eBay

IMPORTANT - CHECK YOUR OLD RELAY BEFORE ORDERING

Miele dishwashers can use two different heater relay types depending on age and production version.

This listing is for the older style heater relay, part number 6002930.

Please do not order by dishwasher model number only. Before buying, compare your old relay with the photos and check:

* Part number on the relay
* Relay shape and mounting
* Terminal layout
* Connector position

If your old relay does not match this part, this relay will not fit or repair the fault, even if your dishwasher shows F24 or a heater relay fault.

F24 can be caused by the heater relay, but it can also be caused by other heating circuit faults. Match the relay first before ordering.

Genuine Miele Dishwasher Heater Relay – OEM | Part #6002930

Condition: Brand New, Genuine OEM
Part Number: 6002930
Rated: 220–240V AC, 16A, 50/60Hz
Manufacturer: Schrack (Tyco Electronics, Austria)

Return Policy

No returns accepted on fitted or used items.
All warranty claims must include a qualified technician’s report confirming the part is faulty.
Buyer is responsible for compatibility and installation. Consult a licensed technician if unsure.

Product Overview

This is a genuine Schrack (Tyco Electronics) heater relay used in the power control module of many Miele dishwashers. Common symptoms of failure include:

Error code F24
No heat / cold wash cycles
Clicking or buzzing noises from relay
Burnt PCB near relay contacts

Rated for 16A @ 250V AC with bifurcated contacts and >3mm contact gap. OEM design is optimized for 230V Australian mains.

Important Disclaimer

The F24 error can have multiple causes, not just the heater relay. If replacing this relay doesn’t fix the issue, it may not be the source of the problem. A licensed technician should perform a full diagnosis. Refunds or warranty claims require a written technician’s report confirming the relay is faulty.

Key Features

OEM Quality: Manufactured by Schrack – Tyco Electronics (original Miele supplier)
Relay Type: RAST 5 double-pole, normally open (2NO)
Terminals: 6.3mm quick-connect push terminals
Mounting: Snap or screw-fit to control board
Safety: 4kV coil-to-contact insulation, >3mm contact gap
Optimized for AU: Designed for 230V Australian mains vs older 200V variants

Model Compatibility

Compatible with the following Miele dishwasher series and models (verify your model from the inner door label or user manual):

G1000 Series:
G1870, G1020, G1021, G1022, G1023, G1040, G1041, G1042, G1102, G1120, G1130, G1140, G1142, G1142 SCU, G1150, G1152, G1162, G1170, G1171, G1172, G1173, G1174, G1180, G1182, G1190, G1191, G1220, G1220SCU, G1221PLUS, G1230, G1270, G1290, G1291, G1320, G1330, G1370, G1420, G1421GALA, G1430, G1430 -60, G1520, G1530, G1570, G1630, G1670, G1730, G1830

Advanta Series:
G2020, G2022, G2023, G2040, G2042, G2180, G2182, G2191

Inspira Series:
G2130, G2140, G2142

Diamante Series:
G2150, G2152

G2000 Series:
G2170, G2171, G2172, G2173, G2174, G2220, G2220SCI, G2230, G2270, G2290, G2291, G2330, G2370, G2420, G2520, G2530, G2570

Optima Series:
G1470, G2430, G2470

Excella Series:
G2630, G2670, G2670 -60, G2730

La Perla Series:
G2830, G2870

Futura Classic:
G4100, G4101, G4105, G4170, G4171, G4175

Futura Crystal:
G4500, G4570, G5170, G5175

Semi-Commercial (G8000):
G8050, G8050 U, G8051 I CLST, G8051 I ED

ProfiLine Series (Professional / Commercial PG):
PG8052 CLST, PG8052 ED, PG8080/i/u, PG8081i, PG8082SCi, PG8083SCVi, PG8120, PG8130, PG8131

DIY Installation Notes

Always disconnect power before service
Remove panel and locate control board (front/top access)
Unplug existing relay, match terminal layout
Snap/screw into place and reassemble
No reprogramming required

Suitable for experienced DIYers or licensed technicians. Approx. installation time: 15–30 minutes.

Frequently Asked Questions (FAQ)

Is this a genuine Miele part?
This is an OEM part made by Schrack (Tyco Electronics) – the same supplier used by Miele.

Is this version better for Australia?
Yes. It is optimized for 230V, the standard in Australian homes, offering improved reliability and lower heat output.

What does the relay control?
It controls the heating circuit on/off via the control board. A faulty relay often causes water not to heat and triggers error F24.

Can I install this myself?
Yes, if you have electrical experience. Otherwise, hire a technician. It is plug-compatible and needs no software reset. Note: warranty support is void if not installed by a licensed technician.

What’s your return policy?
No returns accepted if the part is installed or packaging is opened. Faulty claims require a technician’s report.