Product Description
- Put the tube over one end of the fiber.
- Use fiber stripping pliers to strip fiber coating layer, the length of which is 30-40 mm. Use gauze dipping with alcohol or wadding to wrap the fiber, and then clean the bare part.
- Use a fiber cleaver to cut the fiber。Bare fiber length is 16 mm around.
- Put the finished fiber in the Fusion Splicer. Cross-section of fiber can not touch other things.
- Transfer fiber with protection sleeve from V-grooves to tube heater.
- Make sure the splice point is located at the center of the protection sleeve.
- Put the tube at the center of the heater.
- Pressto start tube heating. The buzzer beeps and the HEAT LED.
- Turn off when tube heating is completed.
- Remove the tube from the heater when the heater is cool. The whole process of Fusion Operation is completed.
- The input voltage of this model of machine is definite; please do not use the voltage outside the scope. Please use the correct AC and DC power supply.
- When the fusion splicer comes across the following failures, please immediately remove the AC power cord from the power supply input and turn off the fusion splicer, otherwise will lead to the incapable of the repairing and even will cause personal injury, death and fire.
- This model of fusion splicer does not have the need to maintain internal components, dismantling of fusion splicer and power modules is prohibited; any mistake in maintenance will lead to the machine beyond repair even causing bodily harm.
- The machine has strictly limitation to the power supply module used.
- The fusion splicer is prohibited to be used under the environment with the inflammable liquid or flammable gas; otherwise will lead to fire, explosion and other serious consequences.
JW4108S Optical Fiber Fusion Splicer with high performance price ratio, smart appearance, reliable quality. Optical Fiber Fusion Splicer is also called Cable Splicing Machine. It is mainly applied to the construction, maintenance, emergency repair and emergency repair of the optical cable lines of telecom operators, communication engineering companies and public institutions; and the experiment, production and testing of optical devices; scientific research and so on.
Fusion splicer is designed to splice many types of fiber by using core diameter aiming rationale, its shape is compact, light weight, which is suitable for field work. Operation is simple, fusion speed is high, and fusion loss is small.
In power modules: Fusion Splicer uses 3 in 1 power module design, during the work, the Fusion Splicer can be supplied by the polymer lithium ion battery separately; or use AC adapter for electricity supply; when adapter is used for electricity supply, the polymer lithium ion battery is charged at the same time. The lithium battery to be changed must be the model specified by the Company.
How to use:
1. Preparing
Verify that the machine is plugged in power or the battery capacity is enough; then press and hold the key until the machine is booted.
In the standby mode, press to enter “Splice Menu” menu. Move the cursor to [Operation Options]; press to enter. Set [Auto Start] [pause 1], [pause 2] respectively as “ON”,“OFF”,“OFF”.
Discharge Calibration:
Discharge calibration is needed because constant changing of atmospheric conditions such as temperature and pressure, and the long service of the machine creates variability in the arc temperature and position.
Step of discharge calibration:
In the [ Ready ] mode, press to enter “Splice Menu” menu. Then prepare and place fiber according to the method described in fiber preparation. Close the wind protector. Press to enter [Arc Calibration]. Discharge calibration automatically starts. The user is recommended to repeatedly prepare and place fiber in discharge calibration interface, until the “Step II of discharge calibration completed” message is displayed for three times.
Note: Discharge calibration is needed only arc power fluctuates strongly, it is not necessary upon boot every time. After discharge calibration is completed, the machine will adjust the arc discharge current according to the calibration results to ensure fusion quality.
2. Fiber preparation.
4. Reinforce the fusion point.
Warning:
Fusion splicer is designed to splice many types of fiber by using core diameter aiming rationale, its shape is compact, light weight, which is suitable for field work. Operation is simple, fusion speed is high, and fusion loss is small.
In power modules: Fusion Splicer uses 3 in 1 power module design, during the work, the Fusion Splicer can be supplied by the polymer lithium ion battery separately; or use AC adapter for electricity supply; when adapter is used for electricity supply, the polymer lithium ion battery is charged at the same time. The lithium battery to be changed must be the model specified by the Company.
How to use:
1. Preparing
Verify that the machine is plugged in power or the battery capacity is enough; then press and hold the key until the machine is booted.
