Features:
1. Exact OE Fitment: Direct OEM Replacement For Part Number 4053872, Exclusively Designed For Ford Focus Turn Signal Light Assembly. This Pack Comes With 2 Complete Bulb Holders To Replace Both Left And Right Lamp Sockets In A Single Purchase. Precision Molded Locking Tabs, Standard 2-Pin Gold-Plated Internal Terminals And Integrated Built-In Waterproof Gasket Perfectly Match Original Car Lamp Housing And Wiring Plug, Effectively Preventing Loose Bulb Contact, Signal Flickering, Moisture Intrusion And Vibration Shaking After Installation. Please Compare Your Old Socket’s Shape, Pin Layout And OE Number Before Ordering To Avoid Fitment Mismatch And Extra Return Shipping Fees.
2. Heat Resistant Premium Material Build: The Entire Outer Casing Is Constructed From Reinforced High-Temperature Engineering Plastic, Which Resists Melting, Cracking And Long-Term Aging Caused By Continuous Heat Released From Turn Signal Halogen Bulbs. Internal Conductive Contacts Adopt Thick Gold-Plated Copper Pins To Block Oxidation, Rust And High Electrical Resistance In Rainy, Snowy, Salty Coastal Or Humid Driving Conditions. The Sealed Integrated Rubber Ring Forms A Tight Protective Barrier Against Road Mud, Dust And Water, Stopping Circuit Shortage, Intermittent Light Failure And Premature Bulb Burnout In All Daily Driving Scenarios.
3. Stable Safe Electrical Conductivity: Built-In Elastic Copper Spring Clips Maintain Constant Firm Clamping Force On The Lamp Bulb Base, Delivering Smooth, Steady Current Transmission For Clear Rear Turn Signal Flashing. It Fixes Common Factory Socket Faults Including Hyper-Flashing Signals, Dim Turn Lights, Intermittent Lamp Cutoff And Complete Light Blackout From Worn Out Internal Contacts. Low-Resistance Conductive Structure Greatly Reduces Overheating Risks, Avoids Melted Wiring Harness And Potential Electrical Fire Hazards, Boosting Rear Driving Visibility For Lane Changes, Night Travel And Foggy Road Safety.
4. Tool-Free Plug-And-Play Diy Installation: No Wire Cutting, Harness Modification Or Expensive Professional Auto Repair Tools Are Needed For Replacement. Follow Simple Steps For Beginner Car Owners: Disconnect Vehicle Battery Power, Unplug The Wiring Connector From Damaged Old Socket, Twist To Remove Broken Holder From Rear Lamp Housing, Align And Fully Seat The New Socket Until Lock Tabs Snap Securely, Reconnect The Wiring Plug And Install The Signal Bulb. Single Socket Replacement Takes Less Than 3 Minutes, Helping You Save Costly Mechanic Labor Fees For Home Garage Vehicle Maintenance.
5. Multi-Scenario Practical Replacement Value: Ideal Direct Swap Solution For Cracked, Melted, Corroded, Burnt Or Loose Stock Rear Turn Signal Bulb Holders On For Ford Focus Models. Perfect Fit For Daily City Commuting, Night Highway Driving, Long-Distance Family Road Trips And Mandatory Annual State Vehicle Safety Inspections. The Neutral Gray OEM-Matching Shell Blends Seamlessly With Lamp Internal Structure. The 2-Pack Bundle Allows Simultaneous Replacement Of Dual Light Sockets, Offering Better Cost Performance Than Single-Socket Separate Listings.
