- - Adopts Japan's first "all-around" ring-emitting LED light, optimal balance, all-around slim head, and comfortable operability. *For domestic rechargeable impact drivers. As of December 2022, according to Makita research. Visibility during work has been significantly improved. Approximately 2.5 times brighter (compared to Makita's previous 18V model). Illuminance can be switched in 3 levels (strong/medium/weak). *For domestic rechargeable impact drivers. As of December 2022, according to Makita research. Can also be used as a work light. . It can also be used as a simple light in "light mode".Lighting time is about 1 hour.・New trigger switch. Intuitive trigger shift operation is possible from low to high speeds.Grip part close to shaft center. The hand you hold is close to the head, making it easy to press the shaft core. Reduces cam-out. Offsets the battery to the rear. Optimized center of gravity position allows for balanced tightening in all directions.Also reduces interference with obstacles.Easy-to-see and easy-to-use operation panel located at the "rear" position. You can operate the mode and check the remaining battery capacity while holding it.・Bit runout is the lowest in the industry, and double ball bearings are used. Newly shaped bit sleeve. Ribs on the edges prevent damage even if the sleeve hits a component. *For domestic cordless impact drivers. According to Makita research, December 2022. Tilt angle of approximately 10.5°. Excellent corner driving performance reduces cam-out. Comfortable when working near walls. The most suitable mode can be selected according to the work. Mode memory function. By pressing two buttons at the same time, you can register one frequently used mode.Use the button at hand to switch between the "most recently used mode" and the "registered mode."・DC 18V, sliding type Li-ion battery specification. Battery and charger sold separately. Tightening capacity: Machine screws M4 to M8/Ordinary bolts M5 to M16/High strength bolts M5 to M14/Coarse thread 22 to 125mm. Maximum tightening torque: 180N・m. Rotation speed [revolutions/min]: Fastest 0-3,600/strong 0-3,200/medium 0-2,100/weak 0-1,100. Easy mode rotation speed [rotations/min]: Wood 0-1,800/Volt 0-3,600/Tex thin plate 0-2,900/Tex thick plate 0-3,600. Number of blows [times/min]: Fastest 0 to over 3,800 Medium 0 to 3,600 0 to under 2,600 0 to 1,100. Easy mode number of blows [times/min]: Wood 0 to 3,800/Volt 0 to 3,800/Tex thin plate Stops immediately after the start of the blow/Tex thick plate 0 to 2,600. 1 charge work amount (wood screws material lauan φ4.3 x 65 mm Approximately 960 pieces- Dimensions of this machine: length 111mm x width 81mm x height 234mm. Mass: 1.5kg (including battery)Japan's first "all-around" ring emitting LED light adopted, optimal balance & all-around slim head & comfortable operability*For domestic rechargeable impact drivers. As of December 2022, according to Makita research.Visibility during work is greatly improved. Approximately 2.5 times brighter (compared to Makita's previous 18V model). Illuminance can be switched in 3 levels (strong/medium/weak). *For domestic rechargeable impact drivers. As of December 2022, according to Makita research.It can also be used as a work light. Can also be used as simple lighting in "Light Mode". Lighting time is approximately 1 hour.New trigger switch. Intuitive trigger shift operation is possible from low to high speeds.A grip close to the axis. The hand you grip is close to the head, making it easy to press the shaft core. Reduces come-outs.Offset the battery backwards. Optimized center of gravity position allows for balanced tightening in all directions. Furthermore, interference with obstacles is also reduced.Easy-to-see and easy-to-use operation panel with a "rear" layout. You can operate the mode and check the remaining battery capacity while holding it.Bit runout is the industry's smallest, and double ball bearings are used. New shape bit sleeve. Ribs are provided on the edges to prevent damage even if the sleeve hits a member. *For domestic rechargeable impact drivers. According to Makita research, December 2022.Tilt angle approximately 10.5°. Excellent corner striking performance reduces cam-out. Comfortable to work near walls.You can select the most suitable mode according to your work. Mode memory function. By pressing two buttons at the same time, you can register one frequently used mode. Switch between the "previously used mode" and "registration mode" with the button on hand.18V DC, sliding Li-ion battery specifications. Battery and charger sold separatelyTightening capacity: Machine screw M4~M8/Ordinary bolt M5~M16/High strength bolt M5~M14/Coarse thread 22~125mmMaximum tightening torque: 180N・mRotation speed [rotations/min]: Fastest 0~3,600/strong 0~3,200/medium 0~2,100/low 0~1,100Easy mode rotation speed [rotations/min]: Wood 0~1,800/Volt 0~3,600/Tex thin plate 0~2,900/Tex thick plate 0~3,600Number of blows [times/min]: Fastest 0~3,800+ 0~3,600 Medium 0~2,600~ 0~1,100Easy mode number of blows [times/min]: Wood 0~3,800/Volt 0~3,800/Tex thin plate Stops immediately after the start of blow/Tex thick plate 0~2,6001 charge work amount (wood screws material lauan φ4.3 x 65mm approximation): Approximately 960 piecesMachine dimensions: length 111mm x width 81mm x height 234mmMass: 1.5kg (including battery)