In the standby mode, press to enter “Splice Menu” menu. Move the cursor to [Operation Options]; press to enter. Set [Auto Start] [pause 1], [pause 2] respectively as “ON”,“OFF”,“OFF”.
Discharge Calibration:
Discharge calibration is needed because constant changing of atmospheric conditions such as temperature and pressure, and the long service of the machine creates variability in the arc temperature and position.
Step of discharge calibration:
In the [ Ready ] mode, press to enter “Splice Menu” menu. Then prepare and place fiber according to the method described in fiber preparation. Close the wind protector. Press to enter [Arc Calibration]. Discharge calibration automatically starts. The user is recommended to repeatedly prepare and place fiber in discharge calibration interface, until the “Step II of discharge calibration completed” message is displayed for three times.
Note: Discharge calibration is needed only arc power fluctuates strongly, it is not necessary upon boot every time. After discharge calibration is completed, the machine will adjust the arc discharge current according to the calibration results to ensure fusion quality.
2. Fiber preparation.
4. Reinforce the fusion point.
Warning:
Feature
- FTTH applicable to the environment, can also be used for ordinary optical fiber engineering
- The PAS core to ensure accurate alignment, low connecting loss
- 8 seconds - 30 seconds of welding, heat shrinkable
- The X/Y axis X/Y axis or a separate display shows at the same time, 300/200 times magnification
- 5 - inch digital high-definition LCD screen, while observing the X axis and Y axis direction of the optical fiber
- Three in one fixture, welding core, flex, pigtail
- The built-in high-capacity lithium battery, can be completed 200 times and continuous heating
- The small size and light weight, only 2.5kg with battery
Specifications
- Model: JW4108S
- Splicing Type: SM, MM, DS, NZDS
- Splicing Loss: 0.02dB(SM), 0.01dB(MM), 0.04dB(DS)
- Return Loss: >60dB
- Splicing Mode: Manual, Half Auto, Auto
- Applicable Fiber Cable: Indoor And 0.25mm,0.9mm Fiber, SC Connector (Option)
- Splicing Time: ≤9s
- Heat Time: ≤30s
- Cleaved Length: 8～16mm
- Fiber Image/ Magnification: 300/200 Times
- View Display: 5 Inch Digital High-Quality LCD Screen
- Tension Test: Standard 2N (Option)
- Heat Shrinkable Sleeve: 60mm, 40mm And Serials Heat Shrinkable Sleeve
- Battery Capacity: 200 Cycles Splicing And Heating, 3 Hours Charging Time
- (Splicing And Charging At Same Time)
- Battery Life: Cycling Charge 300-500 Times, Easy To Replace Battery
- Electrodes Life: 3000, Easy To Replace Electrodes
- Power Source: ≤20W
- Interface: USB Convenient Data Download And Software Update
- Construction Lighting: Built In High Brightness, Wide Range Of Lights, Easy To Operate At Night
- Power Supply: Built In Lithium Battery 5200mAh 11.1V; External Adapter, Input: AC100-240V, Output: DC13.5V/4.5A
- Operating Condition: 0-5000m Above Sea Level
- Temperature: -10-60℃
- Humidity: 0～95%RH (No Dew)
- Weight (Including Battery): 2.5 KG (Including Battery)
- Dimension (LxWxH): 165mm × 155mm × 150mm
- We ship within 2 business day.
- Ship to eBay confirmed address ONLY
- Shipping to USA, Australia, UK, RU: Ship via USPS First Class Mail. ETA 8 to 15 business days.
- International Shipping: Ship via China Postal Service Airmail. ETA 15 to 30 business days.
- International Shipping: Ship via DHL/UPS/EMS Express. ETA 3 to 8 busines
- You may sometimes experience longer delivery time due to customs-related delays. Please let us know. ( No service on Sundays and public holidays), Buyers are responsible for any international customs and duties that may apply.
- We accept payment by PayPal.
- Immediate payment is required.
- Buyer pays return shipping.
- We guarantee you a five star shopping experience with us. If you are not satisfied with your purchase, please contact us within 30 days of receipt to return it for a refund or exchange.
- If our product does not work properly for you and you want to exchange another one or get a refund, please confirm with our customer service first and list the product detailed problems.
- Please don't open case via ebay or paypal.
- We keep our promises that we will provide you with the best solution within 24 hours.
Shipping
Payment
Returns
Feedback |
Powered by SoldEazy