Nema24 Closed loop servo motor 3N.m 88mm

Specific

• Size:60x60x88mm
• Current :5A
• Phase:2
• Step Angle(degrees):1.8 degree
• Lead wire:4pcs
• Holding Torque:3N.m
• Resistance:0.5±10%Ω
• Inductance:1.8±20%mH
• Insulation resistance:100MOhm(500V DC)
• Insulation Class:B

Features

1.2.1 Stepper motor closed loop system, never lose step.

1.2.2 Improve motor output torque and working speed.

1.2.3 Automatic current adjustment based on load, lower temperature rising.

1.2.4 Suitable for all mechanical load conditions (include low rigidity belt pulley and wheel), no need

to adjust gain parameter.

1.2.5 Motor work smoothly and low vibration, high dynamic performance at acceleration and

deceleration.

1.2.6 No vibration from high speed to zero speed

1.2.7 Drive nema 24 series 3N.m closed loop stepper motor.

1.2.8 Pulses response frequency can reach 200KHZ

1.2.9 16 kinds microsteps choice, highest 51200 microsteps/rev.

1.2.10 Voltage range: DC24V~50V

1.2.11 Over-current, over-voltage and position ultra difference protection function

Wiring diagram

Applications

• Closed loop stepper system can be applied to all kinds small automatic equipment and Instruments, such as engraving machine, special industrial sewing machine, stripping machine, marking machine, Dispensing machine, cutting machine, module phototypesetting, graph plotter, NC machine, automatic, assembly equipment and so on.

• ♞【4 Axis USB Mach3 Control Board】USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.As long as Mach3 can run,the control card can be used; Support computer system:Windows XP/7/8.
• ♞【4 Axis Linkage】Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives; Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;One status LED, indicate connection status on the board.
• ♞【Output Signal Ports】Have 0-10V signal output,you can use mach3 software to control the spindle motor speed; 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device;Support for connecting electronic handwheel;Handwheel interface: 2*5P row needle.
• ♞【Input Signal Ports】4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device; Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.
• ♞【Applications】CNC Router,Milling Machine,Engraving Machine,Carving Machines,Cutting industry,Medical equipment,industrial equipment and automation devices etc.

• Product Description

  

   

  

  4 Axis USB Mach3 Motion CNC Controller Card

  1. USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface;
  2. As long as Mach3 can run, the control card can be used;
  3. Number of control axis: X.Y.Z.A axis;
  4. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor.
  5. Support computer system:Windows 2000/ XP / Windows 7/8.

  Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives; Support for connecting electronic handwheel;Handwheel interface: 2 * 5P row needle Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor; Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.	Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable. MCU model: three generation 32-bit STM processor Communication plug-in: RnR motion control card - ECO-2.0 One status LED, indicate connection status on the board.	4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device. 4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.

  Wiring diagram

  

  Please strictly follow the instructions and warnings before using this product:

  • It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.
  • The output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.
  • This interface can output 0-10V analog signals, and can also be configured as 0-5V output.
  • USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.
  • This control board does not require any drivers to be installed,as long as Mach3 can run, the control card can be used;
  • Whether frequency converter is supported: Yes
  • Support PWM: Yes

  

  • The inverter interface (AVI+, AVI -) is isolated from the computer and main control circuit to isolate interference signals.
  • This interface can output 0-10V analog signals or be configured to output 0-5V.
  • It is recommended to first install limit switches and emergency stop switches.
  • If these protective switches are not installed,in addition to pressing the emergency stop button to return and turn off the motor power, the most convenient stopping method is to unplug the USB cable to stop the machine.

  

  • Widely use in CNC Router,Milling Machine,Engraving Machine,Carving Machines,Cutting industry,Medical equipment,industrial equipment and automation devices etc.