Specifications:
Type: Light Bulb Socket
Condition: 100% New
Material: Plastic
Placement On Vehicle: Left, Right
Function: Turn Signal / Reverse / Rear Fog Light Bulb Socket
OEM: 4053872, XS41-13K370-AC
Fitment:
For Ford Focus Mk1 (1998–2005)
For Ford Focus Mk2 (2004–2011)
For Ford Focus C-Max Mk1 (2003–2007)
For Ford Kuga Mk1 (2008–2012)
For Ford Transit (2000–2006)
Packaging Includes:
2* Light Bulb Socket
1. Exact OE Fitment: Direct OEM Replacement For Part Number 4053872, Exclusively Designed For Ford Focus Turn Signal Light Assembly. This Pack Comes With 2 Complete Bulb Holders To Replace Both Left And Right Lamp Sockets In A Single Purchase. Precision Molded Locking Tabs, Standard 2-Pin Gold-Plated Internal Terminals And Integrated Built-In Waterproof Gasket Perfectly Match Original Car Lamp Housing And Wiring Plug, Effectively Preventing Loose Bulb Contact, Signal Flickering, Moisture Intrusion And Vibration Shaking After Installation. Please Compare Your Old Socket’s Shape, Pin Layout And OE Number Before Ordering To Avoid Fitment Mismatch And Extra Return Shipping Fees.
2. Heat Resistant Premium Material Build: The Entire Outer Casing Is Constructed From Reinforced High-Temperature Engineering Plastic, Which Resists Melting, Cracking And Long-Term Aging Caused By Continuous Heat Released From Turn Signal Halogen Bulbs. Internal Conductive Contacts Adopt Thick Gold-Plated Copper Pins To Block Oxidation, Rust And High Electrical Resistance In Rainy, Snowy, Salty Coastal Or Humid Driving Conditions. The Sealed Integrated Rubber Ring Forms A Tight Protective Barrier Against Road Mud, Dust And Water, Stopping Circuit Shortage, Intermittent Light Failure And Premature Bulb Burnout In All Daily Driving Scenarios.
3. Stable Safe Electrical Conductivity: Built-In Elastic Copper Spring Clips Maintain Constant Firm Clamping Force On The Lamp Bulb Base, Delivering Smooth, Steady Current Transmission For Clear Rear Turn Signal Flashing. It Fixes Common Factory Socket Faults Including Hyper-Flashing Signals, Dim Turn Lights, Intermittent Lamp Cutoff And Complete Light Blackout From Worn Out Internal Contacts. Low-Resistance Conductive Structure Greatly Reduces Overheating Risks, Avoids Melted Wiring Harness And Potential Electrical Fire Hazards, Boosting Rear Driving Visibility For Lane Changes, Night Travel And Foggy Road Safety.
4. Tool-Free Plug-And-Play Diy Installation: No Wire Cutting, Harness Modification Or Expensive Professional Auto Repair Tools Are Needed For Replacement. Follow Simple Steps For Beginner Car Owners: Disconnect Vehicle Battery Power, Unplug The Wiring Connector From Damaged Old Socket, Twist To Remove Broken Holder From Rear Lamp Housing, Align And Fully Seat The New Socket Until Lock Tabs Snap Securely, Reconnect The Wiring Plug And Install The Signal Bulb. Single Socket Replacement Takes Less Than 3 Minutes, Helping You Save Costly Mechanic Labor Fees For Home Garage Vehicle Maintenance.
5. Multi-Scenario Practical Replacement Value: Ideal Direct Swap Solution For Cracked, Melted, Corroded, Burnt Or Loose Stock Rear Turn Signal Bulb Holders On For Ford Focus Models. Perfect Fit For Daily City Commuting, Night Highway Driving, Long-Distance Family Road Trips And Mandatory Annual State Vehicle Safety Inspections. The Neutral Gray OEM-Matching Shell Blends Seamlessly With Lamp Internal Structure. The 2-Pack Bundle Allows Simultaneous Replacement Of Dual Light Sockets, Offering Better Cost Performance Than Single-Socket Separate Listings.
Specifications:
Type: Light Bulb Socket
Condition: 100% New
Material: Plastic
Placement On Vehicle: Left, Right
Function: Turn Signal / Reverse / Rear Fog Light Bulb Socket
OEM: 4053872, XS41-13K370-AC
Fitment:
For Ford Focus Mk1 (1998–2005)
For Ford Focus Mk2 (2004–2011)
For Ford Focus C-Max Mk1 (2003–2007)
For Ford Kuga Mk1 (2008–2012)
For Ford Transit (2000–2006)
Packaging Includes:
2* Light Bulb Socket
