M6 Gas Strut Angle Joint DIN 71802 10mm Ball, 21mm Reach – 2 Pack | SpringFix UK

🔧 Not sure which fitting you need? Use our free Fitting & Bracket Finder before you order — takes 10 seconds and helps you avoid ordering the wrong part. M6 Gas Strut Angle Joint DIN 71802 — 2 Pack, 10mm Ball, 21mm Reach Genuine DIN 71802 angle joint (also known as an angled ball joint) — the trade-standard gas strut fitting that combines a ball joint socket and a threaded mounting stud in one part. The M6 ball joint socket (10mm ball, female thread) connects to your gas strut's threaded rod end, while the integrated M6 mounting stud (male thread) bolts straight into your bracket or panel — no separate stud or extra nut needed on that side. A safety-catch clip retains the ball and allows a swivel angle of roughly 15–18°. Zinc-plated steel with an SW10 hex flat for easy tightening. Key Specifications Standard: DIN 71802 angle joint (ball socket DIN 71805 + ball stud DIN 71803) Ball joint socket thread: M6 female Mounting stud thread: M6 male Ball diameter: 10mm Wrench flat (hex): SW10 Overall reach: 21mm (ball centre to socket thread end) Swivel angle: approx. 15–18°, retained by safety-catch clip Construction: 11SMnPb30 steel, zinc plated Perfect For Custom gas strut brackets and enclosures Machine guard and cabinet door gas strut mounts DIY and workshop gas strut installations Replacing a damaged, corroded or missing angle joint Projects needing a fixed, precise mounting geometry without extra loose bracket parts Compatibility The 10mm ball joint socket (M6 female thread) screws onto any gas strut with a matching M6 male-threaded rod end. The M6 mounting stud bolts through a clearance hole in your bracket or panel — use a nut and washer (nyloc recommended). We stock this angle joint in several reach lengths with the same thread sizes, so please double-check the 21mm reach measurement against your original part or bracket before ordering, to avoid receiving the wrong length and needing a return. Installation Tips Screw the ball joint socket end onto your gas strut's M6 threaded rod Bolt the M6 stud through your bracket with a suitable washer and nyloc nut Use an SW10 spanner on the hex flat to hold the fitting steady while tightening the stud Always fit as a matched pair for balanced gas strut operation Frequently Asked Questions What is an angle joint? An angle joint (DIN 71802) is a standard gas strut and linkage fitting that combines a ball joint socket and a threaded ball stud in one part, set at a fixed angle. It's also called an angled ball joint, and it's the correct term if you're comparing parts between suppliers. How do I know I've got the right reach length? Measure your existing part from the centre of the ball to the end of the threaded socket. We stock several reach lengths in this thread/ball combination — the reach measurement is the easiest way to confirm you're ordering the right one. Can I use these outdoors? Zinc plated for sheltered outdoor use. For marine or fully exposed environments, get in touch about stainless options. Do I need a nut for the mounting stud? Yes — a M6 nut and washer (nyloc recommended) are needed for the stud end; these are not included. Fast UK Dispatch Orders placed Monday to Sunday before 16:00 are dispatched same-day from UK stock via Royal Mail, Yodel, UPS or DPD.

M6 Gas Strut Angle Joint DIN 71802 10mm Ball, 21mm Reach – 2 Pack | SpringFix UK

🔧 Not sure which fitting you need? Use our free Fitting & Bracket Finder before you order — takes 10 seconds and helps you avoid ordering the wrong part.

M6 Gas Strut Angle Joint DIN 71802 — 2 Pack, 10mm Ball, 21mm Reach

Genuine DIN 71802 angle joint (also known as an angled ball joint) — the trade-standard gas strut fitting that combines a ball joint socket and a threaded mounting stud in one part. The M6 ball joint socket (10mm ball, female thread) connects to your gas strut's threaded rod end, while the integrated M6 mounting stud (male thread) bolts straight into your bracket or panel — no separate stud or extra nut needed on that side. A safety-catch clip retains the ball and allows a swivel angle of roughly 15–18°. Zinc-plated steel with an SW10 hex flat for easy tightening.

Key Specifications

  • Standard: DIN 71802 angle joint (ball socket DIN 71805 + ball stud DIN 71803)
  • Ball joint socket thread: M6 female
  • Mounting stud thread: M6 male
  • Ball diameter: 10mm
  • Wrench flat (hex): SW10
  • Overall reach: 21mm (ball centre to socket thread end)
  • Swivel angle: approx. 15–18°, retained by safety-catch clip
  • Construction: 11SMnPb30 steel, zinc plated

Perfect For

  • Custom gas strut brackets and enclosures
  • Machine guard and cabinet door gas strut mounts
  • DIY and workshop gas strut installations
  • Replacing a damaged, corroded or missing angle joint
  • Projects needing a fixed, precise mounting geometry without extra loose bracket parts

Compatibility

The 10mm ball joint socket (M6 female thread) screws onto any gas strut with a matching M6 male-threaded rod end. The M6 mounting stud bolts through a clearance hole in your bracket or panel — use a nut and washer (nyloc recommended). We stock this angle joint in several reach lengths with the same thread sizes, so please double-check the 21mm reach measurement against your original part or bracket before ordering, to avoid receiving the wrong length and needing a return.

Installation Tips

  • Screw the ball joint socket end onto your gas strut's M6 threaded rod
  • Bolt the M6 stud through your bracket with a suitable washer and nyloc nut
  • Use an SW10 spanner on the hex flat to hold the fitting steady while tightening the stud
  • Always fit as a matched pair for balanced gas strut operation

Frequently Asked Questions

What is an angle joint? An angle joint (DIN 71802) is a standard gas strut and linkage fitting that combines a ball joint socket and a threaded ball stud in one part, set at a fixed angle. It's also called an angled ball joint, and it's the correct term if you're comparing parts between suppliers.

How do I know I've got the right reach length? Measure your existing part from the centre of the ball to the end of the threaded socket. We stock several reach lengths in this thread/ball combination — the reach measurement is the easiest way to confirm you're ordering the right one.

Can I use these outdoors? Zinc plated for sheltered outdoor use. For marine or fully exposed environments, get in touch about stainless options.

Do I need a nut for the mounting stud? Yes — a M6 nut and washer (nyloc recommended) are needed for the stud end; these are not included.

Fast UK Dispatch

Orders placed Monday to Sunday before 16:00 are dispatched same-day from UK stock via Royal Mail, Yodel, UPS or DPD.

Shipping info

Click the Shipping & Payments tab above the listing description for more info

Click the Shipping & Payments tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYMENT


Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & eBay App).

Thank you for shopping with us on eBay!

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© SpringFixUk

Shipping is calculated on eBay, click the Shipping & Payments tab above the listing description for more information.

Accepted Payment Methods

Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & eBay App).

Thank you for shopping with us on eBay!

Returns are accepted

Items must be returned within of the auction ending

Seller will pay for return shipping.