinder, and add a small amount of oil to the piston;
4. After each use, push the piston 3-4 times, move the residual straw to the nozzle, and then use the straw smoothly;
5. It is strictly forbidden to install and remove some of its electrical components when the suction tank device is opened.
6. When using a new suction tin pump for the first time, it is normal to produce a small amount of smoke due to heating. It will disappear naturally within ten minutes.
7. When using, it should be equipped with a natural cooling soldering iron base, and place the suction pen on the soldering iron base.
8. Before replacing welding parts or welding tips, please turn off the power supply and wait for the temperature of the welding tip to cool before operating.
9. This product has a ground wire and should be used with a socket with contacts. Please be careful.
1. Ensure that the voltage is consistent, the voltage is too high or too low is not conducive to use;
2. Before use, tighten the cylinder and suction nozzle to prevent leakage. Otherwise it will affect the suction.
3. Frequently clean the welding impurities in the suction nozzle and cylinder, and add a small amount of oil to the piston;
4. After each use, push the piston 3-4 times, move the residual straw to the nozzle, and then use the straw smoothly;
5. It is strictly forbidden to install and remove some of its electrical components when the suction tank device is opened.
6. When using a new suction tin pump for the first time, it is normal to produce a small amount of smoke due to heating. It will disappear naturally within ten minutes.
7. When using, it should be equipped with a natural cooling soldering iron base, and place the suction pen on the soldering iron base.
8. Before replacing welding parts or welding tips, please turn off the power supply and wait for the temperature of the welding tip to cool before operating.
9. This product has a ground wire and should be used with a socket with contacts. Please be careful.
Specifications:
Working voltage: EU plug 220V, USA plug 110V, 50hz
Heater power: 30W
Electromagnetic power: 350w (instantaneous)
Insulation class: E class
Working mode: continuous
Material: Plastic, Metal
Color: blue
Size: 245mm*30mm (length and width)
Specifications: EU Plug, US Plug
Working voltage: EU plug 220V, USA plug 110V, 50hz
Heater power: 30W
Electromagnetic power: 350w (instantaneous)
Insulation class: E class
Working mode: continuous
Material: Plastic, Metal
Color: blue
Size: 245mm*30mm (length and width)
Specifications: EU Plug, US Plug
Packing list:
1*Vacuum soldering pump
1*Extra Nozzle
1*Drill needle
1*Vacuum soldering pump
1*Extra Nozzle
1*Drill needle
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
30W Electric Vacuum Solder Sucker Pump Desoldering Gun Welding Iron Tools Blue
Product Introduction
Features:
1. Using 110/220V 50hz power supply, power 30W;
2. Turn on the power and preheat for 3-5 minutes;
3. Press the piston handle, and align the tin suction nozzle with the welding part; after the tank is melted, press the control button, and the welding seam is sucked into the cylinder;
4. The tank suction unit is equipped with two suction nozzles of different diameters, depending on the thickness of the lead parts;
5. When soldering, the operation is the same as that of a soldering iron; it can be used for both soldering and tin absorption
6. When disassembling the cylinder, press down the top of the cylinder in the direction of the arrow, and pull the cylinder and handle at the same time, the cylinder can be separated; when disassembling the suction nozzle, turn the suction nozzle counterclockwise and remove it;
1. Using 110/220V 50hz power supply, power 30W;
2. Turn on the power and preheat for 3-5 minutes;
3. Press the piston handle, and align the tin suction nozzle with the welding part; after the tank is melted, press the control button, and the welding seam is sucked into the cylinder;
4. The tank suction unit is equipped with two suction nozzles of different diameters, depending on the thickness of the lead parts;
5. When soldering, the operation is the same as that of a soldering iron; it can be used for both soldering and tin absorption
6. When disassembling the cylinder, press down the top of the cylinder in the direction of the arrow, and pull the cylinder and handle at the same time, the cylinder can be separated; when disassembling the suction nozzle, turn the suction nozzle counterclockwise and remove it;
Notes:
1. Ensure that the voltage is consistent, the voltage is too high or too low is not conducive to use;
2. Before use, tighten the cylinder and suction nozzle to prevent leakage. Otherwise it will affect the suction.
3. Frequently clean the welding impurities in the suction nozzle and cylinder, and add a small amount of oil to the piston;
4. After each use, push the piston 3-4 times, move the residual straw to the nozzle, and then use the straw smoothly;
5. It is strictly forbidden to install and remove some of its electrical components when the suction tank device is opened.
6. When using a new suction tin pump for the first time, it is normal to produce a small amount of smoke due to heating. It will disappear naturally within ten minutes.
7. When using, it should be equipped with a natural cooling soldering iron base, and place the suction pen on the soldering iron base.
8. Before replacing welding parts or welding tips, please turn off the power supply and wait for the temperature of the welding tip to cool before operating.
9. This product has a ground wire and should be used with a socket with contacts. Please be careful.
1. Ensure that the voltage is consistent, the voltage is too high or too low is not conducive to use;
2. Before use, tighten the cylinder and suction nozzle to prevent leakage. Otherwise it will affect the suction.
3. Frequently clean the welding impurities in the suction nozzle and cylinder, and add a small amount of oil to the piston;
4. After each use, push the piston 3-4 times, move the residual straw to the nozzle, and then use the straw smoothly;
5. It is strictly forbidden to install and remove some of its electrical components when the suction tank device is opened.
6. When using a new suction tin pump for the first time, it is normal to produce a small amount of smoke due to heating. It will disappear naturally within ten minutes.
7. When using, it should be equipped with a natural cooling soldering iron base, and place the suction pen on the soldering iron base.
8. Before replacing welding parts or welding tips, please turn off the power supply and wait for the temperature of the welding tip to cool before operating.
9. This product has a ground wire and should be used with a socket with contacts. Please be careful.
Specifications:
Working voltage: EU plug 220V, USA plug 110V, 50hz
Heater power: 30W
Electromagnetic power: 350w (instantaneous)
Insulation class: E class
Working mode: continuous
Material: Plastic, Metal
Color: blue
Size: 245mm*30mm (length and width)
Specifications: EU Plug, US Plug
Working voltage: EU plug 220V, USA plug 110V, 50hz
Heater power: 30W
Electromagnetic power: 350w (instantaneous)
Insulation class: E class
Working mode: continuous
Material: Plastic, Metal
Color: blue
Size: 245mm*30mm (length and width)
Specifications: EU Plug, US Plug
Packing list:
1*Vacuum soldering pump
1*Extra Nozzle
1*Drill needle
1*Vacuum soldering pump
1*Extra Nozzle
1*Drill needle
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.